Live Chat Software by Kayako |
Our Answer:
It is likely that some of our smaller direct vent inserts could work
for your needs, however I will need to know a bit more information
about your fireplace to be certain. What is the depth of the unit from
the front of the opening to the...
Our Answer:
True Heat is indeed out of business and parts are no longer available
for their products. However, we do offer universal refractory liners
that can be cut to fit and installed into fireplaces that are still in
good shape otherwise. For yo...
Our Answer:
The original glass door assemblies that are listed for this unit have
been discontinued. However, it is possible to retrofit one of the
current Majestic/Monessen door assemblies to this unit. The assembly
that will fit is the Majestic Sta...
Our Answer:
It is certainly possible to install a wood burning insert in some
manufactured boxes, but I simply cannot say for sure with your model
of Marco. I was unable to find a manual for this unit, so I am unable
to verify. I do not recommend it ...
Our Answer:
Just to clarify, are you referring to a key for a manual gas valve,
such as this item? Gas Valve Manual Key [1]. If so, the key that is
pictured is the most common type and measures 3 inches in length, with
a 1/4" socket end. My recommend...
Our Answer:
If you are referring to the Type S triple-wall Majestic pipe that has
an 8" inner diameter, 11" diameter second wall and a 13 3/8" outer
diameter, please see the appropriate cap here: Round Louvered
Termination for Majestic 8 in. Diameter...
Our Answer:
Per the supplied model number, these appear to be vent-free gas logs
manufactured by ProCom. Whether or not you can use a blower will
depend on the model of fireplace you have, as the blower assembly will
be housed in the base of the unit...
Our Answer:
We do carry several twin blower fireplace fans, but they are of a
lower CFM output and have a larger housing size than you require. From
what I have seen, RSF fireplaces use a uniquely designed fan assembly
that is slimmer than most. As s...
Our Answer:
Circulating fireplaces will have stamped or removable metal louvers
above and below the face of the fireplace. Some clean face models will
have narrow slits in the top or sides instead. This allows you to
equip these units with an accesso...
Our Answer:
Per your model number, the fireplace was manufactured by Marco, which
is a brand that has since been absorbed by Lennox Hearth Products. We
are unable to procure the original liner panel, however we do offer
the Hargrove Replacement Firep...
Our Answer:
While we do not have the manufacturer-specific panel that you are
looking for, we do offer some universal refractory panels that will
work for your wood-burning fireplace. Please see the following links:
One 24\" h x 28\" w Panel [1]. Two...
Our Answer:
Unfortunately, we do not offer an oval adapter that will fit the
opening size of your stove. Based on the nonstandard dimensions of
your opening, you may need to have an adapter custom fabricated by a
sheet metal manufacturer. As more sto...
Our Answer:
Unfortunately, I was unable to find detailed information about this
particular stove and it appears that this manufacturer has gone out of
business. As such, I am not certain if a particular blower housing
will fit onto this stove. Nevert...
Our Answer:
Depending on what needs to be replaced on your Eco Fan, we may be
able to find parts for the fan. Replacing parts, such as the motor,
involve no more than simply removing the fan blade and several 2
screws holding the motor in place.
F...
Our Answer:
We offer a universal blower temperature switch that could be used
with your existing blower assemblies. The Hearth Products Controls BSK
Blower Sensor Kit [1] is designed to modulate the operation of your
fans based on the temperature of ...
Our Answer:
Yes, the MBU36 fireplace can use the 36GDKBK bi-fold glass doors [1]
with a retro-fit spacer kit (part #20000407). The fit kit is a special
order item, so you would need to call us to order.
From Section Page: Fireplace Doors [2]
ID:...
Our Answer:
CFM is no longer in business - their holdings were taken over by the
Majestic corporation. Unfortunately, per Majestic there is no longer a
conversion kit available for your Insta-Flame fireplace. Fuel
conversion can simply not be done. I...
Our Answer:
Unfortunately, we do not have the manufacturer-specific panel that
you are looking for, but we do offer some universal refractory panels
that will work for your woodburning fireplace. Please see the
following links: One 24\"h x 28\"w Pane...
Our Answer:
A heater with a 30,000 BTU rating will heat approximately 700-800
square feet, depending on the unit's efficiency.
From Section Page: Empire Comfort Space Heaters [1]
ID: empire-comfort-space-heaters
Links:
------
[1] http://www.efi...
Our Answer:
We will need the manufacturer and model information before we can
check availability on a replacement blower for your stove. Please
reply with this information and we will be happy to see what we can
find. We look forward to your response...
Our Answer:
The original GFK blower assembly this unit used has now been
discontinued. Unfortunately, the manufacturer does not offer an
equivalent model that you can retrofit in place of the original unit,
as it was a unique, duel blower design that...
Our Answer:
Per the manufacturer, the original blower assembly of 01354 was
replaced with the 01682. This is also a special order item, if you're
interested in it.
From Section Page: Fireplace Accessories [1]
ID: fireplace-accessories
Links:
---...
Our Answer:
Unfortunately, conversion kits for this unit are no longer available.
Martin was purchased by Majestic and their product line was
discontinued.
From Section Page: Fireplace Adaptors & Conversion Kits [1]
ID: fireplace-adaptors---conv...
Our Answer:
Per Monessen, you can indeed replace your Temco BL-1 blower with the
FK12 model [1].
From Section Page: Wood Burning Fireplaces [2]
ID: wood-burning-fireplaces
Links:
------
[1] http://www.efireplacestore.com/maj-fk12.html
[2] http:/...
Our Answer:
Aside from purchasing the original panel directly from a Heatilator
dealer, a universal replacement would be the next best way to proceed.
We offer the Hargrove Replacement Fireplace Refractory Panel - 24 inch
X 28 inch [1] that can be cu...
Our Answer:
Gravity vented furnaces utilize a typical type B-venting system to
draft to the outdoors, which is usually ovalized on the flue outlet to
allow installation in a wall cavity. It will then transition to a
round vent, which will pass throug...
Our Answer:
While we do have universal refractory panels that can replace the
side and back walls, we do not carry a hearth panel for this purpose.
One alternative is to use the original hearth panel as a reference and
create a wooden form to pour a ...
Our Answer:
By your description, it would seem that you have the Honeywell spark
ignition version of this unit. If so, it is possible that either the
flame sensor on the pilot assembly is defective and is not sending a
signal to the valve to light or...
Our Answer:
Simpson Duravent's main Class A product lines are Duratech and
Duraplus. Duratech is a double walled product that has 2" of
difference between the inner and outer walls and is insulated with a
blanket of ceramic fiber. Duraplus is a tripl...
Our Answer:
After checking with the manufacturer, I have learned that this valve
is still in production. However, we do not have a distributor that
carries it or another Maxitrol valve that is a direct replacement. My
recommendation would be to check...
Our Answer:
The only 24\" x 24\" fire pit pan [1] we offer is for a gas fire pit.
We apologize for this inconvenience.
From Section Page: Fire Pit Accessories [2]
ID: fire-pit-accessories
Links:
------
[1] http://www.efireplacestore.com/hpc-571-...
Our Answer:
The 36ECMII was a long running fireplace model that was designed to
be used for wood burning primarily. However, it does have provisions
for installation of a gas line. As such, a gas log lighter or set of
gas logs can also be used. The u...
Our Answer:
Unfortunately, I was unable to find information on your particular
stove, as we are not a dealer for Nu-Tec stoves. However, as a general
rule it is rather difficult and often times impossible to convert a
free-standing wood stove to gas....
Our Answer:
The MBU and MBUC fireplaces are indeed able to be used for gas
burning applications. The units come manufactured with gas line
knockouts made into the chassis of the fireplace, allowing you to
route a 1/2 or 3/4 inch supply line into the ...
Our Answer:
Yes, the Napoleon LHD45 will require electricity to operate, as it
uses it for ignition. There is a battery back-up, however, so you will
be able to use this fireplace in the event of a power outage. Please
let us know if you have any add...
Our Answer:
The original gasket used on this glass was actually a high
temperature adhesive, which is no longer being produced. However, the
adhesive can be carefully scraped away, using an razor knife, then a
3/8 rope gasket can be installed in its ...
Our Answer:
We do not carry refractory panels specifically made for your model.
We do offer universal Hargrove Replacement Fireplace Refractory Panels
[1], though they would likely need to be cut to fit your application.
From Section Page: Firepla...
Our Answer:
While the original doors are no longer available for this unit, the
Majestic Standard Bi-Fold Black Glass Fireplace Doors with Black Track
- For Majestic 42 Inch Royalton Wood Burning Fireplaces [1] can be
used as a retrofit door assembly...
Our Answer:
Unfortunately, no. Most valves have a male threaded bushing that
holds the gas stem in position. The female threads inside the valve
will come factory sealed with teflon tape, pipe sealant, or may use a
gasket of some sort. After removing...
Our Answer:
Typically, unvented fireplaces and decorative logs will last
approximately 20 years when serviced regularly. Buildup of debris in
the main burner orifice, dust or debris clogging the air shutter, and
perforation of the main burner tube ca...
Our Answer:
Yes, you may use the Majestic FK12 Fireplace Fan Kit [1] with your
36BDVRRN. Please see pages 35-36 of this owner's manual [2] for your
unit for more information.
From Section Page: Fireplace Blowers and Fans [3]
ID: fireplace-blower...
Our Answer:
Usually, the control board will have an LED light that will flash to
indicate some sort of fault with the unit. The number of times the LED
flashes, before pausing, will indicate exactly what the issue is.
There is a troubleshooting guide...
Our Answer:
Unfortunately, we do not have the manufacturer-specific panel that
you are looking for, but we do offer some universal refractory panels
that will work for your woodburning fireplace. Please see the
following links: One 24\"h x 28\"w Pane...
Our Answer:
If the fireplace is vented horizontally and has a short run to the
outside wall, the firebox can indeed become cold and radiate some cold
air to the room. However, if the glass is not sealed properly, some
cold air can leak inside as well...
Our Answer:
Unfortunately, we do not have the manufacturer-specific panel that
you are looking for, but we do offer some universal refractory panels
that will work for your woodburning fireplace. Please see the
following links: One 24\"h x 28\"w Pane...
Our Answer:
Yes, we can get the replacement factory brick panels for the WMII-42S
model, as well as a door kit (with a retro-fit kit).
From Section Page: Fireplace Doors [1]
ID: fireplace-doors
Links:
------
[1] http://www.efireplacestore.com/f...
Our Answer:
This will depend on the manufacturer and model of the insert in
question. Some inserts allow for the use of a grate, but it is usually
included as part of the insert itself, while most do not include a
grate and clearly state not to use o...
Our Answer:
Your fireplace can accept the 42GDK line of fireplace doors. These
are available with a black or pewter finish. Please follow the below
link to find the black version. MAJ-42GDKBK [1]. These new style doors
will require an adapter kit to ...
Our Answer:
The main advantages to a single cap are a cleaner look and generally
lower cost overall. It will also eliminate the need for determining
the proper lid size needed for the side by side flues. However, a
single cap can cause back drafting ...
Our Answer:
First, we recommend that you inspect the motor for debris and dust,
and use a can of compressed air to clean out the motor housing. Then,
lay the fan on its back and apply a couple of drops of machine oil to
the motor shaft, near its pene...
Our Answer:
While there was a black door assembly available at one time for this
unit, it was discontinued nearly 10 years ago and the manufacturer
does not produce a direct replacement. Other than having a custom door
assembly fabricated, your best ...
Our Answer:
Superior has now been absorbed by Lennox Hearth Systems. While we do
have universal refractory panels that can be utilized in all brands of
fireplace, I do not carry ceramic liners for the Superior brand. These
units use a particular set ...
Our Answer:
While it is not required by national code, it is definitely a good
idea to tie a chimney liner into your home's grounding electrode
system, especially in areas prone to lightning strikes. You may check
with local code enforcement for more...
Our Answer:
While I am not familiar with your model of fireplace, it may indeed
be possible to replace it with a Breckenridge 42 inch fireplace. The
existing chimney would need to be partially capped at its termination
and the framing would need to b...
Our Answer:
Unfortunately, this manufacturer only produces their trim kit to fit
up to a 12/12 roof pitch. I was not able to locate a manufacturer that
produces a finish plate that will accommodate a 24/12 pitch. It is
likely that you will need to ha...
Our Answer:
A couple of the best options for this type of manufactured fireplace
are the Innsbrook Small Direct Vent Gas Fireplace Insert [1] or the
Napoleon GDIZC Direct Vent Gas Fireplace Insert [2]. Both units are
small enough for installation int...
Our Answer:
Due to harmful chemical residue that can be released from the
fireplace logs and media, it is not recommended for food to come in
contact with the combustion gases.
From Section Page: Fire Pits [1]
ID: fire-pits
Links:
------
[1] htt...
Our Answer:
Per the manufacturer, you can use the Majestic BLOTSC blower [1] in
your HE30 model. You will need to remove the air/blower shield from
the unit and transfer it to your existing mounting brackets for
installation.
From Section Page: Fi...
Our Answer:
We do carry universal refractory panels that can be cut to fit most
models of wood burning fireplace. The suitable panel is the Hargrove
Replacement Fireplace Refractory Panel - 24 inch X 28 inch [1].
Superior was purchased by Lennox Hear...
Our Answer:
Unfortunately, we do not have the manufacturer-specific panel that
you are looking for, as we are not a Lennox/Superior dealer. However,
we do offer some universal refractory panels that will work for your
wood-burning fireplace. Please s...
Our Answer:
The original refractory panels for this model of fireplace have now
been discontinued. Aside from checking with other Majestic dealers for
stock of the panels, my best suggestion would be to use the Hargrove
Replacement Fireplace Refracto...
Our Answer:
We are not a Mendota dealer, but as your insert uses a millivolt
ignition any remote for a millivolt system should work fine. The
SkyTech 3301P Programmable Millivolt Thermostatic Remote Control [1]
is indeed a good choice.
From Sectio...
Our Answer:
Unfortunately replacement parts are not available for vent free log
sets. This is a safety precaution.
From Section Page: Gas Log Valves and Safety Pilots [1]
ID: gas-log-valves-and-safety-pilots
Links:
------
[1]
http://www.efirepl...
Our Answer:
This heater can be used under a covered porch, however a minimum of
36" must be maintained from the top of the heater to the nearest
combustible material of the roof covering.
From Section Page: Patio Heaters [1]
ID: patio-heaters
Li...
Our Answer:
A firebrick liner and refractory firebrick refer to the same thing in
most cases. Both descriptions are usually referring to concrete liner
panels that are stamped and dyed to give the appearance of real
firebrick. On some units, the line...
Our Answer:
Unfortunately, we do not have the manufacturer-specific panel that
you are looking for, but we do offer some universal refractory panels
that will work for your woodburning fireplace. Please see the
following links: One 24\"h x 28\"w Pane...
Our Answer:
Your model appears to be in the line of DFS vent-free units
manufactured by Monessen. If this is the case, unfortunately there is
no conversion kit available as vent-free units cannot be
field-converted. We apologize for this inconvenienc...
Our Answer:
Upon researching this unit, it appears that it is a free standing
direct vent stove. Because of potential sooting and overheating
issues, these units must use the original type of ceramic logs that
they come with. The cast refractory logs...
Our Answer:
In regards to output, rear vent capability, and size of the unit, the
Majestic 36 Inch DVBH Direct Vent Gas Fireplace with Signature Command
Controls [1] is a pretty close match. The unit has a slight size
difference, but reframing would ...
Our Answer:
Superior fireplaces use a proprietary chimney pipe manufactured by
Lennox. Unfortunately, we are not a Lennox dealer and do not have that
information.
From Section Page: DuraTech Class A Chimney Pipe [1]
ID: duratech-class-a-chimney-...
Our Answer:
We do offer a blowout box that could be fitted to your existing pilot
assembly. The part is the Hearth Products Controls Blowout Box
Assembly - For HWI Series Fire Pit Burner Kits [1]. This part is
usually used for Hearth Products Control...
Our Answer:
Unfortunately, we do not carry a manufacturer that offers a rug in
this size. Most of the rectangular rugs measure 22 inches by 44
inches. I apologize that we do not have the size needed.
From Section Page: Hearth Rugs [1]
ID: hearth-...
Our Answer:
Unfortunately, we do not have the manufacturer-specific panel that
you are looking for, but we do offer some universal refractory panels
that will work for your woodburning fireplace. Please see the
following links: One 24\"h x 28\"w Pane...
Our Answer:
Per the owner's manual for the Tuscon 8700 stove, you can use
DuraVent DirectVent Pro pipe, which we carry. However, this must be
used in conjunction with the HearthStone stove starter collar, which
we cannot offer.
From Section Page: ...
Our Answer:
Unfortunately, none of the wood burning inserts we carry have pans.
Some models do exist that have pans, but the manufacturers we carry
opted to keep the unit as short as possible. This eliminated ash pans
from being incorporated into the...
Our Answer:
Has the flame in the fireplace always been very low or is this a
recent development? If the flame has just now become low, there may be
a partial blockage in the gas supply to the valve or the burner.
From Section Page: Majestic Firepl...
Our Answer:
In most cases, there will be enough of a brick ledge behind the doors
to allow the guard to be anchored. However, you will likely need to
remove the door surround in order to mount the smoke guard. Removing
the doors will allow access to ...
Our Answer:
In order to make the transition, an adapter plate will need to be
used in conjunction with a slip connector and chimney liner. The slip
connector will ensure a smooth transition to the adapter plate and to
the manufactured chimney that wi...
Our Answer:
Stainless steel firebacks do a better job of reflecting heat, but
unlike a cast iron fireback, radiate virtually no heat once the fire
has burnt out. Cast iron firebacks will absorb heat during the burn
process and will continue to radiat...
Our Answer:
After checking with the manufacturer, I have learned that the
original and retrofit door assemblies for this unit have now been
discontinued. Unfortunately, I do not have any other doors that could
be used in their place. I sincerely apol...
Our Answer:
While we do not offer a board that has a soft backing, there are
several ways that the board can be modified to protect the floor. If a
board is used that has an R value that meets or exceeds what the stove
requires, you can add rubber or...
Our Answer:
The wool rugs use a chemical treatment that is designed to only allow
the wool material to singe, rather than ignite. We do have many styles
of hearth rugs that are available in other flame retardant materials.
Is there a certain color or...
Our Answer:
Most of our woodburning inserts are meant for installation inside a
masonry/brick fireplace, though some are listed for use within
manufactured units. However, you will need to check with Heatilator to
see if your particular model is appr...
Our Answer:
Yes, the cast iron grates will rust and corrode over time when
exposed to outside air moisture. For outdoor applications, you will
need one of the stainless steel grates. You can narrow your search of
the fireplace grates by clicking the ...
Our Answer:
We do not carry the Ignite-O fire starters.
From Section Page: Fire Starters [1]
ID: fire-starters
Links:
------
[1] http://www.efireplacestore.com/fire-starters.html
Our Answer:
It is a bit difficult to find replacement components for the Temco
line. This is due to their going out of production several years ago.
However, their parent company, CFM, was absorbed by Majestic. As such,
there is a chance that there i...
Our Answer:
The gas log sets we carry are available in both natural gas and LP.
In order to narrow down to the correct fuel type, you will first need
to select the "vented" or "ventless" gas log category. You may then
narrow down your selections by f...
Our Answer:
We are in sales only of our products. The gas log assembly would need
to be installed by a local plumber or HVAC technician.
From Section Page: Vented Gas Logs [1]
ID: vented-gas-logs
Links:
------
[1] http://www.efireplacestore.com/...
Our Answer:
Most of our items can indeed be shipped to Alaska. Please contact us
[1] with the desired item number(s) and your zip code and we will be
happy to provide a shipping quote. We look forward to your response.
From Section Page: Wood Burn...
Our Answer:
Yes, the cap needed for your FMI 36ECMII is still available. You can
see your options below: FMI Wood Fireplace Large Round Top with
Louvered Screen for FMI 8 Inch Diameter Woodburning Chimney Venting
Pipe [1] FMI Wood Fireplace Round Chi...
Our Answer:
Per the manufacturer, the surround and louvers were specific to this
model. The current GI3600 is close in design, but not an exact match
to this unit. As such, the surround and louvers would need to be
painted. This can be done by removi...
Our Answer:
One of our more popular options for this style and finish is the
Gallery Vintage Iron Glass Fireplace Door Assembly - 46 Inch x 26 Inch
[1]. This assembly is designed to cover an opening of your dimensions
and has sufficient overlap for t...
Our Answer:
Unfortunately, we do not have the manufacturer-specific panel that
you are looking for, but we do offer some universal refractory panels
that will work for your woodburning fireplace. Please see the
following links: One 24\"h x 28\"w Pane...
Our Answer:
The use of a grate is completely up to you. Grates do aide in air
circulation which can lend to easier starting fires. However,
traditional inserts, those full-bodied appliances that are installed
into masonry fireplaces, do not normally ...
Our Answer:
Unfortunately, we do not have the manufacturer-specific panel that
you are looking for, but we do offer some universal refractory panels
that will work for your wood-burning fireplace. Please see the
following links: One 24\"h x 28\"w Pan...
Our Answer:
Unfortunately, we do not have the manufacturer-specific panel that
you are looking for, but we do offer some universal refractory panels
that will work for your wood-burning fireplace: One 24\"h x 28\"w
Panel [1] Two 24\" h x 40\"w Panels...
Our Answer:
Unfortunately, no. None of our gas log sets are suitable for use
within a direct vent fireplace such as yours. Your only option would
be a replacement burner/log set that is identical to the one that came
with the unit, if it is still ava...
Our Answer:
Unfortunately, we do not have the manufacturer-specific panel that
you are looking for, but we do offer some universal refractory panels
that will work for your woodburning fireplace. Please see the
following links: One 24\"h x 28\"w Pane...
Our Answer:
While newspaper can make for good kindling, we do not recommend only
burning paper in a woodburning insert. These are designed to burn only
real wood.
From Section Page: Wood Burning Fireplace Inserts [1]
ID: wood-burning-fireplace-i...
Our Answer:
Yes; after prolonged use, the motor may indeed need to be oiled on
the Ecofans.
From Section Page: Caframo Ecofans Wood & Gas Stove Fans [1]
ID: caframo-ecofans-wood---gas-stove-fans
Links:
------
[1]
http://www.efireplacestore.com/...
Our Answer:
I will be happy to check into availability of a conversion kit for
your fireplace. The electronic ignition version of this fireplace used
either a Honeywell or SIT brand gas valve. Please advise which valve
your unit has installed. The br...
Our Answer:
It is possible to use a fireplace insert in some models of prefab
fireplaces, but it will depend on the brand and model of the prefab
unit itself. If you would like to give us a call at 1-800-203-1642, we
can determine if your unit would ...
Our Answer:
Per national code, the termination for a conventional pellet vent
appliance cannot be closer than 4 feet to a door or window. Please be
sure to check with your local code office, as they may have a
different requirement. Local jurisdictio...
Our Answer:
We do carry Selkirk's line of Class A chimney pipe. The Supervent 7"
is a lower quality builder grade pipe, while the interchangeable
SuperPro 8" diameter pipe can be found here [1] available in different
lengths varying from 6" to 48".
...
Our Answer:
Yes, you will need this Monessen BLOTS blower [1] for your CSVF-30
stove.
From Section Page: Fireplace Blowers and Fans [2]
ID: fireplace-blowers-and-fans
Links:
------
[1] http://www.efireplacestore.com/movathcofoai2.html
[2] http:...
Our Answer:
Since there are no 45-degree elbows made in Class A chimney pipe,
yes, you will need to run your stovepipe out the wall at a 90-degree
angle and use a Class A tee to turn the pipe vertically outside the
home to run up over the roof.
Fr...
Our Answer:
This unit uses FMI 8DM venting components. Please visit the item page
for the CUI-VC42LI1 [1]. You can then see the correct venting
components by clicking the "venting components" tab on the item page.
From Section Page: Class A Chimney...
Our Answer:
The proper fan for this particular unit is this item: Wood-Burning
Fireplace Fan [1] The fan will need to be positioned in the bottom of
the fireplace, at the very back of the void space under the firebox
floor. There is a removable panel...
Our Answer:
Unfortunately, we do not have the manufacturer-specific panel that
you are looking for, but we do offer some universal refractory panels
that will work for any wood-burning fireplace. Please see the
following links: One 24\" h x 28\" w Pa...
Our Answer:
Unfortunately, we do not have the manufacturer-specific panel that
you are looking for, but we do offer some universal refractory panels
that will work for your woodburning fireplace. Please see the
following links: One 24\"h x 28\"w Pane...
Our Answer:
While we do carry sliding pull screens, we do not offer a screen
assembly that rolls up.
From Section Page: Fireplace Screens [1]
ID: fireplace-screens
Links:
------
[1] http://www.efireplacestore.com/fireplace-screens.html
Our Answer:
We are a Napoleon dealer and we can supply the factory replacement
part(s) you need. For your NPS45, there are three separate parts
applicable: (1) igniter, (2) igniter housing and (3) igniter gasket.
From Section Page: Stove Accessori...
Our Answer:
The Country Hearth line of wood stoves by US Stove are both 50 state
EPA certified and can be used in a manufactured home. An example is
the US Stove Medium EPA-Certified Wood-Burning Stove [1]. We also
offer units with higher BTU output,...
Our Answer:
Polished brass surrounds, such as your fireplace enclosure, can be
tricky to paint. These types of high luster surfaces must be sanded
with a fine grit sandpaper prior to being painted, in order to get the
paint to stick. A 150 grit paper...
Our Answer:
All of our high-heat paint will peel if subjected to the temperatures
achieved inside of a wood burning fireplace. If you have a gas
fireplace, the paint will hold up considerably better. Please reply
with your application and we may be a...
Our Answer:
Unfortunately, no. All of our blowers are model-specific and we do
not carry one for this particular model. We apologize for the
inconvenience.
From Section Page: Fireplace Insert Blowers and Fans [1]
ID: fireplace-insert-blowers-and...
Our Answer:
The RCMT remote is an on/off model that includes a delay timer and
temperature display. The RCST has most of the same functions but
replaces the time with a programmable thermostat function, allowing
the remote to automatically cycle the ...
Our Answer:
You can reach Selkirk (the manufacturer of the SuperVent pipe) at
1-800-992-8368.
From Section Page: SuperVent Class A Chimney Pipe [1]
ID: supervent-class-a-chimney-pipe
Links:
------
[1] http://www.efireplacestore.com/supervent-cla...
Our Answer:
None of our rugs are made to cut. Doing so would compromise the
integrity of the rug as well as void the warranty.
From Section Page: Hearth Rugs [1]
ID: hearth-rugs
Links:
------
[1] http://www.efireplacestore.com/hearth-rugs.html
Our Answer:
There are two blower options for your Napoleon GD36NTR fireplace [1].
The B440-KT blower [2] has a rating of 80 CFM (cubic feet per minute
of circulation) and a one-year manufacturer's warranty. The GZ550-1KT
blower [3] has a rating of 10...
Our Answer:
In order to ensure that a vented gas log set is as quiet as possible,
the following steps must be taken: 1. Ensure that the gas supply line
is properly sized for the BTU needs of the appliance. The supplied
flex line should not have any s...
Our Answer:
Unfortunately, we do not carry a high temperature paint that is this
exact color. We do have several shades of green paint, but they are
much darker or lighter than the shade you are looking for. Our Emerald
Green Stovebright Paint [1] wi...
Our Answer:
While we do not have any doors made specifically for your fireplace,
we do have several styles of "bolt-on" door assemblies. Please follow
the link below to find a door that will fit your fireplace dimensions.
Any of the kits by Portland-...
Our Answer:
We do offer a couple of Rumford style fireplace screens, such as the
Pilgrim Traditional Rumford Fireplace Spark Guard - 44 Inch x 43 Inch
[1]. Any other style of screen would need to be custom made, as your
42 inch opening is beyond the ...
Our Answer:
While the original blower for your model is no longer available, the
Majestic FK12 Fireplace Fan Kit [1] will work with your model,
according to the manufacturer.
From Section Page: Fireplace Blowers and Fans [2]
ID: fireplace-blower...
Our Answer:
We have numerous natural gas units in both direct vent and vent-free
that will indeed function in the event of a power outage. These are
fireplaces that have a millivolt ignition system. This pilot system
has a small flame that generates ...
Our Answer:
Yes, for a tool set that will be left outdoors, we recommend the
UniFlame 5-Piece Stainless Steel Indoor/Outdoor Fireplace Tool Set
[1].
From Section Page: Fireplace Accessories [2]
ID: fireplace-accessories
Links:
------
[1] http:/...
Our Answer:
Because of the potential dangers that can occur from incorrect
conversion, most manufacturers do not allow field conversion or
produce conversion kits for vent free appliances. I have checked the
manufacturer information for both of these...
Our Answer:
Unfortunately, no. Our decorative valve covers are designed to thread
onto any standard, 1-inch gas valve body.
From Section Page: Fireplace Keys and Valves [1]
ID: fireplace-keys-and-valves
Links:
------
[1] http://www.efireplacesto...
Our Answer:
While not an exact match, the Stovebright Almond [1] paint will be
the closest color we have to match the Vermont Castings enamel.
From Section Page: Stove Bright Paint [2]
ID: stove-bright-paint
Links:
------
[1] http://www.efirepla...
Our Answer:
Building the fireplace into the entertainment center is certainly
feasible, as long as the required clearances are maintained between
the box and the surrounding wooden enclosure. A couple of our more
popular and reliable models are manuf...
Our Answer:
Unfortunately, we do not have the manufacturer-specific panel that
you are looking for, but we do offer some universal refractory panels
that will work for your wood-burning fireplace: One 24\"h x 28\"w
Panel [1] Two 24\" h x 40\"w Panels...
Our Answer:
We have confirmed with FMI that the cabinet doors and end panel are
still available for the PN36 in black (with brass trim), brushed brass
and chrome (platinum) finishes. Please reply with your shipping zip
code and we can provide pricing...
Our Answer:
Most wood-burning units have provisions to install gas logs. However,
removing the entire unit in order to install a direct vent fireplace
would be a different affair. Depending on the model and manufacturer
of the existing wood burning f...
Our Answer:
We have many 36" vent-free fireboxes from a few different
manufacturers. One of our most popular is the 36\" Monessen Universal
Circulating/Radiant Vent-Free Firebox with Refractory Brick Liner [1]
has an actual 36" front width opening, a...
Our Answer:
My apologizes, but every wood burning insert that we currently offer
measures between 21 to 23 inches in height. If your EC36 has a metal
smoke shelf at the front that is removable, you may be able to gain
more height that way. However, i...
Our Answer:
Unfortunately, a fan kit is not able to be used with the GL4000E/EP.
Unlike the GL4100, this model does not have provisions for the kit to
be installed, as it is lacking the blower compartment and louvers that
are needed to circulate air....
Our Answer:
Generally speaking, no. California has outlawed the use of vent-free
gas appliances in most applications. Please contact your local
building code enforcement office for more information.
From Section Page: Vent Free Fireplaces [1]
ID...
Our Answer:
If you are installing a stove closer than the manufacturer
requirements to the ceiling, a heat resistant wall board will indeed
be needed. The product we offer for this purpose is the SBI Micore-300
Mineral Fiber Board - Pack of Four [1]....
Our Answer:
The Napoleon GVF36 [1] is a great vent free option. It is a clean
burning, attractive unit and is capable of producing 30,000 BTU, which
is enough to heat more than 800 square feet.
From Section Page: Empire Fireplace Inserts [2]
ID:...
Our Answer:
Most vent free fireplaces are unable to use doors, as they need to be
able to readily convect heated air to the room. However, most units
will have a safety screen that is placed over the opening in order to
serve as a protective barrier....
Our Answer:
Because this is an older, discontinued line of fireplace, the
original panels are no longer available. Instead, a universal set of
refractory panels must be cut to fit. Our most popular kit is the
Hargrove Replacement Fireplace Refractory...
Our Answer:
Unfortunately, we do not currently carry this fireplace. It is simply
no longer available. However, we do have alternative products
available. Probably the closest option we carry to the 36BDVR would be
our CDVR36PV7: Monessen 36 Inch CDV...
Our Answer:
The Rutland PB-6P50 is indeed the correct type of brush for sweeping
a metal chimney and will fit most standard 3/8" threaded rods. For a
once a year cleaning, the Rutland Heavy-Duty Fiberglass Chimney Rod -
5 Foot [1] would be excellent ...
Our Answer:
Yes, for the most part, all gel fuel fireplaces are a stepped down
version of larger units. The largest units we offer are likely the
type that come with mantels. Unfortunately, our gel fuel appliances
are produced no taller than 42" with...
Our Answer:
Yes, we have a variety of see-thru (two-sided) gas log sets,
available in both vented and ventless configurations. You can see all
of them here [1].
From Section Page: Gas Logs [2]
ID: gas-logs
Links:
------
[1] http://www.efireplac...
Our Answer:
Unfortunately, no vent-free gas appliance can be field converted. We
apologize for this inconvenience.
From Section Page: Gas Fireplace Inserts [1]
ID: gas-fireplace-inserts
Links:
------
[1] http://www.efireplacestore.com/gas-firep...
Our Answer:
Yes. Per the manufacturer, you can use the 42GDKBK [1] doors with a
retro-fit kit. The fit kit is not available on our website, but we can
provide a quote to special order the doors and the kit you would need.
From Section Page: Majest...
Our Answer:
From your description, is sounds like the Majestic 36GDK door
assembly is required for your unit, as it measures 35 7/8 inches wide
and 21 7/16 inches tall. The assembly attaches to the front fireplace
weldment, via the predrilled holes. ...
Our Answer:
I am assuming you are referring to the shut off valve? If so, yes it
can be relocated. However, it will require cutting into the wall and
cutting/threading the pipe, which can indeed be an undertaking.
From Section Page: Fireplace Keys ...
Our Answer:
We do indeed carry the Empire Automatic Blower for Heritage Cast Iron
Gas Stoves [1]. This blower is a direct fit for the entire Empire
Heritage line of stoves.
From Section Page: Empire Wood Stoves [2]
ID: empire-wood-stoves
Links:
...
Our Answer:
For lighting instructions for the Majestic NVBC36, please refer to
the owner's manual here [1].
From Section Page: Majestic Fireplaces [2]
ID: majestic-fireplaces
Links:
------
[1]
http://literature.mhsc.com/archive/majestic/NVBR_C36...
Our Answer:
Oiling can be accomplished by laying the fan on its back and applying
a couple of drops of machine oil to the motor shaft, near its
penetration to the motor housing. Once this is done, re-assemble the
fan and test it. If this does not sol...
Our Answer:
Some models of fireplaces, including this model, do not allow for use
of ventless gas logs because they are not insulated to stand up
against the extra heat. Because the damper is closed during operation
of ventless gas logs, no dilution ...
Our Answer:
There are two available blowers for your Solitaire direct vent, and
the one you need will depend on your ignition system. If you have the
Signature Command System (electronic ignition), you will need this
blower: Majestic BLOTBLDVSC Signa...
Our Answer:
Vented gas logs must use a functional existing chimney (either a clay
flue within a masonry chimney or a manufactured metal Class A chimney
pipe). They are burned with the flue open and cannot be used unless
you have a masonry fireplace o...
Our Answer:
While we do offer Class A chimney that has a 12 inch I.D., the
largest stovepipe we carry is 10 inches in diameter. I am unaware of a
company that currently manufactures single walled stovepipe in excess
of 10 inches in diameter. I apolog...
Our Answer:
The next step would be to check pressure at the inlet/outlet gas
pressure taps on the valve itself. Older valves can become sensitive
to gas pressure changes. Incoming manifold pressure should be between
5 and 10.5 inches of W.C. when tes...
Our Answer:
We have several bifold door assemblies that come complete with an
inner sliding mesh screen. One such item that would fit the dimensions
of your fireplace would be this item [1].
From Section Page: Fireplace Specific Fireplace Doors an...
Our Answer:
While we do not carry panels for the Superior brand of fireplaces, we
do have universal panels that can be cut to fit. If the unit does
indeed have concrete refractory panels, you may use either the
Hargrove Replacement Fireplace Refracto...
Our Answer:
None of our vent-free fireplaces offer the ability to have a sealed
glass front or glass door assembly. This is due to the nature of
vent-free gas appliances; they must be open to the room in order to
"breathe," as there is, of course, no...
Our Answer:
You will need the appropriate venting components for your stove,
which will either be B-Vent pipe or direct vent pipe. Please reply
with the manufacturer and model number of your stove and we can
provide additional information regarding w...
Our Answer:
The basic principle separating the two types of gas logs is that
vented gas logs require some means of venting the combustion
by-products and exhaust resulting from the burning of any kind of
fuel, and ventless or vent-free gas logs do no...
Our Answer:
We do sell the VR-1A remote, but we only offer it complete with
receiver and hand-held transmitter. You can see the item here: VR-1A
remote [1]. Please let us know if you have any additional questions.
From Section Page: Gas Log Valves ...
Our Answer:
Per the manufacturer, this line of piping does not carry a specific
heat rating. However, they did indicate that the product is designed
for use with Class A, non HT types of chimneys, which have a 1700
degree heat rating.
From Section ...
Our Answer:
Parts for this unit have indeed been discontinued. The 43BDVR was
manufactured by the CFM Corporation, which owned Majestic up until
2008, when they declared bankruptcy. The product line was not picked
up by the new owner of Majestic. Unf...
Our Answer:
It is likely that the glass pebbles cannot be returned to their
original color, as the soda likely cooled them rapidly, causing
contraction and the residue to be drawn into the glass. You may try
soaking the pebbles in a tub of glass clea...
Our Answer:
The Cascade brand of screen is indeed a higher quality choice. A
thicker gauge of steel wire is used in the manufacture of the Cascade
line of products. Because of this, they will have superior longevity
in most applications.
From Secti...
Our Answer:
Unfortunately, all of our stove paint is designed for use on heating
appliances and not on cooking appliances. Indeed, we do not currently
offer any paint that is rated for cooking appliances.
From Section Page: Stove Paint & Fireplace ...
Our Answer:
This firebox is intended for B-vent gas burning applications only. It
is also intended to be used as an enclosure for any of the Victorian
Hearth decorative surrounds/facings. The decorative surrounds push
back into the 301 firebox, which...
Our Answer:
The 1450 is an EPA type stove, which uses internal ceramic baffles,
secondary air tubes, and an insulation blanket to limit the amount of
heat that escapes to the chimney. These items, in conjunction with the
air control lever, eliminate ...
Our Answer:
We have a couple of options for your situation. First, if you have
the model and manufacturer of your unit, we can check availability for
a replacement panel for your unit. If you cannot get that information,
we do have some universal rep...
Our Answer:
The original Temco fan is no longer available, however the Majestic
FK12 Fireplace Fan Kit [1] is a direct replacement for this unit.
Unfortunately, we are no longer able to obtain the Temco chimney line,
as our last supplier of their chi...
Our Answer:
Please see the following description from our website: Here is a
brief explanation of what to consider when purchasing gas logs for
your fireplace. Vented Gas Logs - Vented gas logs are to be used with
an open chimney flue or damper. The ...
Our Answer:
Yes, we have a few different Real Fyre propane ventless log sets that
feature an electronic pilot kit and the option to add a remote
control. Please reply with your fireplace dimensions (front width,
rear width, depth), and we can make a ...
Our Answer:
Some inserts advise against using a grate, and yours may fall into
this category. Please check with the manufacturer for more
information.
From Section Page: Fireplace Grates [1]
ID: grates
Links:
------
[1] http://www.efireplacesto...
Our Answer:
Generally, we would need to know the available width, height, and
depth of the space that you plan on building the fireplace into. This
will allow us to suggest a unit with framing dimensions that are close
to your needs.
From Section P...
Our Answer:
Per the manufacturer, this assembly has been discontinued and stock
of the item is no longer available. My recommendation is to continue
checking with other Majestic dealers to see if they may have this
replacement still in stock. Another...
Our Answer:
While we do not offer any specialty paints that can withstand the
temperatures of a woodburning fire, we do have options if you are
using gas. Please see these recommendations for painting the interior
of your fireplace: Copperfield Black...
Our Answer:
Unfortunately, we have zero 9" offerings. If you have 9" pipe
currently, it is recommended to stay with that diameter of pipe. It is
not advised to increase or decrease from existing pipe.
From Section Page: Stove Pipe [1]
ID: stove-p...
Our Answer:
This item is indeed designed to be flame resistant and will smolder
no further than 3 inches in any direction from the contact point of a
hot ember. The backing will not allow the ember to burn completely
through the rug.
From Section P...
Our Answer:
Upon researching the information you provided, this model number is
for the log set only which is no longer manufactured. In order to
replace the existing set, you would need to purchase a complete new
log set and burner system. The fireb...
Our Answer:
An indoor/outdoor fireplace will indeed give off a limited amount of
heat on the outdoor side. However, the unit is primarily intended to
viewing aesthetics, as the sealed outdoor conversion window limits a
great deal of heat from being t...
Our Answer:
Brands of double wall chimney pipe are not interchangeable, due to
the proprietary locking tabs found on the ends of the chimney pipe.
Further, we do not currently carry Hart & Cooley chimney components.
We apologize for the inconvenience...
Our Answer:
Depending on your unit, there are a few places the manufacturer
information may be located. The first location would be a metal plate
that is on the left or right side of the smoke shelf bracket, right at
the top of the fireplace front op...
Our Answer:
The key required will depend on the fireplace. Do you have the model
number of the fireplace installed? Is this a wood-burning unit with a
gas starter or a gas unit?
From Section Page: Fireplace Keys and Valves [1]
ID: fireplace-keys...
Our Answer:
The maximum allowed horizontal run for any B-vent fireplace will
depend on the manufacturer's requirements for the specific model being
vented. This information will be listed in the owner's manual.
From Section Page: B-Vent Fireplaces...
Our Answer:
The largest linear fireplace we currently carry is the Napoleon 62\"
Linear Direct Vent Natural Gas Fireplace - 50,000 BTU [1]. This unit
features a viewing area of approximately 62 inches and a framing area
of 81 inches to accommodate th...
Our Answer:
In order for the unit to vent properly, you must use a flexible
chimney liner of the proper size and route it to the bottom of the
first clay flue tile. Ideally, the liner would run the entire length
of the chimney, as this would greatly ...
Our Answer:
Monessen DFS vent-free fireplace systems use the BLOTMC Forced Air
Fireplace and Firebox Blower with Variable Thermostat Control [1].
From Section Page: Fireplace Insert Blowers and Fans [2]
ID: fireplace-insert-blowers-and-fans
Lin...
Our Answer:
I have not come across a brand that does not use a fan to help
convect the heat. Because the heating element is sealed inside the
unit, the fan is necessary to push heat from within the casing into
the room. Many models exist that allow t...
Our Answer:
The patio heaters are intended to be used in a non-covered area.
From Section Page: Patio Heaters [1]
ID: patio-heaters
Links:
------
[1] http://www.efireplacestore.com/patio-heaters.html
Our Answer:
Any push-in type of 6 inch cap for factory built chimneys will work.
Selkirk's SuperPro line also uses the same type of twist lock
mechanism as their Supervent line. As such, this SuperPro All-Fuel
Deluxe Chimney Rain Cap [1] would offer ...
Our Answer:
Per the manufacturer's literature for this appliance, it is an
unvented fireplace. Unfortunately, unvented or vent free appliances
cannot be converted from one gas type to another. There is no
conversion kit available to modify this unit....
Our Answer:
While not an exact fit, the BM0037 is definitely the closer adapter
to fitting your needs. The BM0039 will definitely be too large.
Because the oval on your stove is not a standard size, the adapter may
need to be modified slightly to fit...
Our Answer:
The CFX32 model uses the Monessen BLOT Variable Thermostat Controlled
Forced Air Blower [1].
From Section Page: Majestic Fireplaces [2]
ID: majestic-fireplaces
Links:
------
[1] http://www.efireplacestore.com/cui-blot.html
[2] http:...
Our Answer:
While we do not offer any components to transition from your clay
flue to single-wall stovepipe, we do offer some for going to a
double-wall Class A chimney pipe. You would use an anchor plate that
would be installed on top of your masonr...
Our Answer:
Typically, open-faced inefficient wood-burning fireplaces such as the
Vantage Hearth Value Line series are not permitted for installation in
California. We recommend checking with your local building inspector
to be sure.
From Section ...
Our Answer:
For instances when small insects are a nuisance, I recommend wrapping
the factory chimney mesh with a smaller gauge stainless steel wire
mesh. So as not to impede draft, I do not recommend going smaller than
1/8 of an inch.
From Sectio...
Our Answer:
Please allow us to check with the manufacturer regarding availability
of a replacement panel for this unit. If it is available, it will take
about 4-6 weeks to ship to you. If you are still interested, please
reply with your shipping zip ...
Our Answer:
A hood can indeed serve as a good way to protect your mantel from
damage. The projection of the hood will depend on how much space is
between the fireplace opening and the mantel. Projection of the mantel
will also be key.
From Section ...
Our Answer:
A blower is intended to circulate heated air into the room from the
fireplace, rather than to assist in drafting issues. In your scenario,
it would be necessary to extend the chimney to alleviate the pressure
issue caused by the wind. If ...
Our Answer:
Unfortunately, we do not offer a color close to the oil-rubbed bronze
that you desire. We apologize for this inconvenience.
From Section Page: Stove Paint & Fireplace Paint [1]
ID: paint
Links:
------
[1] http://www.efireplacestore....
Our Answer:
If "VC" refers to Vermont Castings, Stove Bright makes a gas vent
pipe paint that specifically matches the black Vermont Castings
stoves. Please see it below: Stove Bright Vermont Castings Black Gas
Vent Paint - 43121 [1]
From Section P...
Our Answer:
You can usually find ethanol under the name "denatured alcohol" at
your local hardware store.
From Section Page: Ethanol Fireplaces [1]
ID: ethanol-fireplaces
Links:
------
[1] http://www.efireplacestore.com/ethanol-fireplaces.html
Our Answer:
No, you would need to replace the entire fireplace and chimney in
order to burn wood. You can see our full selection of zero-clearance
woodburning fireplaces below: Wood Burning Fireplaces [1]
From Section Page: Fireplace Inserts [2]
...
Our Answer:
Yes, the FMI CD36RN direct vent fireplace uses the BK model
squirrel-cage blower. You can see it at the following link: FMI Rotary
Type Fan Blower with Magnetic Attachment [1].
From Section Page: Fireplace Blowers and Fans [2]
ID: fir...
Our Answer:
It is quite likely that the draft of your fireplace is weak to begin
with and the cap is simply enough to stifle what little draft there
is. There are a couple of things that could cause this. 1. The chimney
cap screen height is too short...
Our Answer:
The manufacturer has informed us that replacement panels are no
longer available. We do not offer any universal replacements suitable
for your fireplace. We apologize for the inconvenience.
From Section Page: Fireplace Panels and Liner...
Our Answer:
We would be happy to help you find a replacement gas log set. You can
see our full selection here: Gas Logs [1] To further assist you,
please reply with the dimensions of your fireplace, including front
width, rear width and depth. Also, ...
Our Answer:
If you need chimney pipe or stove pipe and are not sure exactly what
you need, please complete the Chimney Pipe Design & Quote Form [1].
One of our fireplace specialists will design your chimney installation
for you. We will send you a qu...
Our Answer:
I would suggest using a semi-gloss acrylic paint. A high heat paint
is not necessary.
From Section Page: Stove Paint & Fireplace Paint [1]
ID: paint
Links:
------
[1] http://www.efireplacestore.com/paint.html
Our Answer:
The shut-off valve can be close to the firebox, but not inside it.
Usually it is placed on the wall next to the fireplace opening in the
floor on the hearth of the fireplace.
From Section Page: Fireplace Keys and Valves [1]
ID: firep...
Our Answer:
Unfortunately, the smallest doors we have are for 27" widths. We
recommend looking for a manufacturer that offers customized doors for
an opening sized opening.
From Section Page: Fireplace Doors [1]
ID: fireplace-doors
Links:
-----...
Our Answer:
Unfortunately, no, we have no such piece. The only 22-gauge piece
that is close to what you need is a 8" female to 6" male: 8\" female
to 6\" pipe. [1]
From Section Page: Heat-Fab Stove Pipe [2]
ID: heat-fab-stove-pipe
Links:
------
...
Our Answer:
If local codes permit it, you can install one of these zero clearance
vent-free fireplaces. You may prefer a direct vent fireplace, however.
For more information please see our Gas Fireplace and Stove Buying
Guide [1].
From Section Pag...
Our Answer:
Because of the close proximity to the fireplace, it would be best to
use metal masonry anchors to attach the screen. These anchors, in
conjunction with "L" brackets should be adequate to support the
screen.
From Section Page: Fireplace ...
Our Answer:
Yes, that line of models was discontinued by Majestic. We do offer
several similar models, such as these: Majestic 36 Inch DVB Direct
Vent Gas Fireplace with Signature Command Controls - Natural Gas [1]
Monessen 36 Inch CDV Direct Vent Ga...
Our Answer:
Many of the open faced models we carry can be equipped with a log
lighter, however they are not an efficient source of supplemental
heat. They do offer a blower to supplement circulation, but do not
have a forced air heating option. All s...
Our Answer:
If the fireplace can be located above grade, then the fireplace and
chimney system could be enclosed in a decorative chase along the
exterior of the home. However, if the fireplace is to be located below
grade, the unit would need to be f...
Our Answer:
Ceramic refractory panels are only suitable for installation in a gas
fireplace. Any biomass type of fireplace or stove will overheat the
panels and cause them to deteriorate rapidly. You may be able to find
a concrete refractory panel th...
Our Answer:
Because of the increased humidity and air circulation in an outdoor
environment, a circulating blower is not used on these units. Instead,
natural radiation and convection is used to circulate heat.
From Section Page: Patio Fireplaces [...
Our Answer:
You have two options for a blower, and the one you choose will depend
on how you want to control the fan. Please see them below: Majestic
BLOT Variable Thermostat Forced Air Fireplace Blower [1] This is a
thermostatically-controlled blowe...
Our Answer:
It is likely you could use either a rigid or flexible B-vent pipe to
accomplish this, but it must be one of the two. B-vent piping has a
dual wall setup and would be needed for proper clearances. We carry a
large line of B-vent piping man...
Our Answer:
Yes, generally you would call a plumber and have him run a gas line
to your masonry/brick or manufactured (steel) fireplace. If you have a
manufactured unit, you would need to make sure that it is tested and
listed for gas logs.
From S...
Our Answer:
When burning firewood with very frequent usage, typically a
heavy-duty steel grate with thick bars is recommended. Cast iron
grates allow for burning wood or coal.
From Section Page: Fireplace Grates [1]
ID: grates
Links:
------
[1]...
Our Answer:
It is standard for factory-built wood-burning fireplaces to use Class
A vent pipe. Most of these models will use an air cooled variety of
Class A that has a four- to five-inch difference between the inner and
outer walls.
From Section ...
Our Answer:
BTU is an acronym for "British thermal unit", and it is a measurement
of heat produced by burning fuel. The general rule of thumb is 35 BTUs
heats one square foot; therefore 35,000 BTUs = 1,000 square feet of
heating area.
From Section...
Our Answer:
Yes, the SC36 is a wood-burning fireplace that is designed to burn
wood. As such, if all gas components are removed, you can indeed burn
wood in the unit, provided the Class A chimney system is in good
shape.
From Section Page: Gas Fir...
Our Answer:
Most installations will require the use of a gas regulator, flexible
connector, and nipple to connect to the propane valve. However, the
type of regulator and size of the line will depend entirely on the
fireplace. There should be a chart...
Our Answer:
For clarification, do you have a masonry/brick fireplace, or a
manufactured (metal) fireplace? Are you looking to install a
wood-burning insert, a gas insert, or a gas log set? Also, please
provide the fireplace dimensions so we can offer...
Our Answer:
The closest screen that I carry in regards to style and dimensions
needed is the Pilgrim Traditional Rumford Fireplace Spark Guard - 50
Inch x 49 Inch [1]. Unfortunately, I do not have any other models that
have the 50 inch width and nece...
Our Answer:
You would only be able to convert to a natural gas appliance if the
log set and burner assembly are separate from the Desa firebox in
which they are installed. If firebox, burner and logs are one
comprehensive assembly, conversion to a ne...
Our Answer:
A factory replacement screen assembly would be needed for your
manufactured fireplace. You could paint the fireplace using some
high-heat fireplace paint.This is would work for a gas fireplace, but
not a woodburning unit.
From Section ...
Our Answer:
A louvered model will have slat louvers at the top and bottom of the
fireplace allowing air to circulate around the chassis of the firebox.
Most commonly, louvered models also allow use of a blower. A flush
fireplace will not have the lou...
Our Answer:
Yes, we have woodburning fireplaces larger than 42". Please see our
full selection below, then utilize the search features on the
left-hand side of the page to see our biggest models: Wood Burning
Fireplaces [1]
From Section Page: Firep...
Our Answer:
My apologies, but I was unable to find any reference to this vent in
the owner's manual for this fireplace. While the unit has knockouts
for a gas line on either side of the unit, these are down low inside
the box. Would it be possible to...
Our Answer:
We have plenty of options for you. Please see our full selection
here: Hearth Boards & Stove Boards [1]
From Section Page: Wood Stoves [2]
ID: wood-stoves
Links:
------
[1] http://www.efireplacestore.com/hearth-boards.html
[2] http:...
Our Answer:
While we do carry a variety of ventless propane gas logs, none of
them have a blower option. You can see our full selection of ventless
log sets below: Ventless Gas Logs [1]
From Section Page: Gas Logs [2]
ID: gas-logs
Links:
------...
Our Answer:
My apologies, but we no longer carry the Copperfield wood cart with
canvas liner included. Currently, the canvas is sold individually as
the Pilgrim Heavy-Duty Canvas Wood Cart Liner - For Pilgrim Forged
Iron Wood Carts [1]. This canvas i...
Our Answer:
While we do not have an item that features the doors mounting the far
edges of the frame, we do offer a similar item, such as the Pilgrim
Vintage Iron Fireplace Screen with Full-Height Doors [1].
From Section Page: Mesh Fireplace Scree...
Our Answer:
I believe you are referring to Malm fireplaces. Unfortunately, we do
not offer any models similar to those.
From Section Page: Fireplaces [1]
ID: fireplaces
Links:
------
[1] http://www.efireplacestore.com/fireplaces.html
Our Answer:
From your description, a 24 inch fire ring could indeed be used for
your installation. If you are looking for the highest flame possible,
you will likely be interested in going with our Hearth Products
Controls Round Stainless Steel High-...
Our Answer:
Your G45-20 burner can indeed utilize an SPK-26N in place of the
EPK-1. Please see it on our website below: Real Fyre SPK-26 Safety
Pilot Kit for Natural Gas Logs [1]
From Section Page: Gas Log Burners Only [2]
ID: gas-log-burners-onl...
Our Answer:
If you have a masonry fireplace, you will need to purchase a door
assembly that is slightly larger. Most door assemblies that fit a 30 x
36 opening will measure 33-34 inches tall and 38-40 inches wide. This
allows the space needed to moun...
Our Answer:
Unfortunately, this mantel can only be used with the specified gas
fireplaces that are mentioned in the item description. Due to the
combustible nature of the mantel, it is not listed by Napoleon for use
with a true wood burning fireplace...
Our Answer:
If your fireplace is a FMI/DESA model DVF36, you can use either of
these two blowers: FMI Rotary Type Fan Blower with Magnetic Attachment
[1]. FMI Thermal/Rheostat Controlled Squirrel Cage Type Blower [2].
From Section Page: Fireplace I...
Our Answer:
Unfortunately, we are not a dealer for the master flame series of
logs. As such, we do not carry the appropriate conversion kit. I
recommend visiting the manufacturer website to locate a dealer that
may offer the conversion kit. The manuf...
Our Answer:
Yes we do, and you can view it at the following link: Variable Speed
Blower [1] Please let us know if you have any additional questions.
From Section Page: Napoleon Wood Stoves [2]
ID: napoleon-wood-stoves
Links:
------
[1] http://ww...
Our Answer:
Unfortunately, no. The see-thru woodburning fireplaces that we sell
are not stainless steel and not suitable for use outdoors. We
apologize for this inconvenience.
From Section Page: FMI Fireplaces [1]
ID: fmi-fireplaces
Links:
----...
Our Answer:
This will depend on exactly how much clearance there is from the
fireplace opening to the window. Most manufactures will specify a
minimum distance to windows, as temperature extremes can cause
tempered glass to crack or shatter.
From ...
Our Answer:
Yes, our valves and covers can be installed in a wall next to the
fireplace.
From Section Page: Fireplace Keys and Valves [1]
ID: fireplace-keys-and-valves
Links:
------
[1] http://www.efireplacestore.com/fireplace-keys-and-valves.h...
Our Answer:
I am assuming that this measurement is the outer diameter? If so,
this is indeed 7 inch diameter B-vent piping and can use the Metal-Fab
Type B Round Chimney Pipe Storm Collar - For Chimney Pipes with a 7
Inch Inner Diameter [1] and the M...
Our Answer:
These items are known as firebrick, although the size of the brick in
your fireplace is not common and almost appears to be more of a tile.
They appear to be perfectly square.
From Section Page: Fireplaces [1]
ID: fireplaces
Links:
-...
Our Answer:
While most 18" ventless gas log sets will fit inside that 32"
Breckenridge, some 24" sets can fit as well. Please see our full
selection of ventless gas logs below, and let us know if you want us
to verify proper fitting for a particular ...
Our Answer:
While we do not carry a specific 4- to 6-inch pellet stove to
stovepipe increaser, we do have a piece that could serve this purpose.
Please see this item: PelletVent Chimney Adaptor [1] This adaptor will
work with 4" PelletVent Pro pipe a...
Our Answer:
Only some of the ornate, fan type screens are completely opaque. Most
others have a fine mesh that you can easily see the fire through.
From Section Page: Uniflame Fireplace Screens [1]
ID: uniflame-fireplace-screens
Links:
------
[1...
Our Answer:
This part is available, and your cost would be $18.95 plus shipping.
This item is currently in stock and would be shipped the same or next
business day upon order, but you would need to call us to order, as
the item is not on the website....
Our Answer:
When starting a wood fire in an outdoor firepit, dry pine or poplar
kindling is usually the best material to get a good fire burning. If
you must use a starting agent to get the fire burning, it is
acceptable to use lighter fluid, typical...
Our Answer:
Unfortunately, there is not a way to adapt this size flue collar to
the oval chimney. By code, it is possible to extend your round, single
wall stovepipe into the chimney and have it terminate at the first
clay flue tile. However, I recom...
Our Answer:
Usually, most of the manufacturing oil burn off and paint curing will
be completed by the first 10-12 hours of burn time. If the unit was
produced very recently, the cure time can be a bit longer. If the
smell persists, I would recommend ...
Our Answer:
The 120 volt motors for this unit are fairly universal and can
replaced with a similar model. Most local electronics shops could do
this kind of rebuild. You could also purchase a replacement motor,
based on the specifications on the buil...
Our Answer:
Here are just a couple. We have several more: Bellows 1 [1] Bellows 2
[2] Please let us know if you have any additional questions.
From Section Page: Bellows [3]
ID: bellows
Links:
------
[1] http://www.efireplacestore.com/cpf-68060....
Our Answer:
Generally, you are indeed able to install a pellet burning insert
into an existing fireplace, but the type of fireplace will be the
determining factor as to whether or not this can actually be
accomplished. Is the fireplace that you have ...
Our Answer:
In most cases, direct vent and some sealed B-vent fireplaces will
have metal clasps or screw clasps that will hold the glass in place.
Depending on your unit, the clasps may be on the top, bottom, or upper
and lower sides. Usually, top an...
Our Answer:
Without the model number of your fireplace, we cannot check for the
factory replacements, which may still be available. However, we do
offer some universal refractory panels that will work for your
woodburning fireplace. Please see the fo...
Our Answer:
Being that the fireplace is 36" high, you would need to have an
additional shroud fabricated to cover the distance from the medium
sized 32" high shroud.
From Section Page: Fireplace Insert Facings and Surrounds [1]
ID: fireplace-inse...
Our Answer:
My apologizes, but I do not see any past emails regarding this
fireplace. We do offer universal style hoods with a 6-inch projection
that can be surface mounted above the fireplace, but they are made to
order and cannot be returned. We al...
Our Answer:
Most co-linear venting systems will have a stamped label made into
both the appliance adapter and the termination cap that will identify
exhaust from intake. You can also inspect the inside of either liner.
While gas appliances do burn re...
Our Answer:
Manufactured propane fireplace inserts can indeed be installed into a
separately purchased wooden cabinet. The Napoleon Princess mantel is
designed to work with certain Napoleon fireplaces, however the cabinet
can be modified by a cabinet...
Our Answer:
A B-Vent fireplace can indeed run its Type B pipe up an existing
brick chimney. You can run the Type B pipe into a masonry wall, then
pass through it with a thimble and connect it to a flexible aluminum
liner.
From Section Page: B-Vent...
Our Answer:
We have the Monessen BDV300NSC7 currently on sale for $1,201.50
(regular price is $1,525.99). Please see the item page at the link
below: Monessen Direct Vent Gas Fireplace [1] Please let us know if
you have any additional questions.
Fr...
Our Answer:
Proper log sizing would depend upon your control preference and gas
type. Per your dimensions, you could safely install an 18" or 20" log
set with remote control in either natural gas or propane. Or, you
could opt for a match light 24" lo...
Our Answer:
We are a retailer of several brands of hearth products, however we do
not offer repair services at this time. It would be necessary to
contact a local Heat N Glo dealer in your area or a qualified hearth
technician for service. Heat N Glo...
Our Answer:
California has strict guidelines for installation of both gas and
wood burning fireplaces. Vent free appliances are not allowed by law
and wood burning fireplaces must be EPA Tier II certified, meaning
that they have an output of 7.5 gram...
Our Answer:
The facings that we carry are intended for use with certain brands
and models of fireplaces. I will be happy to check into the dimensions
of one of the surrounds we carry, as it may be able to be retrofitted
to your brand of insert. What ...
Our Answer:
The type of hood needed will depend on the fireplace you have. Is
this a manufactured fireplace or a site-built masonry unit? Do you
have doors across the front of the fireplace opening? What is the
width of the fireplace opening and the ...
Our Answer:
One fire pit burner, pan, and gas valve will be needed to complete
your project. We have numerous options that can be used. To narrow the
selection, you will need to know the exact width or dimensions of the
fire pit opening and if the pi...
Our Answer:
Issues with incomplete combustion are usually the result of irregular
log placement on the burner assembly, resulting in flame impingement
(contact) with the logs. If the logs are installed according to the
manufacturer's instructions, th...
Our Answer:
Choosing between vented and ventless is entirely up to you, as long
as ventless logs are permitted by your local building code. For a
brief summary of the differences, please see this explanation from our
website: Vented Gas Logs - Vented...
Our Answer:
We do offer a damper pull that has a cast handle, indicating whether
the damper is opened or closed. The item is the UniFlame Solid Brass
Fireplace Damper Pull [1].
From Section Page: Fireplace Accessories [2]
ID: fireplace-accessorie...
Our Answer:
Unfortunately, the logs and burner assembly of a direct vent insert
can not be swapped out with another burner assembly. A standard vented
gas log set would not be an appropriate fit for your appliance. Your
best bet would be to search fo...
Our Answer:
While we are a retailer of single walled stovepipe, we do not have
the facilities to custom fabricate seamless lengths of piping. This
would likely need to be done by a custom sheet metal fabricator, as I
am not aware of a product on the ...
Our Answer:
Yes, and we do offer R.H. Peterson's Real Fyre ventless glass burner
systems.
From Section Page: Gas Fire Glass Sets [1]
ID: gas-fire-glass-sets
Links:
------
[1] http://www.efireplacestore.com/gas-fire-glass-sets.html
Our Answer:
In most cases, a blower cannot be added to gas logs by themselves.
Where the logs installed into a masonry or manufactured fireplace? If
they are installed into a manufactured box, does it have louvers on
the face? What is the manufacture...
Our Answer:
A standard brass cleaner should work perfectly well for this
application.
From Section Page: Gas Fireplaces [1]
ID: gas-fireplaces
Links:
------
[1] http://www.efireplacestore.com/gas-fireplaces.html
Our Answer:
The biggest consideration you have is the feasibility of fitting a
full-bodied insert inside your existing fireplace versus the option of
simply installing a gas log set inside (burner and logs). First,
please confirm in your manual that ...
Our Answer:
Unfortunately, the blower model for your Majestic fireplace was
discontinued about five years ago and there is no replacement
available. We apologize for this inconvenience.
From Section Page: Fireplaces [1]
ID: fireplaces
Links:
--...
Our Answer:
The only model of Ecofan currently made that is three bladed is the
gas stove variant. All wood stove variants are now two bladed, as the
motors have been revised to offer increased CFM output, without the
use of a third blade.
From Sec...
Our Answer:
While not one and the same, ethanol units and gel fuel models are
very similar. There is no clear advantage or disadvantage to one over
the other. A key consideration for you would be the access and pricing
of local denatured alcohol (for...
Our Answer:
We offer a variety of natural gas vented and ventless log sets that
feature the option to add a hand-held remote control. If you are
replacing a log set that was installed inside a brick/masonry
fireplace or a manufactured woodburning fir...
Our Answer:
No. All direct vent fireplaces can only be used to burn natural gas
or propane.
From Section Page: Direct Vent Fireplaces [1]
ID: direct-vent-fireplaces
Links:
------
[1] http://www.efireplacestore.com/direct-vent-fireplaces.html
Our Answer:
For best heating results, we recommend a ventless gas log set [1].
You would close the damper on your Heatilator and all the heat stays
in the room. If you reply with the dimensions of your fireplace (front
width, rear width, depth) as we...
Our Answer:
There are several differences between direct vent and B-vent. For a
detailed explanation, please see our Gas Fireplace and Stove Buying
Guide [1].
From Section Page: Direct Vent Fireplaces [2]
ID: direct-vent-fireplaces
Links:
------...
Our Answer:
The manufacturer for our chimney top dampers explicitly warns against
using them with gas logs. This is because a failure to open could
cause carbon monoxide to back up into the house. Moreover, in the case
of a gas leak, gas could be tra...
Our Answer:
Unfortunately, vent-free fireplaces cannot be field-converted for
fuel type. As such, there will be no conversion kit available for your
model. We apologize for this inconvenience.
From Section Page: Fireplace Adaptors & Conversion Kits...
Our Answer:
We offer both vent types. Please use the check boxes on the left of
the page (under "Vent Type") to select the vent type you prefer.
From Section Page: Natural Gas Fireplace Logs [1]
ID: natural-gas-logs
Links:
------
[1] http://www....
Our Answer:
While it depends on the fireplace, most refractory panels used in
manufactured fireplaces are largely decorative. There is usually a
metal chassis behind the panels that seals the entire firebox. Cracks
up to 1/8 inch in diameter are acce...
Our Answer:
The Osburn 2400 High-Efficiency EPA Woodburning Stove [1] is our
largest model. It features a 100,000 BTU maximum output, when using
seasoned cord wood.
From Section Page: Wood Burning Stoves [2]
ID: wood-burning-stoves
Links:
-----...
Our Answer:
Vent-free and ventless gas appliances are made for either natural gas
or propane. These are not interchangeable, and since the units cannot
be field-converted, care must be taken to ensure the proper fuel type
is selected.
From Section...
Our Answer:
The closest standard key size that would be close is a 5/16" key.
However, it is possible that the gas valve uses a manufacturer
specific key that is not a common size and it could be metric. With
the wall escutcheon removed, use a tape m...
Our Answer:
While we do offer 48" x 48" and 36" x 52" boards, we do not carry
anything that is larger than these dimensions. This is largely due to
the shipping limitations of boards that are any larger than this. Most
larger hearth pads must be site...
Our Answer:
We do indeed have a few different remote controls that you can use
with your Empire Innsbrook insert: Remote Control 1 [1] Remote Control
2 [2] Remote Control 3 [3]
From Section Page: Remote Controls [4]
ID: remote-controls
Links:
--...
Our Answer:
The Majestic BC42 Royalton Woodburning Fireplace [1] uses the SK8
double-wall chimney pipe (8" inner diameter and 11" outer diameter),
which we carry. All of the compatible chimney parts can be found in
the "Venting Components" tab on eac...
Our Answer:
It would indeed be possible to install a ventless fireglass burner in
place of the more traditional ceramic log set. Before we could make
any recommendations, we would need to knwo if you are interested in
manually controlling the burner ...
Our Answer:
Only a handful of wood burning fireplaces are designed to have
comparable efficiency to an insert. The units are closed combustion
models that use a small firebox and limited combustion air to create
an intense fire, much like the inserts...
Our Answer:
No, there is no blower available for these Hearth Sense models. We
apologize for this inconvenience.
From Section Page: Hearth Sense Fireplace Inserts [1]
ID: hearth-sense-fireplace-inserts
Links:
------
[1] http://www.efireplacesto...
Our Answer:
Vent-free fireplaces cannot be converted.
From Section Page: Fireplace Keys and Valves [1]
ID: fireplace-keys-and-valves
Links:
------
[1] http://www.efireplacestore.com/fireplace-keys-and-valves.html
Our Answer:
If the technician quoted you this amount just for replacement
refractory panels for the interior of your metal fireplace, that price
seems excessive. We offer some universal refractory panels that will
work for your wood-burning fireplace...
Our Answer:
Assuming that the current valve is located within a standard sheet
rock wall, this would be a medium difficulty project. If the gas
piping runs in a fairly straight line towards the fireplace, a plumber
could remove the current valve and ...
Our Answer:
We do offer three different sizes of a Smoke Rollout Eliminator,
which may solve your problem. The goal of the smoke guard would be to
reduce your fireplace opening so that you can achieve a 10 to 1 ratio
between your fireplace opening an...
Our Answer:
We are not a Mendota dealer, so we do not have any mantels that are
made for their models. We apologize for the inconvenience.
From Section Page: Wood Fireplace Mantels [1]
ID: wood-fireplace-mantels
Links:
------
[1] http://www.efi...
Our Answer:
After checking with FMI, I was informed that the refractory hearth
panel is no longer available through them. He did inform me that the
correct blower assembly is indeed still available. The part number for
the appropriate blower is VCBK3...
Our Answer:
The Flame Monaco XTD EPA Zero Clearance Wood Burning Fireplace [1]
would be my first recommendation in your search for a high efficient
wood burning fireplace that is also reasonably priced. This unit,
however cannot be ducted directly in...
Our Answer:
No. Ventless (or vent-free) gas logs are only meant to be installed
in existing wood-burning fireplaces (brick/masonry or manufactured
fireplaces that are listed to accept gas logs) or universal, vent-free
fireboxes.
From Section Page:...
Our Answer:
Unfortunately, we do not offer a high heat paint that is designed to
paint a cook top. High temperature enamel that is specifically
designed for close contact to food must be used. This appliance enamel
can usually be purchased at special...
Our Answer:
Because this particular gas log set does not have a listed
temperature limit, I would recommend painting the box with a high
temperature paint that is rated to 1,200 degrees. This is standard for
all vented and vent free gas logs, while w...
Our Answer:
While we do not offer ceramic or terra cotta flue tiles, we do carry
manufactured chimney, which can be used to vent an outdoor fireplace.
An anchor plate would be used to affix the chimney to the top of the
smoke shelf, then chimney sect...
Our Answer:
Unfortunately, none of the inserts we sell are designed to fit in
fireplaces that wide or that short. You would likely need to get an
insert that will fit in the middle of your fireplace and then have
something custom-made to cover the re...
Our Answer:
Direct vent fireplace venting systems remain open to the outdoors at
all times. This is also the case with B-vent fireplaces. Most units
have a built in draft diverter that is designed to eliminate cold back
drafts into the unit.
From S...
Our Answer:
It is indeed possible to use the Stove Bright paint (note: not the
"Gas Vent Pipe" colors, these have a lower temperature rating) in your
application. While it would not withstand the heat of a woodburning
fire, it should fare better in y...
Our Answer:
I'm sorry, but we do not have this information on file. Please
contact your local building inspector for more information regarding
local codes.
From Section Page: Pellet Vent Pipe [1]
ID: pellet-vent-pipe
Links:
------
[1] http://w...
Our Answer:
Yes, please measure the inside diameter of your pipe. Being able to
identify the manufacturer/model information of the pipe will also be
helpful, if you want a factory replacement.
From Section Page: Chimney Caps [1]
ID: chimney-caps
...
Our Answer:
Unfortunately, we do not carry a cleaner that would effectively
remove this type of residue. However, I can recommend using a 1" razor
blade. Remember to use a new blade and to slowly work the blade back
and forth beneath the residue, tak...
Our Answer:
What you describe is similar to the revolving lighted drum that is
used to back light electric fireplaces and give the illusion of a
fire. However, I do not carry a system that can be retrofitted to an
existing fireplace. All products tha...
Our Answer:
If you plan on using a fireback without support boots, it is best to
use one that is as wide as the back wall of your prefab box and about
1-2 inches shorter than the back wall. Use of the support boots will
raise the fireback by 2 to 2.5...
Our Answer:
Because the Breckenridge VFD36FB2DL is a vent free model, glass doors
cannot be used with this fireplace. However, a number of decorative
screen doors are available and can be seen under the items
accessories.
From Section Page: Firepla...
Our Answer:
Unfortunately, we do not have the manufacturer-specific panel that
you are looking for, but we do offer some universal refractory panels
that will work for your woodburning fireplace. Please see the
following links: One 24\"h x 28\"w Pane...
Our Answer:
Unfortunately, we do not offer a universal replacement panel that
features the raised ash lip that your unit has now. Even though Marco
is no longer manufacturing fireplaces, you may try contacting a dealer
for Lennox Hearth Products, as ...
Our Answer:
We do indeed carry numerous replacement remotes compatible with FMI
products. In order to make sure I suggest the correct replacement
remote, I will need to know the model number that is listed on the
back of your current remote. Also, ju...
Our Answer:
All of the high-heat paint we offer is only available in a spray-on
application. We apologize any inconvenience.
From Section Page: Stove Paint & Fireplace Paint [1]
ID: paint
Links:
------
[1] http://www.efireplacestore.com/paint.ht...
Our Answer:
We do indeed sell both bowl and flat style fire pit pans.
From Section Page: Patio Tables with Fire Pits [1]
ID: patio-tables-with-fire-pits
Links:
------
[1] http://www.efireplacestore.com/patio-tables-with-fire-pits.html
Our Answer:
All of our R.H. Peterson (Real Fyre) logs are manufactured from
refractory cement and can be used outdoors without a problem. However,
if you are interested in purchasing a burner assembly as well, it will
be necessary to make a selection...
Our Answer:
If you are simply relining the chimney for continued use as an open
faced model, you would need to use a bottom support plate and support
leg system. An example of the bottom plate is the HomeSaver Pro 18
inch x 18 inch Top/Bottom Plate f...
Our Answer:
No, vent-free logs cannot be installed inside a direct vent
fireplace. Direct vent models must use the log set/burner assembly
that comes included, as the sealed combustion chamber is tested and
engineered only for that set-up.
From Se...
Our Answer:
We do indeed have color charts that could be mailed to you.
From Section Page: Stove Bright Paint [1]
ID: stove-bright-paint
Links:
------
[1] http://www.efireplacestore.com/stove-bright-paint.html
Our Answer:
Unfortunately, we only sell the Ambient RCT [1] remote complete with
both the transmitter and receiver. We apologize for the inconvenience.
From Section Page: Remote Controls [2]
ID: remote-controls
Links:
------
[1] http://www.efir...
Our Answer:
Yes, the Majestic WMC42 WarmMajic Circulating Wood Burning Fireplace
does require a hearth brick refractory panel, which is included with
the fireplace. You should get a factory replacement if it is missing.
We can get a replacement heart...
Our Answer:
We understand your concern about a gas-burning appliance that has no
exhaust. Vent-free fireplaces and stoves are designed to burn cleanly,
so there is no incomplete combustion, and, thus, no carbon monoxide.
The clean combustion by-produ...
Our Answer:
Certainly. As long as the triple wall chimney is in good condition,
it can house a liner to size down the flue for an insert or stove.
From Section Page: Chimney Liners [1]
ID: chimney-liners
Links:
------
[1] http://www.efireplacest...
Our Answer:
Sizing of the chimney pipe will depend on the appliance. Most modern,
high efficiency appliances will require a 6 inch chimney pipe,
although some large models will require 7 or 8 inch. The design of
each appliance will only allow a certa...
Our Answer:
A solid glass panel is only required on direct vent gas fireplaces.
B-vent gas fireplaces usually have optional glass door kits, whereas
vent-free gas fireplaces cannot have glass doors, since those units
need to be open to use room air f...
Our Answer:
Yes, all of our Peterson RealFyre vented gas log sets have the option
to add an on/off remote pilot kit or a variable flame remote pilot
kit. Either of these pilot kits allow for the use of a thermostatic
hand-held remote control, where y...
Our Answer:
Manufactured (metal) vent free fireplaces do indeed lack a chimney or
external vent of any sort. They will recirculate and heat room air,
using a precision burner system that avoids releasing harmful amounts
of carbon monoxide into the ro...
Our Answer:
You may find a gas flex line to connect the gas line to your burner
assembly. We have many different lengths of flexible gas line to
connect the pipe to your burner.
From Section Page: Vented Gas Logs [1]
ID: vented-gas-logs
Links:
-...
Our Answer:
Unfortunately, the fireplace inserts that we offer do not have an
option for an ash pan or tray. Ashes must be raked or swept to the
front of the unit and removed using a handheld ash pan. This is one
disadvantage to an insert over a free...
Our Answer:
Our Real Fyre ventless gas logs are 99.9% efficient, as the heat has
nowhere to go but in the room where you are burning the log set.
In Response to Question:
Where can I find the efficiency rating percentage for gas logs? I
have the...
Our Answer:
If your model is tested and listed to accept gas logs, we do have
several see-thru gas log sets [1] that may interest you.
From Section Page: Gas Logs [2]
ID: gas-logs
Links:
------
[1] http://www.efireplacestore.com/see-thru-gas-lo...
Our Answer:
Only fireplaces that are specifically designed for outdoor use can be
used outside. Standard fireplaces simply cannot withstand the elements
and increased humidity in an outdoor application.
From Section Page: FMI Fireplaces [1]
ID: f...
Our Answer:
We have a limited selection of see-through vent-free appliances, and
fewer still that can be framed into a wall. If you are searching for a
zero-clearance, two-sided, vent free fireplace, please check out our
Vail 36\" [1].
From Sectio...
Our Answer:
When referencing liner panels, the front width of the fireplace
opening is used as a sizing gauge.
From Section Page: Fireplace Panels and Liners [1]
ID: fireplace-panels-and-liners
Links:
------
[1] http://www.efireplacestore.com/fi...
Our Answer:
We recommend a see-thru gas log set, which are available in both
vented and ventless configurations. Please see our full selection
below: See-Thru Gas Logs [1] If you prefer, you can reply with your
fireplace dimensions and preferences (v...
Our Answer:
Any of our R.H. Peterson See Thru Gas Logs [1] could be used for this
type of installation. Narrowing your search by the required fuel type,
size, and pilot type will give you a more accurate group to choose
from. Selecting vented or vent...
Our Answer:
Many of the Osburn stoves and inserts come with a set of metal build
plates that are packed in the firebox area when the unit is shipped
out. These plates will contain the model and serial number of the
unit. If you no longer have these b...
Our Answer:
The largest vent-free set we carry is 30 inches in width. The reason
for the size limitation is linked to the BTU output limitation of
40000 BTUs for a vent-free log set. Any larger burner would yield a
flame that is too low to be appeali...
Our Answer:
The gas valve assembly on a gas fireplace has a slotted adjustment
screw which can be used to lessen the pilot output. However, please be
careful when adjusting this. It must be done in small increments, as
the flame still needs to engulf...
Our Answer:
Unfortunately, we do not have any paint that is rated for direct
contact with flames. As such, none of our paint will be fireproof. We
apologize for the inconvenience.
From Section Page: Stove Paint & Fireplace Paint [1]
ID: paint
Li...
Our Answer:
For standing pilot lights, the basic difference is how the system
will be controlled. The first option is manual control. For this
option, the system is started by turning a knob on the pilot. The
second option is remote control. In this ...
Our Answer:
Unfortunately, this is a rather uncommon size. All of our keys fit
1/4" to 5/16" valve stems. A specialty plumbing shop may have a key
for your application.
From Section Page: Fireplace Keys and Valves [1]
ID: fireplace-keys-and-valv...
Our Answer:
Indeed, if you are using an electric insert, you can use some Stove
Bright paint such as this for inside your firebox: Stove Bright Flat
Black Paint - 43205 [1] There are other colors available. Please see
all of our paint here: Stove Bri...
Our Answer:
We do not offer any installation services. For your reference, you
may use the NFI (National Fireplace Institute) website to locate a
local certified installer in your area. Once there, just click on the
"Public" link on the right hand si...
Our Answer:
Yes, we have a variety of fire pit burners you can use for your
installation. Please see our full selection below: Fire Pit Burners
[1]
From Section Page: Fire Pits [2]
ID: fire-pits
Links:
------
[1] http://www.efireplacestore.com/f...
Our Answer:
Typically, sealant is not used on single wall stovepipe joints.
Properly crimped stovepipe will not leak, nor does the newer welded
pipe, which fits together very tightly. It is prudent to use sheet
metal screws at each joint, as this wil...
Our Answer:
Unfortunately, none of our glass enclosures can be made large enough
to cover your opening. We recommend searching for a fireplace glass
door manufacturer that can customize a door assembly for you.
From Section Page: Stoll Fireplace D...
Our Answer:
If you need a vented see-thru propane gas log set, please see the
Real Fyre See Thru 24\" Post Oak Vented Propane Gas Logs Set with
Safety Pilot Kit [1]. If you want a ventless see-thru propane gas log
set, please see the Real Fyre See Th...
Our Answer:
When making any gas connections, I highly recommend have a licensed
plumber do the work. They will be equipped with the tools to properly
seal and leak test their connections.
From Section Page: Vent Free Fireplace Inserts [1]
ID: ven...
Our Answer:
In most cases, it is best to repaint the entire affected panel in
order for the best match to be achieved. A wide range of different
finishes and variations in color can make a localized touch up of the
paint nearly impossible. I recommen...
Our Answer:
The NPL-PTH31GTSSP can indeed be converted to natural gas, as
Napoleon does make a conversion kit available for this purpose. On our
site, on the item page, you would select "Natural Gas" in the "Choose
Fuel Type" drop-down menu under the...
Our Answer:
If you are looking to heat this entire area with a vent-free
fireplace, we recommend a unit with a BTU rating of 35,000-40,000
(which is the maximum for a vent-free appliance). Please see a couple
of suggestions below: Monessen DFS Vent-F...
Our Answer:
The components you describe are known as refractory liner panels.
These components can be replaced with the original manufacturer
panels, if they are still available. Otherwise, universal panels must
be cut to fit. Majestic would usually ...
Our Answer:
This particular unit is no longer manufactured. However, the current
FK12 fan kit [1] is still available and is the recommended unit for
this fireplace. The kit can also be equipped with a variable speed fan
control [2] to offer greater u...
Our Answer:
Any hearth rug that is manufactured from olefin will be your best
choice. Olefin is a naturally flame- and heat-resistant fiber that
does an excellent job of repelling hot embers and shielding
combustible floors from radiant heat.
In Re...
Our Answer:
We do sell replacement log lighters, which will include the fittings
needed to attach to your incoming gas line.
From Section Page: Fireplace Accessories [1]
ID: fireplace-accessories
Links:
------
[1] http://www.efireplacestore.com...
Our Answer:
Many local chimney sweeps or HVAC technicians will perform this type
of installation. It is also possible to search for National Fireplace
Institute-certified experts via their website. NFI techs that carry
the NFI wood-burning certificat...
Our Answer:
Yes, you have the Empire Tahoe Deluxe Direct Vent Natural Gas
Fireplace [1]. You can see the owner's manual for this unit here:
owner's manual [2]
From Section Page: Direct Vent Fireplaces [3]
ID: direct-vent-fireplaces
Links:
------...
Our Answer:
The most common cause of this issue with vent free fireplaces is a
dirty pilot assembly. Lint and dust can build up on the pilot and
cause the assembly to malfunction. I recommend using compressed air to
blow the pilot assembly clean and ...
Our Answer:
While we do have some wall-mounted vent-free fireplaces, the only
ones that do not require electricity are our ethanol or gel fuel
models. Please see some examples below: Napoleon Vent-Free Square
Ethanol Fireplace [1] Napoleon Vent-Free ...
Our Answer:
We may have one for your unit, depending on the manufacturer and
model number. Please reply with this information and we will check
availability.
From Section Page: Fireplace Insert Facings and Surrounds [1]
ID: fireplace-insert-faci...
Our Answer:
While it depends on the particular log set that you have, it is
typical for the log set to have a pair of main bottom logs. The logs
are positioned at the front of each side of the log grate. Various
other logs are usually provided to lay...
Our Answer:
If solid fuel is being burned, Class A chimney must also be used.
Pellet pipe is simply not rated for use with solid fuel appliances.
We'd be happy to put a quote together for you for this pipe. We would
just need the details of the insta...
Our Answer:
If your fireplace has a sealed glass front, it cannot be a vent-free
unit. Vent-free fireplaces cannot have glass fronts or doors, as they
need to "breathe" to bring in combustion air and release carbon
dioxide and water vapor. Regardless...
Our Answer:
According to the information I was able to locate for this stove,
this model uses a standard millivolt gas valve, which is quite common.
As such, any millivolt remote system could be used for your
application. If you would like simple on/...
Our Answer:
Unfortunately, all of the fire pit burners we currently offer must be
vented. We do offer some vent free burner assemblies, but they are
designed to be used in a standard firebox and would not offer the
desired appearance for a fire pit.
...
Our Answer:
Unfortunately, the FMI pipe that the Bungalow uses and the Heatilator
pipe that you currently have will not be compatible with one another.
It would be necessary to replace the existing chimney system with the
proper FMI 8DM line of pipin...
Our Answer:
For your application, we recommend contacting a local machine shop or
sheet metal fabricator to have an oval-to-round adaptor custom-made.
From Section Page: Type B Vent Pipe [1]
ID: type-b-vent-pipe
Links:
------
[1] http://www.efi...
Our Answer:
The only birch logs we sell are vented, not ventless. We apologize
for this inconvenience.
From Section Page: Gas Logs [1]
ID: gas-logs
Links:
------
[1] http://www.efireplacestore.com/gas-logs.html
Our Answer:
Unfortunately, we do not have a material that is designed to patch
ceramic liner panels. In the event of a ceramic liner cracking, it is
best to replace the panel.
From Section Page: Fireplace Insert Panels and Liners [1]
ID: fireplac...
Our Answer:
By "battery wall unit", are you referring to the remote receiver? The
remote receiver takes four AA batteries and supplies a voltage signal
to your appliance. This component is a necessary piece in the remote
system as it controls your ap...
Our Answer:
The 810 and 810a are both versions of the basic Ecofan, which have an
output of 105 CFM and a temperature range of 150 to 650 degrees
Fahrenheit. The 810am is the "Air Max" version, which has the same
operating range and an output of 130C...
Our Answer:
My apologies, but the largest diameter table that we currently offer
is 48 inches. I am sorry that we do not offer a larger table.
From Section Page: Patio Tables with Fire Pits [1]
ID: patio-tables-with-fire-pits
Links:
------
[1] h...
Our Answer:
Please reply with the model number of your Vermont Castings unit, and
we will be happy to check availability on a replacement rear panel for
you. We look forward to your response.
From Section Page: Fireplaces [1]
ID: fireplaces
Link...
Our Answer:
Yes, our outdoor gas fireplaces also provide a generous amount of
heat, though not as much as a wood-burning fireplace.
From Section Page: Patio Fireplaces [1]
ID: patio-fireplaces
Links:
------
[1] http://www.efireplacestore.com/pa...
Our Answer:
We have a variety of complete firepit kits that may interest you.
Please see some suggestions below: Napoleon Patioflame Stainless Steel
Outdoor Firepit [1] Napoleon Linear Patioflame Gas Fire Pit [2]
Peterson Outdoor Campfyre 34 Inch Til...
Our Answer:
The closest we have would be something like this Goods of the Woods
Sage Green Half Round Guardian Hearth Rug - 32 Inch x 60 Inch [1].
From Section Page: Hearth Rugs [2]
ID: hearth-rugs
Links:
------
[1] http://www.efireplacestore.c...
Our Answer:
The logs themselves will have a limited lifetime warranty. If the
logs break or crack under normal conditions for any reason, the
manufacturer will replace them free of charge. The burner assembly is
warranted for a period of 10 years, wh...
Our Answer:
The manufacturer has confirmed that the newer 8UT chimney system has
replaced the 8T system that you have now. The parts are virtually the
same and are readily interchangeable. The exact part that is
equivalent to the 8T-36 you are lookin...
Our Answer:
My apologizes, but we do not carry a premanufactured firebox of this
size. Because of the very large dimensions, this type of unit would
likely need to be custom made and listed by a fabricator.
From Section Page: Fireplace Fireboxes [1...
Our Answer:
Unfortunately, we do not stock a product that meets those
specifications. Our closest selection is a pint sized can of 1200
degree [1] paint.
From Section Page: Stove Paint & Fireplace Paint [2]
ID: paint
Links:
------
[1] http://ww...
Our Answer:
Each of these options are excellent for your application. Napoleon,
Majestic and Monessen are all top-of-the-line manufacturers. The best
unit to maximize your available space may be the Napoleon LHD50, which
you can see here: Napoleon LH...
Our Answer:
Our only stove that offers a cook-top surface is the Napoleon 1150P
EPA Wood Gourmet Cook Stove [1].
From Section Page: Wood Stoves [2]
ID: wood-stoves
Links:
------
[1] http://www.efireplacestore.com/npl-1150p.html
[2] http://www.e...
Our Answer:
While we do not carry any corner gas inserts, we do have some corner
model zero clearance manufactured gas fireplaces. Please see the "Gas
Fireplace" section of our page here: Gas Fireplaces [1] Once there,
please use the search bar on th...
Our Answer:
A popular unit that can be used for this purpose is the Napoleon
Patioflame Stainless Steel Outdoor Firepit [1]. The unit requires only
72 inches of clearance to a ceiling and can be surrounded with
decorative noncombustible material of y...
Our Answer:
The type of key will depend on the gas valve that you have. Does the
gas valve have a round, decorative cover with a small hole in the
center? If so, this type of valve likely requires a 1/4 inch key. The
decorative cover can be unscrewed...
Our Answer:
Unfortunately, no, we do not offer any see-through (two-sided)
fireplace inserts at this time. We only have these models available in
a zero-clearance fireplace.
From Section Page: Wood Burning Fireplace Inserts [1]
ID: wood-burning-...
Our Answer:
Based on the diameter of your pit, a 30 inch fire ring would be the
most suitable size. I do recommend using a pan to support the
surrounding media that you may use, such as glass, logs, or lava rock.
We do offer pans that measure 36 to 3...
Our Answer:
Most likely, the blue flame is being caused by a fuel mixture that is
too "rich" or fuel heavy. There should be an air shutter or air valve
that can be opened to balance the incoming air to the burner assembly.
This is usually located on ...
Our Answer:
The correct door and blower assembly for your needs will depend
entirely on the manufacturer and model number of the unit. The unit
should have a build plate, either within the firebox itself or beneath
the fireplace floor. The plate will...
Our Answer:
You would need to order the replacement logs listed in the
replacement parts section of your owner's manual.
From Section Page: Fireplace Embers & Rocks [1]
ID: fireplace-embers---rocks
Links:
------
[1] http://www.efireplacestore.co...
Our Answer:
Our olefin rugs are naturally resistant to sparks and hot embers.
This material will have by far the greatest resistance to damage,
should a hot ember fall out upon the rug.
From Section Page: Hearth Rugs [1]
ID: hearth-rugs
Links:
-...
Our Answer:
DuraVent does not make a pitched roof flashing for the DuraChimney II
pipe, only a flat chase top flashing. Per the manufacturer, you will
need to have one field-fabricated.
From Section Page: Chimney Products [1]
ID: chimney-product...
Our Answer:
Yes, we have one 48" x 48" stove board that has an R-value of 3: R-CO
48-in. x 48-in. Double Cut Brick Stove Board [1] Our other 48" x 48"
boards have varying R-values, though none are greater than 2.
From Section Page: Hearth Boards &...
Our Answer:
You may be interested in using a Napoleon fireplace in conjunction
with a hand carved wooden mantel, such as the Thomasville [1]. This
mantel can be installed and made to look like it was built on site,
rather than most cabinets which hav...
Our Answer:
Unfortunately, the only style of screen that we offer that surpasses
the standard 33 inch height is a rumford style screen, such as the
Pilgrim Traditional Rumford Fireplace Spark Guard with Vintage Iron
Trim and Twisted Bar Handles [1]. ...
Our Answer:
This unit is available in several different versions, including an
island (4-sided), peninsula, left and right corner, and thru. Natural
vent, also known as B-vent, is a type of fireplace that vents its
exhaust to the outdoors but draws c...
Our Answer:
Yes, if the fireplace has been tested and listed for gas logs. A
glass door is not required to have a vented gas log set. If the
fireplace has functional chimney pipe installed that runs over the
roof, you can get a vented gas log set [1]...
Our Answer:
A true dual-fuel fireplace is not available. The appliance would have
to be dedicated to either wood or propane. However, there is an option
to add a gas log light to many of our wood-burning fireplaces.
From Section Page: Gas Fireplac...
Our Answer:
Generally, the best way to stop this from happening is to use a
chimney cap that is oversized to the chimney opening.
From Section Page: Chimney Caps [1]
ID: chimney-caps
Links:
------
[1] http://www.efireplacestore.com/chimney-caps....
Our Answer:
Select items on our Web site can indeed be shipped to you in Canada.
However, we cannot offer free shipping on orders shipped outside of
the 48 continental United States. In some cases, our website will not
allow you to check out if you a...
Our Answer:
Our vent free gas logs can use down to a 20 pound propane cylinder,
but this will limit the amount of time the unit will be able to burn
before requiring time to vaporize more fuel. The larger the cylinder
that can be used, the better.
...
Our Answer:
We have a few options to help you in your quest for a linear
top-vented fireplace. Please see a few of our available units below:
Top-vented Fireplace 1 [1] Top-vented Fireplace 2 [2] Top-vented
Fireplace 3 [3] Top-vented Fireplace 4 [4] ...
Our Answer:
Per your description, it sounds as if the gas pressure being supplied
to the unit is out of range. Does the unit have a regulated gas valve?
If not, has a gas regulator been installed prior to the valve to step
down gas pressure?
From ...
Our Answer:
Because the door rails are usually not sold separately from the
glass, you will have only the options of painting the door rail or
replacing the entire door assembly. Brass can be painted with high
temperature paint, but time must be take...
Our Answer:
It seems as if the gas valve itself may have an internal fault that
is causing this issue, especially when considering that the remote
servo was never able to open the valve by itself. I will be happy to
file a warranty claim for a replac...
Our Answer:
Please see some of our suggestions below: Fireplace Insert 1 [1].
Fireplace Insert 2 [2]. Fireplace Insert 3 [3]. Fireplace Insert 4
[4]. We have several others, as well: Fireplace Inserts [5]. Each
insert's item page should list the requ...
Our Answer:
I would still suggest the use of stainless components due to the
humidity and temperature changes that the burner and log set would be
subjected to.
From Section Page: Ventless Gas Logs [1]
ID: ventless-gas-logs
Links:
------
[1] htt...
Our Answer:
While we do offer vent free fireplace inserts that are designed to be
placed within an existing fireplace, we do not carry individual panels
that can perform the same task.
From Section Page: Fireplace Panels and Liners [1]
ID: firep...
Our Answer:
Yes, likely you will need to run the venting vertically over your
roof. Please check with the manufacturer for specific venting
installation information.
From Section Page: Gas Fireplaces [1]
ID: gas-fireplaces
Links:
------
[1] htt...
Our Answer:
Yes we do have fireplace inserts with your requests. Please go to the
link to view an example of one our units that might work for you. We
can help you with a specific fireplace if we have your measurements
and gas type. Napoleon GI3600 N...
Our Answer:
While we do not carry such an item, our distributor, P&D Metal Works,
may be able to custom fabricate one for you. They can be reached at
1-920-727-1947.
From Section Page: Fire Rings for Fire Pits [1]
ID: fire-rings-for-fire-pits
Li...
Our Answer:
Unfortunately, the chimney surrounds that we offer only come in faux
brick. I am not aware of a faux stone chimney surround that is
currently offered by any manufacturer. It is likely that you will need
to face one of the brick surrounds ...
Our Answer:
First, you would need to ensure that the pellet stove in question has
been tested and listed for use in mobile home applications. Moreover,
it is likely you will need to replace the entire chimney pipe system
and replace it with type L pe...
Our Answer:
Indeed, you may use Rutland stove paint in a masonry application. The
surface should be as clean and dry as possible. Also, remember that
multiple light coats are better than few thick coats.
From Section Page: Stove Paint & Fireplace P...
Our Answer:
The only other option for your woodburning fireplace that we can
offer are our universal refractory panels. These are gray with a
stacked brick pattern. Please see the following links: One 24\"h x
28\"w Panel [1] Two 24\" h x 40\"w Panels...
Our Answer:
My apologies, but the narrowest outside width that we have for any of
our mantles is 60 inches. We did have a couple of models that were
narrower, but they have since been discontinued. Again, I am sorry
that we do not have an item for yo...
Our Answer:
Unfortunately, no, you cannot use real wood on a gas log burner.
However, you may absolutely install a natural gas log lighter into
your wood burning fireplace. As their name suggests, our log lighters
make lighting a wood fire much simpl...
Our Answer:
The Rutland Pre-Mixed Black Furnace Cement - 10.3 Ounce Cartridge [1]
will be the best product to seal the crack. This adhesive can
withstand the high temperatures generated by the stove and is very
workable.
From Section Page: Wood Sto...
Our Answer:
Any of the stainless steel units that we offer would be best suited
to be left out in the elements. Stainless Steel Toolset 1 [1]
Stainless Steel Toolset 2 [2] Stainless Steel Toolset 3 [3] I hope you
find this information useful to you. ...
Our Answer:
Unfortunately, the longest firebrick that we have to offer measures 9
inches in length. We do not have a supplier that we work with that
makes a longer or thicker brick. Firebrick can often be procured from
specialty building material sup...
Our Answer:
We are an independent online retailer and sell several brands of gas
fireplace inserts. As such, I will require the manufacturer's name and
model number of the fireplace in order to provide the proper lighting
instructions. Most units wil...
Our Answer:
While we do sell some decorative gas logs, they are intended for use
only with R.H. Peterson Real Fyre vented gas log burners. Please see
them below: Real Fyre 9\" Oak Branches - Two in Box [1] Real Fyre
Bonus Designer Logs - Set of 2 [2]...
Our Answer:
The best product we offer for this purpose is the Rutland Castable
Refractory Fireplace Cement - 12.5 Pound Tub [1]. This item is
designed to be cast into irregular shapes and can patch odd sized
holes and cracks. The product is hydraulic...
Our Answer:
One of our most popular outdoor vent free units is the Alpine Outdoor
36 in. Natural Gas Vent Free Fireplace System [1]. This system offers
a great deal of supplemental heat and will require no electrical
supply. The stainless steel chass...
Our Answer:
The mantle shelves will include the wall cleat and basic hardware to
mount them. However, masonry anchors will need to be purchased if the
shelf is being mounted to a brick or stone facing.
From Section Page: Mantel Shelves [1]
ID: ma...
Our Answer:
Is your intent to completely remove the existing fireplace? If so,
then yes. It would be absolutely possible to frame in a new fireplace
in place of the old unit and run the necessary vent pipe for this new
appliance. If you're planning f...
Our Answer:
This will depend entirely on the size and condition of the existing
fireplace and its associated chimney. There are many specialty log
systems and gas coal baskets that are intended for smaller fireplaces
that previously burned wood or co...
Our Answer:
We apologize, but none of our paint is made to withstand direct
contact with flames. We recommend searching for a specialized
high-heat paint that can be used for this type of application. We are
sorry that we cannot assist you with this....
Our Answer:
Yes, please see our UniFlame 5-Piece Stainless Steel Indoor/Outdoor
Fireplace Tool Set [1].
From Section Page: Fireplace Tool Sets [2]
ID: fireplace-tool-sets
Links:
------
[1] http://www.efireplacestore.com/uf-f-7710.html
[2] http:/...
Our Answer:
The best replacement screen for your needs is the Cascade Black
Fireplace Mesh Panel Replacement Kit - 24 Inch x 19.5 Inch [1]. This
panel set includes a pair of 24 inch panels, which will cover your
opening completely and offer a fair am...
Our Answer:
The type of pipe you will need will depend on the model of the
fireplace. You can also fill out our Chimney Pipe Design and Quote
Form [1].
From Section Page: Stove Pipe [2]
ID: stove-pipe
Links:
------
[1] http://www.efireplacestore...
Our Answer:
In order to insulate this unit, prior to installing the insert, I
would recommend using the following liner panels: Liner Panel 1 [1]
Liner Panel 2 [2] These panels will need to be cut to fit; however,
you should be able to use the factor...
Our Answer:
Depending on your unit, there are a few places the manufacturer
information may be located. The first location would be a metal plate
that is on the left or right side of the smoke shelf bracket, right at
the top of the fireplace front op...
Our Answer:
This would indeed be a suitable item, however the cast iron insert
would indeed need to be positioned into an existing masonry fireplace
or pushed into an acceptable manufactured fireplace with a properly
functioning chimney. These types ...
Our Answer:
Because fireplace inserts do not have a conventional ash pan, they
must be cleaned by using an ash rake or shovel to pull ashes to the
door opening. The ashes can then be scooped into an ash bucket or
removed with an approved ash vacuum. ...
Our Answer:
We carry this Hearth Products Controls 3/4 Inch Manual Ball Valve
[1].
From Section Page: Fireplace Keys and Valves [2]
ID: fireplace-keys-and-valves
Links:
------
[1] http://www.efireplacestore.com/hpc-226-hc.html
[2] http://www.efi...
Our Answer:
The floor plate/escutcheon is a purely decorative piece that can be
unthreaded and then rethreaded without an issue. It has no direct
contact with the seal in the gas valve, so a gas leak will not be an
issue.
From Section Page: Firepl...
Our Answer:
I will be happy to check into the availability of a factory hood for
your fireplace. If one is not available, a universal model may be able
to work in its place. Please provide the model number of the Vanguard
fireplace at your convenienc...
Our Answer:
Unfortunately, no. A blower is only helpful in circulating warmth
from the fireplace into the room and can actually cause the drafting
issue to become worse in some cases. Smoke back drafting is usually
related to either a disproportionat...
Our Answer:
While we do not sell any universal glowing ember kits for vent-free
log sets, if you reply with the manufacturer and model of your unit,
we may be able to obtain a factory replacement for you.
From Section Page: Fireplace Embers & Rock...
Our Answer:
The openings you describe are indeed common on many models of
circulating fireplace. This would allow a fan or pair of fans to be
used to circulate air. Unfortunately, we only offer blowers for
specific units. We do not sell them by dimen...
Our Answer:
No, this conversion it not possible. We recommend any of our ventless
propane log sets. Please see our full selection below: Ventless Gas
Logs [1] Please note the fuel type, as vent-free appliances cannot be
field-converted.
From Secti...
Our Answer:
Yes, we offer many electric inserts and mantel packages. Please see
our full selection of electric fireplaces [1], many of which are part
of a mantel/cabinet/entertainment center package.
From Section Page: Fireplace Mantels [2]
ID: ...
Our Answer:
Unfortunately, no. All of the propane-fueled heaters we carry will
have a fixed, umbrella style burner.
From Section Page: Patio Heaters [1]
ID: patio-heaters
Links:
------
[1] http://www.efireplacestore.com/patio-heaters.html
Our Answer:
Unfortunately, we do not offer a truly universal product that can be
used to fit this unit. Upon searching, it would also appear that the
manufacturer did not offer such an accessory for this unit. A few of
our customers have had custom s...
Our Answer:
Unfortunately, we would not be able to provide a direct fit panel
without first knowing the manufacturer name and model number of the
fireplace. With this information, we can check availability of the
original panel. Otherwise, a universa...
Our Answer:
This issue is often the result of a dirty or partially clogged pilot
assembly. In order to clean the pilot, the nut that is threaded to the
end of the pilot tube will need to be loosened and disconnected from
the pilot assembly. The nut i...
Our Answer:
No, the Napoleon GDI-30G model [1] is a "fireplace insert," which
means it must be installed inside an existing fireplace (either a
vented masonry/brick fireplace or a vented, fabricated woodburning
fireplace). For a zero clearance model,...
Our Answer:
Unfortunately, all of Peterson's vent-free burners are very log
specific. You have to use the Peterson vent-free log set with the
correct Peterson vent-free burner or risk allowing the gasses not to
completely combust, filling your home w...
Our Answer:
This type of installation would require just a few components. Please
see the below list of items. I did not include a flashing as one is
not often used at the top of a masonry chimney. Instead a flat chase
top flashing is normally custom...
Our Answer:
For your installation, I believe you would be best suited by the
Cascade Black Fireplace Mesh Panel Replacement Kit - 24 Inch x 27.5
Inch [1] and the Woodfield Hanging Fireplace Spark Screen Rod Kit -
61090 [2]. The screen kit offers a pa...
Our Answer:
A hood can deflect heat around the television, as long as the
television does not project more than 2 inches further than the hood
itself. For example, a 6-inch hood could protect a TV that projects up
to 8-inches from the wall.
From Se...
Our Answer:
Thank you for this information. We recommend the Medium Innsbrook
Vent-Free Gas Fireplace Insert with Millivolt Controls [1], which
comes standard with the burner, log set, decorative brick panels,
blower and remote-ready millivolt pilot ...
Our Answer:
Yes, the DuraPlus galvalume and stainless pipe sections are
interchangeable, as long as the inner diameters are the same.
From Section Page: Class A Chimney Pipe [1]
ID: class-a-chimney-pipe
Links:
------
[1] http://www.efireplacest...
Our Answer:
Your options will depend on the type of setup that you have
installed. Is this a masonry or manufactured fireplace that had vented
gas logs installed into it or did the unit come as a package with the
logs and burner as part of the assemb...
Our Answer:
Direct vent fireplace inserts utilize outside air for combustion, as
well as venting their exhaust gases to the outdoors. This is
accomplished by the use of a pair of 3 or 4 inch diameter aluminum
liners. These will be routed up the chimn...
Our Answer:
Unfortunately, neither of the requested accessories are available for
the 36CDVZRRN line of fireplaces. Majestic simply does not produce
them for them.
From Section Page: Fireplace Panels and Liners [1]
ID: fireplace-panels-and-liner...
Our Answer:
It appears you would need a kit like this: Venting kit [1] This is
also available in 25-, 30- and 35-foot lengths. This product has a 3"
inner diameter.
From Section Page: Napoleon Fireplaces [2]
ID: napoleon-fireplaces
Links:
------...
Our Answer:
We offer the CrownSeal Pre-Mixed Flexible Waterproof Coating - 2
Gallon Tub [1] as a great option for waterproofing chimney crowns,
chimney corbels, and other masonry surfaces.
From Section Page: Chimney Caps [2]
ID: chimney-caps
Lin...
Our Answer:
This type of setup would indeed need to be vented. There are a
limited number of vent free burners available for glass beads, but
they do not allow the burner itself to come in contact with the
decorative media. Rather, the media would be...
Our Answer:
G4 burners are primarily used in combination with a grate and log
assembly. PB burners are truly pan burners and are used as glass
burners without a grate and log set.
From Section Page: Gas Log Burners Only [1]
ID: gas-log-burners-on...
Our Answer:
From your description, it sounds like relining the chimney with a
stainless steel chimney liner will be the best option to pursue. We
would need more information before we could direct you to a product,
including the dimensions of the flu...
Our Answer:
If you are looking for a refractory panel for your fireplace, please
see this 28" wide by 24" tall universal panel that can be cut to size:
Hargrove Replacement Fireplace Refractory Panel - 24 inch X 28 inch
[1] This panel is 3/4" thick. ...
Our Answer:
Unfortunately, we do not carry an oval adapter that will match these
size requirements. As oval adapters become more difficult to find, it
is often necessary to have a custom adapter fabricated by a local
sheet metal shop.
From Section ...
Our Answer:
If you reply with your fireplace's front (opening) width, the rear
width, the depth (front to back) and the the opening height, we can
advised on properly-sized inserts. In some cases, you will be able to
vent through an existing chimney,...
Our Answer:
All current models of Majestic fireplace will be listed by any one of
several testing agencies. Active agencies include UL, Omni, and PFS.
From Section Page: Chimney Products [1]
ID: chimney-products
Links:
------
[1] http://www.efir...
Our Answer:
Rotate the gas control knob from the "off" to the "pilot" position.
Push the red spark ignitor button repeatedly while pushing the gas
knob in. The pilot should light. Continue holding the knob for 30
seconds. The thermocouple should now ...
Our Answer:
We recommend a stainless steel tool set for outdoors. Please see a
suitable set here: UniFlame 5-Piece Stainless Steel Indoor/Outdoor
Fireplace Tool Set [1]
From Section Page: Outdoor Fireplace Accessories [2]
ID: outdoor-fireplace-ac...
Our Answer:
We do not sell such a blower, as our wood-burning grate/blower
systems (such as this Stoll 24 in. W x 20 in. D Grate Heater [1]) are
not suitable for use outdoors.
From Section Page: Fireplace Blowers and Fans [2]
ID: fireplace-blowe...
Our Answer:
Are you referring to something like lava rock? If so, yes, we do
indeed offer this item. Please follow the below link to check out one
of our options. Peterson Lava Coals [1] Please let us know if you have
any additional questions.
From...
Our Answer:
Please view the cap at the link below. It has an outside perimeter
band as you describe and can adjust between 16.5" to 18.5" on one side
and 20.5" to 22.5" on the other. This should suit your needs
accordingly. Chimney Cover [1] Please l...
Our Answer:
With a 43 inch opening, you would be able to use most wood burning
inserts that we carry. However, you will also need to know the height
and depth of the opening to be certain. Finally, what is the amount of
square footage that you would ...
Our Answer:
No, your tiles can indeed stay in place; and yes, if the tiles are
not cracked or damaged, you can use pour-down insulation to surround
the liner. We recommend the HomeSaver Insulation Mix [1].
From Section Page: Chimney Liners [2]
I...
Our Answer:
We have several options for your application. Do you want a
traditional log set in the fireplace, or would you prefer a
contemporary glass or stone kit? Approximately what size (width) do
you need? We have linear see-through fireplaces up...
Our Answer:
For painting the inside of a gas fireplace, we recommend this item:
Stove Paint [1].
From Section Page: Stove Paint & Fireplace Paint [2]
ID: paint
Links:
------
[1]
http://elitedeals1.helpserve.com/www.efireplacestore.com/cpf-43400....
Our Answer:
We do indeed carry vent free burners, however they cannot be
purchased without the log set. This is due to safety issues that can
arise if incompatible logs and burners are used together.
From Section Page: Gas Log Burners Only [1]
I...
Our Answer:
Yes. Because of the size of your fireplace opening, the side panels
would need to be tilted at a broad angle, however the screen would
stand and cover the opening completely.
From Section Page: Fireplace Screens [1]
ID: fireplace-scre...
Our Answer:
Just to clarify, would this be something that is used in a brick
fireplace or a manufactured (metal) fireplace? I am also a little
unclear about the part you are referring to. We have gas burners that
usually are covered with a thin layer...
Our Answer:
We do indeed offer 24" and 30" propane ventless log sets with
hand-held thermostatic remote control options. Please see some of them
below: Log Set 1 [1]. Log Set 2 [2]. Log Set 3 [3]. Log Set 4 [4].
There are several other options as wel...
Our Answer:
There are several differences between direct vent and vent-free
fireplaces, stoves and inserts. For more information, please see both
our Gas Fireplace and Stove Buying Guide [1] and our Fireplace Insert
Buying Guide [2].
From Section ...
Our Answer:
Our smallest space heaters are vent-free units, whereas our vented
heaters are console-style and considerably larger. Here is an example
of one of the vent-free models we have: Vent-Free Space Heater [1].
Our full selection of heaters can...
Our Answer:
Unfortunately, all of our glass enclosures are surface-mounted over
the face of a fireplace. We do not offer any magnetically-attached
door assemblies.
From Section Page: Fireplace Insert Doors and Screens [1]
ID: fireplace-insert-do...
Our Answer:
This will depend on the model of your current fireplace.
From Section Page: Fireplace Insert Blowers and Fans [1]
ID: fireplace-insert-blowers-and-fans
Links:
------
[1]
http://www.efireplacestore.com/fireplace-insert-blowers-and-fa...
Our Answer:
The RH Peterson glass is intended to be used with a pan burner. As
such, we sell the complete Gas Fire Glass Sets [1].
From Section Page: Fireplace Glass and Architectural Shapes [2]
ID: fireplace-glass-and-architectural-shapes
Link...
Our Answer:
Unfortunately, we do not have any universal accessories for ventless
or vent-free gas log sets. This is due to the meticulous nature of the
vent-free burner systems; the only decorative accessories that can be
added to your set must be sp...
Our Answer:
It is recommended that you thoroughly clean the surround before
painting. Please see below for a recommendation for flat and satin
black paint options: Stove Bright Flat Black Paint - 43205 [1] Stove
Bright Satin Black Touch Up Paint - 43...
Our Answer:
The entire line of Real Fyre vented logs that we carry can be readily
converted from one fuel to another. Conversion only requires the
changing of an orifice and the main burner air shutter. However,
conversion of any CSA/ANSI certified b...
Our Answer:
"HT" listed chimney is simply Class A chimney pipe listed for use for
"high temperature" exhaust, hence the "HT." We recommend using the
DuraVent DuraTech double-wall Class A chimney pipe. You can see all of
our Class A chimney pipe here:...
Our Answer:
Unfortunately, the largest square pre-manufactured stove boards that
we carry measure 48" x 48". This is because shipment of anything
larger than this would have to be done by a specialty freight carrier.
Most floor protection that is lar...
Our Answer:
Hairline cracks are normal and should not cause concern. However,
cracks larger than 1/8" necessitate a replacement refractory panel or
brick. If you have a small crack, you may use fireplace mortar [1] or
the Defy Masonry Crack and Joint...
Our Answer:
You would need a full stainless steel firebox for use in a screened
porch, as the moisture in the outside air will eventually rust and
corrode a standard metal firebox. Please see our full selection of
stainless steel outdoor options, inc...
Our Answer:
If your fireplace is complete and the chimney is in good working
order, either system can be used. Vented logs offer a high flame and
BTU output, giving the most realistic appearance. The logs are also
placed more naturally, further enhan...
Our Answer:
That model number is incomplete, but it looks like you are
referencing the Vantage Hearth VB42L1I [1]. That unit uses the BDB42
series of doors, of which there are three available finishes. Please
see them below: Black finish [2] Brushed ...
Our Answer:
Our surface mount hoods would require that you drill into the marble.
We also have hoods that attach to the fireplace lintel and hoods that
attach to a glass enclosure (doors.)
From Section Page: Fireplace Hoods [1]
ID: fireplace-hoo...
Our Answer:
There are four different options for remotes with our Peterson Real
Fyre Ventless Gas Logs. First, there are two options for the On/Off
Automatic Pilot Kit log sets. The first is a basic on/off remote that
simply turns the log set on or o...
Our Answer:
My apologies, but we do not carry a fireplace insert that could fit
into a 20 inch wide opening. Our smallest model would require at least
24 inches to fit properly. Because of the tall, narrow size of your
fireplace, it will likely be di...
Our Answer:
The water vapor released into the room from the burning of propane is
indeed one of the big arguments against using vent-free appliances, as
it may cause windows to fog up and there have been issues with mildew
in some cases. For more det...
Our Answer:
If feasible, it is preferable to go with a top vent model, which you
can then run the vent pipe up a short distance (1-2 feet), then elbow
out 90-degrees and terminate on an exterior wall.
From Section Page: Direct Vent Fireplaces [1]
...
Our Answer:
The Breckenridge Deluxe 36" fireboxes are best suited for our 24"
Real Fyre ventless gas log sets. However, you will need to
double-check the required dimensions to ensure proper fitting before
ordering.
From Section Page: Ventless Gas...
Our Answer:
Yes, the burner you are using must be tested and listed for use with
fire glass. You cannot use fire glass on any vented gas burner.
From Section Page: Fireplace Glass and Architectural Shapes [1]
ID: fireplace-glass-and-architectura...
Our Answer:
If you are site building a fireplace, but would like to use Class A
pipe to vent it, you will need to use an anchor plate to transition
from the firebox to the chimney. An example is the DuraTech All-Fuel
Chimney Pipe Masonry and Zero-Cle...
Our Answer:
It is usually possible to accentuate a propane burner with lava rocks
or granules. Glowing ember material can also be used. However, only a
limited amount of material can be used in some fireplaces and
placement of any accessory embers wi...
Our Answer:
For your reference, you may use the NFI (National Fireplace
Institute) website to locate a local certified installer in your area.
Their website is www.nficertified.org. Once there, just click on the
"Public" link on the right hand side a...
Our Answer:
Some of our more popular models of "clean face" direct vent units are
the Napoleon BGD36CFNTR [1] as well as the Monessen Belmont [2]. Both
of these models feature the clean face design and sizing you are
described. We also offer cost eff...
Our Answer:
Ideally, you would utilize a 3 panel screen that has at least 1 inch
of height beyond the opening of the fireplace. A screen with either a
28 or 30 inch center panel would work. These screens will have 11 and
12 inch side panels, respecti...
Our Answer:
A similar and very popular model is the FMI Bungalow - Builder 36
Inch Radiant Wood Burning Fireplace - Smooth Face [1]. Do you have any
manufacturer or model information from the current fireplace? If so,
we may be able to set you up wit...
Our Answer:
Match light gas log sets will not have a pilot assembly. Rather, you
would need to use a lighter or long match to manually light the log
burner after opening the gas valve. In order to extinguish the flames,
you would simply close the gas...
Our Answer:
The Stove Bright paint can be used to paint the outside of fireplace
doors.
From Section Page: Stove Paint & Fireplace Paint [1]
ID: paint
Links:
------
[1] http://www.efireplacestore.com/paint.html
Our Answer:
Unfortunately, we do not offer any fixed glass panels that can be
used to replace existing bifold doors. An item like this would need to
be custom made, with air intakes so the fire can still pull in
combustion air from the room. I apolog...
Our Answer:
Are the widths on each of your fireplaces the same in the front as in
the back? This is almost always the case for a see-through fireplace,
and you can install a 30" see-thru gas log set if your see-through
unit has 42" of width all the w...
Our Answer:
Yes, we do have a couple of indoor/outdoor see-thru direct vent gas
fireplace options for you to consider. Our largest is the Majestic
48\" Marquis Clean Face See-Thru Direct Vent Gas Fireplace (Natural
Gas) [1]. You must also get the Maj...
Our Answer:
We have two electric inserts with a depth of 7.75" that may work for
your application. Please see them below: Classic Flame Traditional
Elegance Built-In Electric Fireplace Insert [1] Classic Flame
Contemporary Built-In Electric Fireplace...
Our Answer:
Porcelain does not refer to the type of gas, but rather the type of
material the fireplace or burner assembly is finished in. Most gas
units come set up to operate on either natural gas or propane.
From Section Page: Fireplaces [1]
I...
Our Answer:
In order for a fireplace or log set to use fire glass or fire shapes,
it must be able to use an adapter kit or tray that will allow you to
spread the glass or position the shapes accordingly. Without the tray,
flame impingement will resul...
Our Answer:
While these Heatmaster vent-free fireboxes are not available in
stainless steel, we do have a couple of other options for you. Please
see the following: Vantage Hearth Sagamore Vent-Free Outdoor Firebox
with Ivory Herringbone Brick Refrac...
Our Answer:
While it is not recommended to paint firebrick panels, you may
certainly use a stone/cement cleaner to restore them. An item such as
this [1] will do the job of removing built-up soot stains and burn
residue.
From Section Page: Fireplac...
Our Answer:
Propane has a higher energy content than natural gas, but is usually
more expensive to use. If natural gas is available in your area, it is
generally the preferred fuel, as the cost is less, not storage tank is
required, and vaporization ...
Our Answer:
Unfortunately, not. Class A chimney is only permitted to offset by 30
degree elbows. If you'd like to reply with the brand of chimney pipe
you are using, we'd be happy to match up an elbow kit for you.
From Section Page: Chimney Pipes ...
Our Answer:
While we do stock many styles of outdoor logs and outdoor fireplaces,
none of the items are equipped with blowers. It would be cost
prohibitive for manufacturers to equip their products with a blower
that is fully weather sealed, as stand...
Our Answer:
"Square end" refers to the shape of the hood itself, which you can
see in the picture/diagram above
From Section Page: Fireplace Hoods [1]
ID: fireplace-hoods
Links:
------
[1] http://www.efireplacestore.com/fireplace-hoods.html
Our Answer:
Because of the dangers of incorrectly converting a vent free
fireplace, manufacturers do not produce conversion kit components for
them. It is possible to release harmful carbon monoxide into the room
if the main burner orifice is not ins...
Our Answer:
The only wood burning stove that we currently offer with the ability
to convert to a rear-vent unit is this: Wood Burning Stove [1] The
side clearances of this stove are 16", however, and the rear clearance
is 22". Please let us know if y...
Our Answer:
We apologize, but we only offer the full Ambient remotes with the
hand-held transmitter and receiver as a package. You may want to try
contacting the manufacturer directly for more information; you can
reach them at http://ambienttechnolo...
Our Answer:
Top sellers for this square footage range are the Napoleon Large
Pedestal Wood Burning Stove [1], the Osburn 2400 High Efficiency EPA
Woodburning Stove [2] and the US Stove Extra-Large EPA-Certified
Wood-Burning Stove [3]. All three stove...
Our Answer:
Generally, either a basket type grate or the Pilgrim series of
diamond steel grates will have the highest front. It is usually
standard to have 3 to 4 inches of space on either side of the grate.
In order to determine what grate you need,...
Our Answer:
The difficulty with locating this product is mostly due to the fact
that 7" diameter stovepipe has become very uncommon. Due to the lack
of demand for this size of stovepipe and the increasing scarcity of
barometric dampers in general, ou...
Our Answer:
All of our mesh screens are the standard pull variety with a
chain-link appearance. We do not have any that are marketed as
allowing more heat into the room.
From Section Page: Mesh Fireplace Screens [1]
ID: fireplace-mesh
Links:
--...
Our Answer:
We do indeed have this unit available and it can be seen on its item
page [1]. Shipping to your location would be free of charge. You would
only pay the advertised sale price listed on the item page.
From Section Page: Wood Burning Fire...
Our Answer:
If you have a manufactured woodburning fireplace, you can use this
panel: One 24\"h x 28\"w Panel [1] This panel is 3/4" thick and can be
cut down to the size you need with a masonry blade or tile saw.
From Section Page: Fireplace Pane...
Our Answer:
A log set by R.H Peterson will make a difference as the logs
themselves are constructed from refractory cement. As the fire is
burning the logs will absorb heat to help radiate the heat into the
living space while the fire is burning, as ...
Our Answer:
Free standing wood stoves can be placed into a noncombustible alcove,
but it is best to leave them in an open space to allow best thermal
efficiency. How much square footage would the unit ideally heat?
Addition of a convection blower wou...
Our Answer:
No. As is the case with all Class A chimney pipe, you must use the
same model, size and manufacturer for each chimney component; these
brands are not interchangeable. You must use the same manufacturer's
pipe for your entire chimney syste...
Our Answer:
Heat-N-Glo is a line manufactured by Travis Industries, who we are
not a dealer for. Currently, they will only sell to local dealers. As
such, you will likely need to check with local Heat-N-Glo dealers to
see if they still have this pane...
Our Answer:
Unfortunately, we do not sell the brown paint in the gallon size.
From Section Page: Stove Paint & Fireplace Paint [1]
ID: paint
Links:
------
[1] http://www.efireplacestore.com/paint.html
Our Answer:
We do carry the Sunjel fuel in 24 canister packages [1].
From Section Page: Sunjel Fireplaces [2]
ID: sunjel-fireplaces
Links:
------
[1] http://www.efireplacestore.com/sun-24canpack.html
[2] http://www.efireplacestore.com/sunjel-fi...
Our Answer:
Based on the depth of your fireplace, it definitely seems like this
must be a Victorian styled firebox. Unfortunately, I do not have a log
set that could accommodate the 9 inch depth. The only vent free units
I offer in the reduced depth ...
Our Answer:
It is not recommended to paint over brick and mortar, as the high
temperatures often cause the paint to discolor and separate quickly.
The better option would be to apply a thin coating of refractory
mortar over the existing material. Thi...
Our Answer:
We do not have a cap that is exactly the size you need. The closest
we offer is this Gelco Model D 17 in. x 41 in. Base Stainless Steel
Multi-Flue Chimney Cap [1].
From Section Page: Chimney Caps [2]
ID: chimney-caps
Links:
------
[1...
Our Answer:
We may be able to get the factory replacements for your Majestic
unit. If they are no longer available, please see these universal
panel options: El Dorado Decorative Brick Firebox Panel [1] Seville
Decorative Brick Firebox Panel [2] Flor...
Our Answer:
Based on reviews from our customers, the AW Perkins Brick and Stone
Cleaner [1] is an excellent product for removing soot stains from real
masonry and refractory cement liners alike.
From Section Page: Fireplace Maintenance [2]
ID: f...
Our Answer:
While we do offer a large variety of chimney rods, they are available
only in 1/4, 3/8, 3/4, and 7/8 inch sizes. The 5/8 inch rods are
definitely not a common size and I currently do not have adapters
available for them. Just to be certai...
Our Answer:
Assuming you are talking about the Napoleon Linear Patioflame Gas
Fire Pit (found here [1]), we do indeed have the river rock kits
available in gray or a multicolored kit. You can find them on that
page linked above within the "Accessorie...
Our Answer:
Before I can check into this, please provide us with the item
number(s) of the product(s) that you are interested in. We will wait
for your response. In the meantime, if you are inquiring about a
fireplace insert, please note that most of...
Our Answer:
This will depend on the type of bi-fold doors. The bi-fold doors that
are specified for use with manufactured fireplaces are not airtight
and will usually have an 1/8 inch gap between the panels. However,
masonry bi-fold doors, such as th...
Our Answer:
A direct vent fireplace can be installed on an inside wall and
horizontally vented, however you will need to ensure that you have
space in the adjacent area for a venting system to be enclosed in a
chase wall. In regards to the vent free ...
Our Answer:
Unfortunately, we do not offer a lot of vent free appliance quite
that wide. Our largest has an overall width of 52". It is manufactured
by Vantage Hearth: Vantage Hearth Luminary [1].
From Section Page: Wood Stoves [2]
ID: wood-stove...
Our Answer:
While we do not have a direct vent linear unit that is exactly 36"
wide, we do have models that are close. Please see a few below: Medium
Loft Direct Vent Gas Fireplace with Remote-Ready Millivolt Controls
[1] (The glass viewing area on t...
Our Answer:
Unfortunately, we do not have anything available for your particular
model. To see if an alternate door kit is available, please contact
the manufacturer or a local dealer for more information.
From Section Page: Fireplace Specific Fir...
Our Answer:
Yes, ventless gas logs can indeed be installed in a masonry/brick
fireplace or a manufactured wood-burning fireplace that has been
tested and listed to accept gas logs. No venting would be required. In
either case, the damper for the exis...
Our Answer:
None of our full-bodied fireplace inserts will fit in that opening,
but a gas log set such as this Real Fyre 18\" Charred Oak Vented
Natural Gas Logs Set - Match Light [1] will fit. This gas log set can
only be used with a fireplace that ...
Our Answer:
Unfortunately, the largest screen we carry is 50" x 49".
From Section Page: Fireplace Screens [1]
ID: fireplace-screens
Links:
------
[1] http://www.efireplacestore.com/fireplace-screens.html
Our Answer:
Ember glow should be spread in a thin layer at the front of the
burner pan and under the front logs, just short of contacting the main
burner flame. It is important not to pile up the material over the
ember burner, as this can cause exce...
Our Answer:
The hood you have sounds like a model that is specific to the
fireplace itself. Most of the hoods we carry are universal models that
must be screwed into place. In order to find the correct part number
for the type of hood you have, you w...
Our Answer:
The Pilgrim Six-Bar Narrow Steel Fireplace Grate [1] would be the
ideal sized grate for your fireplace.
From Section Page: Fireplace Grates [2]
ID: grates
Links:
------
[1] http://www.efireplacestore.com/fsd-18609.html
[2] http://www...
Our Answer:
No, there are no vent free wood burning stoves.
From Section Page: Vent Free Stoves [1]
ID: vent-free-wood-stoves
Links:
------
[1] http://www.efireplacestore.com/vent-free-wood-stoves.html
Our Answer:
As long as the kit is correctly matched to your unit and the kit is
installed properly, the unit will operate as if it came from the
factory with the kit installed. Due to the difference in BTU potential
between natural gas and propane, t...
Our Answer:
Unfortunately, all of our vent-free heaters are wall mounted or
free-standing units. Most of our vent-free fireplaces [1] can indeed
be recessed, however.
From Section Page: Vent Free Fireplaces [2]
ID: vent-free-fireplaces
Links:
-...
Our Answer:
There is no clear answer on this; it depends on the fireplace model
(BTU output) and how your television is installed (recessed, wall
mount, etc.). The majority of heat from a vent-free fireplace comes
out right at the top of the opening,...
Our Answer:
We do carry several deck mats that are designed to protect the area
beneath a raised fire pit. An example is the Goods of the Woods 36
Inch Round Protective Deck Mat - Brown [1]. Our other offerings can be
seen by typing the phrase "deck ...
Our Answer:
Any of our high temperature paint would work just fine for your
application. Is there a specific color in which you are interested?
We'd be happy to search for a color for you. Please let us know if you
have any additional questions.
Fr...
Our Answer:
We are not a Heatilator dealer, so we are unable to confirm whether
or not the Osburn 1100 is safe for use with your model. As for the
size requirements, the Osburn 1100 requires the following fireplace
size: Height: 22" Opening Width: 26...
Our Answer:
We currently offer two products that may work for your application.
Please see both the Stoll 20 in. W x 17 in. D Grate Heater [1] as well
as the Stoll 24 in. W x 20 in. D Grate Heater [2].
From Section Page: Gas Logs [3]
ID: gas-logs...
Our Answer:
The closest replacement we carry would be the 24 Inch x 21.5 inch
replacement screen [1]. The hanging height will include the 1/2 inch
screen rings.
From Section Page: Mesh Fireplace Screens [2]
ID: fireplace-mesh
Links:
------
[1] ...
Our Answer:
We do have a couple of linear direct vent units that can be power
vented. Please see them below: Direct Vent Fireplace 1 [1] Direct Vent
Fireplace 2 [2] Here is the power vent terminal for these units, and
the appropriate adaptors: Power ...
Our Answer:
We would be happy to send you a quote for these items. Please reply
with a shipping address and we will send you a quote as quickly as
possible. Also, please advise on any optional accessories you may be
interested in, such as a blower, b...
Our Answer:
It is best to burn seasoned hardwoods, such as hickory, birch, and
oak. These types of woods have a higher BTU content and make for
longer burning, hot fires. For starting the fire, it is actually best
to build a small fire using crumpled...
Our Answer:
We actually have 3 available. We have a 20 in. W x 17 in. D Grate
Heater [1], a 22 in. W x 20 in. D Grate Heater [2] and a 24 in. W x 22
in. D Grate Heater [3].
From Section Page: Fireplace Grates [4]
ID: grates
Links:
------
[1] htt...
Our Answer:
There are varying degrees of rules and regulations against vent-free
appliances across the country, but we are not aware of any in New York
state. We recommend calling your local building inspector for more
information.
From Section Pa...
Our Answer:
Unfortunately, we do not have a reducer that can span this much
difference in diameters. Anything that is more than 2 inches will most
likely need to be custom fabricated, as it is not recommended to
reduce or increase most stovepipe more...
Our Answer:
The SC36 is an open-faced, inefficient woodburning fireplace with no
listed BTU rating from the manufacturer. As such, we cannot offer a
heating area approximation; we can tell you that any open-faced
wood-burner is primarily intended for...
Our Answer:
Per the manufacturer, these fire pits have a base diameter of 32
inches.
From Section Page: SoJoe Fire Pits [1]
ID: sojoe-fire-pits
Links:
------
[1] http://www.efireplacestore.com/sojoe-fire-pits.html
Our Answer:
We do offer individual flue extenders, such as the Gelco Stainless
Steel 8 in. x 13 in. Base 1 Foot Flue Stretcher [1]. These caps are
available in various sizes, so it is possible we may have one to suit
your needs.
From Section Page:...
Our Answer:
Conventional refractory brick liners are manufactured from a
combination of refractory cement, sodium silicate, and other
reinforcing materials. There is no finishing paint or other materials
added to most of these liners and they dry to ...
Our Answer:
Depending on your unit, there are a few places the manufacturer
information may be located. The first location would be a metal plate
that is on the left or right side of the smoke shelf bracket, right at
the top of the fireplace front op...
Our Answer:
The thimbles we have are meant to house Class A chimney pipe as it
passes through an exterior wall into a tee. For example, please see
the 6\" DuraTech All-Fuel Chimney Pipe Wall Thimble [1]. Please note
that for a wood-burning stove, the...
Our Answer:
Our freestanding wood stoves do not need an existing fireplace or
chimney. You will need to use 6" inner diameter stovepipe and 6" inner
diameter Class A chimney pipe to vent all of our models. If needed,
please fill out our Chimney Pipe ...
Our Answer:
It appears you need a fireplace insert--a unit that would slide
inside your existing fireplace and utilize an existing chimney. If
this is the case, please advise if you would prefer a woodburning
insert or a gas (direct vent or vent-free...
Our Answer:
Per the manufacturer: "Whenever somebody is in a salt air
environment, we recommend 304 grade stainless steel. They can purchase
the copper, but would recommend they purchase some sort of spray-on
finish like a clear rust protection finis...
Our Answer:
There are various aroma stones [1] available that are activated by
the heat of your fireplace. Unfortunately, we have none that features
the scent of naturally burning wood.
From Section Page: Ventless Gas Logs [2]
ID: ventless-gas-l...
Our Answer:
The type of burner needed will depend directly on the model of logs
that you currently have. Most 18" vented Real Fyre logs can work with
the G45 burner system, however vent-free logs require the same type of
vent-free burner system that ...
Our Answer:
If your woodburning fireplace is a brick/masonry unit, then you can
indeed install a direct vent insert like the Napoleon GDI-30G [1]. Any
direct vent insert will require co-linear liners (usually 3" in
diameter) to be run up your existin...
Our Answer:
Generally, when an item is listed as a "firebox," it will not include
a gas burner or a log set, whereas a "fireplace" will include the
firebox, the burner and the log set. Every unit on our website should
clarify what is included, but if...
Our Answer:
A millivolt system has a small flame that generates power for the
unit's gas valve to operate. As a result, they do not require outside
power to operate and can be used in the event of a power outage. The
only thing that would be rendered...
Our Answer:
Unfortunately, we do not carry any screens of this type. Everything
that we have will be a pull screen or free-standing variety.
From Section Page: Fireplace Screens [1]
ID: fireplace-screens
Links:
------
[1] http://www.efireplacest...
Our Answer:
Your model is a vent-free fireplace manufactured by DESA.
Unfortunately, vent-free units cannot be field converted to the other
fuel type. We apologize for this inconvenience.
From Section Page: Fireplace Accessories [1]
ID: fireplac...
Our Answer:
Please see these recommendations for painting the interior of your
fireplace: Firebox Paint 1 [1] Firebox Paint 2 [2] Please note these
paints will not last more than a season or two before the heat of the
flames will cause it to peel and...
Our Answer:
When it comes to doors for this unit, you have a couple of options to
explore. The original doors have been discontinued, but this set can
be used in their place: the Monessen Standard Bi-Fold Glass Fireplace
Doors with Black Track - For ...
Our Answer:
Given your description and the primer recommendation you have
received, I am assuming that you are referring to the exterior masonry
chimney, rather than the interior of the firebox. The Zinser 123
primer is a water based product that is ...
Our Answer:
Thermocouples are different from unit to unit. While some
thermocouples in home improvement stores are marketed as "universal",
they will not work for all appliances. Millivoltage for a thermocouple
can range from 50 to 250, depending on ...
Our Answer:
Do you notice the smell only when the log set is burning, or do you
get the smell when the damper is open and the log set is not burning?
Was the fireplace used for wood prior to installing the log set? If
so, was the chimney swept prior ...
Our Answer:
My apologizes, but we do not carry such an item. You will likely need
to inquire with a plumbing shop that sells specialty gas fittings.
From Section Page: Gas Connection Accessories [1]
ID: gas-connection-accessories
Links:
------
[...
Our Answer:
Yes, please see our full selection in the Gas Logs Only [1] section
on this website. Please note that these are Real Fyre brand gas logs
only intended for use with Real Fyre burners. Using them on another
burner will void the warranty.
...
Our Answer:
To re-line your chimney, you can use a bottom plate leg support
system in your chamber. You can see that item here: HomeSaver
Universal Size Bottom Plate Leg Support System [1] You would then
utilize an appropriately-sized bottom collar, ...
Our Answer:
Being that a wood burning fire generates a much greater amount of
heat than a gas fireplace, I would not recommend using a gas fireplace
to burn wood. The firebox and flue pipe itself is not rated to handle
the heat produced by a wood fir...
Our Answer:
The Osburn 2300 Wood burning Stove measures 31" tall with legs and 31
5/8" with the pedestal base. The outer width of the unit is 24 1/2"
with legs and 24 1/4" with the pedestal base. You can see it here:
Osburn 2300 Wood burning Stove [1...
Our Answer:
While we do not carry a wood burning fireplace that has a propane
lighter as standard, almost all wood burning models that we carry will
allow for the installation of a gas line and log lighter.
From Section Page: Fireplaces [1]
ID: ...
Our Answer:
While most of our freestanding fireplace screens are over 30" in
height, please see two options that are a bit smaller below: Pilgrim
Small 3 Panel Matte Black Arched Fireplace Screen [1] Pilgrim Matte
Black Traditional Fireplace Spark Gu...
Our Answer:
Any of our Stove Bright or A.W. Perkins wood stove paints can be used
to refinish this unit. I recommend sanding and cleaning the unit as
best you can prior to applying the new coat of paint. After sanding,
use a damp cloth to wipe the un...
Our Answer:
Unless the manufacturer offers glass doors as an option, there will
be no other way to make the fire viewable. Do you happen to know the
manufacturer name and model number of the insert? Please let me know
and I will be happy to check int...
Our Answer:
Because direct vent gas inserts have a built in blower system, a 110V
electric source will indeed be needed. The insert can technically be
used without the blower, but thermal efficiency of the unit will be
greatly diminished without it.
...
Our Answer:
While we do not offer a stove board with a precut hole for outside
air, an opening could be cut into any of the steel bodied boards that
we offer.
From Section Page: Stove Boards [1]
ID: stove-boards
Links:
------
[1] http://www.efi...
Our Answer:
While the purpose of gel fuel fireplaces is primarily decoration,
there is indeed some heat generated by the gel fuel canisters. Each
gel fuel fireplace item page will list BTU information, which can be
approximated as follows: 35 BTUs = ...
Our Answer:
For most applications, a base pan, burner ring, shutoff valve, and
decorative media will be needed. However, you will need to determine
the diameter of the it, if you want match lighting, manual ignition or
an electric ignition of the sys...
Our Answer:
No, FMI pipe can indeed only be used with an appropriately-listed FMI
or Vantage Hearth woodburning fireplace. You would need another brand
of class A chimney pipe, such as DuraTech or SuperPro. Please fill out
our Chimney Pipe Design & Q...
Our Answer:
In my opinion, the Stove Bright Metallic Rich Brown Stove Paint [1]
has the most bronze to it, with the Honey Glo Brown Stovebright Stove
Paint [2] being a close, but lighter second. I have seen both of these
colors in person and the meta...
Our Answer:
Yes, please see it below: Innsbrook Large Direct Vent Gas Fireplace
Insert - Natural Gas [1]
From Section Page: Gas Fireplace Inserts [2]
ID: gas-fireplace-inserts
Links:
------
[1] http://www.efireplacestore.com/cui-dv35in33ln.html...
Our Answer:
We do carry the Stove Bright #6309 metallic black paint. Here's a
link: Stove Bright metallic paint [1].
From Section Page: Stove Paint & Fireplace Paint [2]
ID: paint
Links:
------
[1] http://www.efireplacestore.com/cpf-43210.html
[...
Our Answer:
No, all of our propane gas log sets require a safety pilot kit. We do
not offer any propane match light log sets.
From Section Page: Propane Gas Fireplace Logs [1]
ID: propane-gas-logs
Links:
------
[1] http://www.efireplacestore.co...
Our Answer:
While most of the river rock kits we offer are for use in select
direct vent models, you can indeed install the following vent-free
stone sets inside an existing woodburning fireplace: Alterna Vent-Free
FireStone Gas Burner Set with Remot...
Our Answer:
If you already have the mesh screen panels, we recommend the UniFlame
Adjustable Fireplace Curtain Rod Kit [1].
From Section Page: Mesh Fireplace Screens [2]
ID: fireplace-mesh
Links:
------
[1] http://www.efireplacestore.com/uf-c-6...
Our Answer:
We do have some paint that can paint the inside of a firebox but,
depending on if you are burning wood or gas, the longevity will vary.
If you are painting the inside of a fireplace that you use to burn
wood, the paint will eventually cra...
Our Answer:
We have several modern styles of direct vent fireplace that can be
vented horizontally; however, they do not all vent off of the back of
the unit. They would vent vertically, then turn 90 degrees to the
outside. Please take a look at some...
Our Answer:
We actually have 3 available. We have a Stoll 20 in. W x 17 in. D
Grate Heater [1], a Stoll 22 in. W x 20 in. D Grate Heater [2] and a
Stoll 24 in. W x 22 in. D Grate Heater [3].
From Section Page: Wood Burning Fireplaces [4]
ID: wood...
Our Answer:
Unfortunately, there are no covers available for the decorative fire
pit rings. We apologize for this inconvenience.
From Section Page: Fire Pits [1]
ID: fire-pits
Links:
------
[1] http://www.efireplacestore.com/fire-pits.html
Our Answer:
Yes, you will need 6" stainless steel liner to vent our wood-burning
inserts. Please note that you need to make sure that your existing
fireplace is listed to accept the particular model that interests you,
and that the insert itself is a...
Our Answer:
We do not sell any black fireplace valve keys and floor covers.
However, please see the following unpainted valve covers and keys that
can be painted black with any good quality metal paint (such as
Rustoleum and Valspar): Dante Plain (Un...
Our Answer:
Most stoves will have a build plate affixed to the rear of the unit,
which should contain a model number and serial number for reference.
From Section Page: Wood Stoves [1]
ID: wood-stoves
Links:
------
[1] http://www.efireplacestore...
Our Answer:
All of our wood-burning fireplaces can also be used to install gas
logs inside. To answer your question, yes, this is something that is
very common. The key is to get a "wood-burning fireplace" that is
listed to burn wood and vented accor...
Our Answer:
You would need a complete replacement, as vent-free appliances cannot
be converted for fuel type. Please reply with your full fireplace
dimensions (front width, rear width, opening height, depth, etc.), as
well as how you want to control ...
Our Answer:
For your application, a 50" by 33" tri-fold screen would be best. A
couple examples of screens that would be suitable are the Napa Forge
Small 3 Fold Traditional Arch Fireplace Screen [1] and the Black 3
Panel Colonial Fireplace Screen [2...
Our Answer:
Because both of these units are smooth faced and do not require this
metal to be uncovered, it is certainly possible to install a
decorative marble surround over the facades. Please let me know if I
can assist you in any other way.
From...
Our Answer:
It is unlikely that you will be able to change the log set on a
direct vent model, as these units are specifically tested and designed
for the log set that was included at purchase. To find the model
number, you should be able to locate a...
Our Answer:
The only product on the market that can be used with a masonry
fireplace is a grate heater. An example is the Stoll 20 in. W x 17 in.
D Grate Heater for Vented Gas Logs [1]. The heater would take the
place of your current grate and would ...
Our Answer:
Per your fireplace dimensions, I would recommend either an 18" or 20"
log set. This recommendation is based upon what burner would be
appropriate for your application. Our least expensive style is our
Post Oak [1] log set.
From Section...
Our Answer:
Based on your description, you will need a manufactured fireplace,
rather than a fireplace inserts. As you noticed, inserts are designed
to retrofit into a masonry chimney and must be vented vertically. They
are simply meant to make the e...
Our Answer:
Indeed, most vented gas logs can be converted from one gas type to
another. The required conversion pieces vary with manufacturer and log
set size. Vent-free log sets, on the other hand, cannot be converted.
From Section Page: Gas Logs...
Our Answer:
Usually, the logs in the set would be slightly larger than the ring,
so the burner flame will engulf the logs, rather than surround them at
the perimeter. Before purchasing another set of gas logs, we'd suggest
that you verify the measure...
Our Answer:
Vent free appliances have an elevation restriction of 4,500 feet. Due
to the lack of oxygen, they suffer from frequent pilot outages at any
higher elevation. These units must also only be used as a supplemental
heat source. Because of oxy...
Our Answer:
We are sorry, but we do not sell ventless gas log burners by
themselves, only vented.
From Section Page: Gas Log Burners Only [1]
ID: gas-log-burners-only
Links:
------
[1] http://www.efireplacestore.com/gas-log-burners-only.html
Our Answer:
We do offer several wood burning fireplaces that are equipped with
gas line "knockouts." This would allow you to route a gas line into
the unit and utilize a log lighter or gas log burner.
From Section Page: Fireplaces [1]
ID: firepl...
Our Answer:
Depending on the amount of dust in the air, the fan motor can become
clogged and will require cleaning. To inspect the motor, you will need
to use an Allen key to remove the set screw in the fan hub. The fan
blade assembly can then be rem...
Our Answer:
No, wood stoves are designed to use single- or double-wall stovepipe
from the top of the stove to the ceiling or wall of the room where the
stove is installed. At that point (ceiling or wall), you transition to
double- or triple-wall Clas...
Our Answer:
No. For proper venting, you must use the direct vent pipe (coaxial,
pipe-within-a-pipe) specified in your owner's manual.
From Section Page: B-Vent Fireplaces [1]
ID: b-vent-fireplaces
Links:
------
[1] http://www.efireplacestore.co...
Our Answer:
We recommend using a poly brush on this liner, such as this Schaefer
Round Chimney Cleaning Brush [1].
From Section Page: FasNSmooth Chimney Liners [2]
ID: fasnsmooth-chimney-liners
Links:
------
[1] http://www.efireplacestore.com/c...
Our Answer:
Unfortunately, we do not have any inserts that are ready made to fit
arched applications. One would have to install a standard insert and
then custom fit a flashing between the insert and the arched mantel.
From Section Page: Gas Firepl...
Our Answer:
No, we only sell new products and do not purchase used items to
re-sell.
From Section Page: Fireplace Mantels [1]
ID: fireplace-mantels
Links:
------
[1] http://www.efireplacestore.com/fireplace-mantels.html
Our Answer:
Before proceeding further, please double check to be sure the pilot
is adjusted properly in respect to the thermocouple. If the pilot
flame is too small or not aimed properly, it will not engulf the upper
third of the thermocouple or ther...
Our Answer:
Per the manufacturer, original stock of the log set for this unit is
no longer offered and unfortunately, there is not a direct replacement
that is made. Due to issues with sooting and overheating, they do not
recommend trying to retrofit...
Our Answer:
We are not a Heat N Glo dealer, so we cannot get this part for you.
Please contact a local dealer or Heat N Glo directly.
From Section Page: Fireplace Panels and Liners [1]
ID: fireplace-panels-and-liners
Links:
------
[1] http://ww...
Our Answer:
Both the direct vent and vent free gas inserts we carry are very
efficient. The direct vent range from 75 to 85 percent efficient,
while the vent free are 99 percent efficient.
From Section Page: Gas Fireplace Inserts [1]
ID: gas-fire...
Our Answer:
Here are the two inserts that are approved for mobile home use that
we currently offer. Osburn 1100 [1] Osburn 2200 [2]
From Section Page: Wood Burning Fireplace Inserts [3]
ID: wood-burning-fireplace-inserts
Links:
------
[1] http:...
Our Answer:
The primary concern will be the distance from the top of the opening
to your roof. Each vent-free unit will have a minimum distance
required for this measurement, and these vary from model to model.
This information can be found in the ow...
Our Answer:
Ventless logs are indeed safe, but there are a few factors to
consider before purchasing. Please read our article with plenty of
information about ventless gas logs and how they compare to vented gas
logs; you can read it by clicking the ...
Our Answer:
Making the change to a Duraplus chimney system would require a
masonry transition plate, which is designed to be used in conjunction
with the appropriate slip connector and flexible liner assembly.
From Section Page: Chimney Liners [1]...
Our Answer:
While there are some fireplace inserts on the market that can use
some outside air for combustion, I am not aware of a unit that is
truly direct vented and can allow for no inside combustion air to be
used. These units must all be vented ...
Our Answer:
We have a wall-mounted direct vent fireplace that may interest you;
please see it below: Napoleon WHD31 Plazmafire Wall-Mounted Gas
Fireplace [1]
From Section Page: Gas Fireplaces [2]
ID: gas-fireplaces
Links:
------
[1] http://www.e...
Our Answer:
The biggest grate we sell has a front width of 42.5" and the same
back width. It is 17" deep. If this will fit your firebox, this would
be our recommendation: Pilgrim Twelve-Bar Rectangular Steel Fireplace
Grate with Center Leg - 4.5 Inch...
Our Answer:
If the pilot frame is going far beyond the thermocouple probe, the
pilot may be adjusted too high. The gas valve assembly will have a
slotted adjustment screw, which can be used to lessen the pilot
output. However, this must be done in sm...
Our Answer:
There are a few options available. You may choose from either our
Princess [1], Bonaparte [2], or our Georgian [3] for rear vent
applications.
From Section Page: Gas Fireplaces [4]
ID: gas-fireplaces
Links:
------
[1] http://www.efi...
Our Answer:
No, the only elbows made for FMI's double wall class A pipe (8" inner
diameter and 12 3/8" outer diameter) is a 30-degree elbow. These are
sold in sets of two, and you can see the elbow kit here: FMI Wood
Fireplace 30 Degree Elbow for FMI...
Our Answer:
Our largest outdoor fireplaces are 44" models, though we have both a
gas vent-free unit and a wood-burning model. You can see them below:
FMI Berlin Lights 44\" Linear Vent-Free Outdoor Fireplace - Natural
Gas [1] Monessen SB Outdoor Radi...
Our Answer:
The Napoleon fireplace inserts we carry are tested and listed by
InterTek, which is a testing agency similar to UL. However, the
inserts must be installed into a properly maintained masonry fireplace
or approved zero clearance manufacture...
Our Answer:
Your entire unit must be replaced, as vent-free appliances cannot be
field-converted to the other fuel type. We can offer suggestions on a
replacement vent-free fireplace system (box and logs), or a
replacement ventless log set (if you pu...
Our Answer:
Very little heat is generated by a gel fuel fireplace. This type of
fireplace is more for ambiance.
From Section Page: Wall Mounted Fireplaces [1]
ID: wall-mounted-fireplaces
Links:
------
[1] http://www.efireplacestore.com/wall-moun...
Our Answer:
A 7" chimney flue with no obstructions will accept a 6" reline pipe
with no problems. However, depending on your locality and the type of
appliance that you are venting, you may need an insulation kit for the
liner you are installing. The...
Our Answer:
Please see our Chimney Pipe Design & Quote Form [1]. If you fill out
the form with the appropriate information, we will provide a quote in
one business day with a complete list of items needed.
From Section Page: DuraTech Class A Chimn...
Our Answer:
The only item we have that will cover both the width and height you
provided will be the Pilgrim Traditional Rumford Fireplace Spark Guard
- 50 Inch x 49 Inch [1].
From Section Page: Fireplace Screens [2]
ID: fireplace-screens
Links:...
Our Answer:
If your plumber believes the problem to be electrical, it may be an
issue with the gas valve itself. This is often the only component that
requires electrical power to operate.
From Section Page: Gas Fireplace Inserts [1]
ID: gas-fire...
Our Answer:
This depends on the manufacturer and model of your log set.
From Section Page: Gas Log Valves and Safety Pilots [1]
ID: gas-log-valves-and-safety-pilots
Links:
------
[1]
http://www.efireplacestore.com/gas-log-valves-and-safety-pilo...
Our Answer:
This varies from manufacturer to manufacturer. By and large, the
measurement refers to the front width of the fireplace face, including
the sides, but in other cases it is the opening measurement. For every
fireplace on our website you ca...
Our Answer:
Because these units use oxygen from within the home for combustion, a
vent free fireplace cannot be used as the sole source of combustion.
Dangerously low oxygen levels can result if the unit malfunctions. I
would recommend using a "heate...
Our Answer:
Certain models of high efficiency wood and pellet stoves did indeed
qualify for a federal tax credit. These units had to be purchased and
installed by the end of 2011. Currently, I do not have any information
as to if this credit will be ...
Our Answer:
Any of our high heat stove or fireplace paints would be suitable for
this type of refinish. Assuming you need black paint, we offer a flat
black and satin black versions. These can be seen at the following
links: Stove Paint 1 [1] Stove P...
Our Answer:
I am not aware of a vent free fireplace that would meet this height
requirement. Typically, vent free units have a shorter opening, due to
their 40,000 BTU limitation. The extra height would leave a lot of
void space that the burner assem...
Our Answer:
In order to receive an ANSI certified burner as part of your log set,
a unit with the letter "A" must be indicated after the burner part
number. An example is the Real Fyre 24\" Charred Oak ANSI Certified
Vented Natural Gas Logs Set with ...
Our Answer:
While we do not carry a truly vent free system for outdoor use, it is
possible to use a vented system in a vent free box, as long as it is
in an outdoor area with good airflow.
From Section Page: Outdoor Gas Logs [1]
ID: outdoor-gas-l...
Our Answer:
We offer only a few see-thru wood burning units: Monessen Designer
Radiant See-Thru Wood-Burning Fireplace with Black Doors - 42 Inch
[1]. Monessen Designer Radiant See-Thru Wood-Burning Fireplace - 36
Inch [2].
Links:
------
[1] http:/...
Our Answer:
The vast majority of our replacement brick panels are produced for
specific fireplaces. However, we do have a couple that can be cut down
to size. Please follow the below link to view one of these items.
Hargrove Panels [1]. If this optio...
Our Answer:
For hanging screens, it would be best to measure the width and height
of the individual screen panels, as this is how the replacements are
advertised. Some screens include the approximately 1/2" of height
added by the hanging screen rings...
Our Answer:
As a retailer, we do not sell the brass tools separate from the
stand.
From Section Page: Individual Fireplace Tools [1]
ID: individual-fireplace-tools
Links:
------
[1] http://www.efireplacestore.com/individual-fireplace-tools.html
Our Answer:
If a new ventless log set is purchased, it will come as a complete
assembly. The set will have all the needed components, including the
decorative embers. Installation costs vary from region to region.
From Section Page: Ventless Gas Lo...
Our Answer:
Class A chimney will most likely not be an option for your
installation. I suspect that your stove pipe vents up and turns 90
degrees into a brick chimney. If this is the case, you will need to
continue using single walled black stovepipe...
Our Answer:
While we do not offer such a device, some home automation suppliers
offer low voltage/millivolt thermostats than can be utilized in this
way. I recommend checking with a distributor of these products, such
as SmartHome.
From Section Pag...
Our Answer:
No, the FMI Venice Lights direct vent fireplace [1] does not have any
gas log options at this time. You can only use the decorative glass
options provided by the manufacturer inside that model.
From Section Page: Propane Gas Fireplace ...
Our Answer:
Unfortunately, the largest reducer we carry will only adjust sizing
by 2 inches. It is recommended not to undersize a stove outlet more
than 2 inches, as a further decrease can cause the stove to overdraw
and burn through its fuel supply ...
Our Answer:
No, our gas logs require a compatible burner that will include a
grate for the logs.
From Section Page: Gas Logs Only - No Burner [1]
ID: gas-logs-only---no-burner
Links:
------
[1] http://www.efireplacestore.com/gas-logs-only---no-...
Our Answer:
No, the Monessen DIS33 [1] does not have an option for a glass front
because it is a vent-free unit that must be open to the room to allow
combustion air into the firebox. Likewise, all vent-free gas
appliances disallow the use of glass d...
Our Answer:
Unfortunately, no. We only offer black Thurmalox paint. We apologize
for this inconvenience.
From Section Page: Stove Paint & Fireplace Paint [1]
ID: paint
Links:
------
[1] http://www.efireplacestore.com/paint.html
Our Answer:
We can identify this with the manufacturer and model information for
the log set. This should be located on the burner itself or attached
to it with a data plate.
From Section Page: Gas Logs [1]
ID: gas-logs
Links:
------
[1] http://...
Our Answer:
Unfortunately, no. Vent-free gas appliances cannot be field-converted
for fuel type. We apologize for this inconvenience.
From Section Page: Fireplace Adaptors & Conversion Kits [1]
ID: fireplace-adaptors---conversion-kits
Links:
--...
Our Answer:
The electric fireplaces we offer from Fire Sense can be mounted under
a television. However, the manufacturer recommends having at least 3
feet from the top of the fireplace to the nearest combustilbe material
such as electrical cords, fu...
Our Answer:
Unfortunately, no. Vent-free log sets are engineered to operate in a
very specific manner with very specific accessories. Glass can only be
used with a vent-free unit if the unit were engineered to be used with
glass. Burners designed for...
Our Answer:
From the information that you have provided, I feel comfortable
recommending the Empire Tahoe Premium Direct Vent Propane See-Thru
Fireplace. You can find a link to it below. Direct Vent Propane
See-Thru Fireplace [1] If this does not fit...
Our Answer:
Based on your dimensions, a 20-inch outdoor log set could be used in
your fireplace. One popular set is the Real Fyre 20\" Post Oak Outdoor
Propane Gas Logs Set with Safety Pilot Kit [1]. The log grate and
burner assembly is manufactured ...
Our Answer:
We do sell a variety of see-thru gas log sets without a pilot kit.
Please see our full selection here: See-Thru Gas Logs [1]
From Section Page: Propane Gas Fireplace Logs [2]
ID: propane-gas-logs
Links:
------
[1] http://www.efirepla...
Our Answer:
Unfortunately, we no longer offer log sets that are configured for
use with gel fuel. The sets we carry will only be fueled by natural
gas or propane fuel. We do offer these in vent free configurations as
well.
From Section Page: Gel F...
Our Answer:
This unit is able to use any listed wood burning fireplace insert,
with the addition of a chimney liner. I was unable to provide the
actual firebox dimensions for this unit. If you will provide the front
width, rear width, depth, and heig...
Our Answer:
We offer the Real Fyre line of logs, manufactured by R.H. Peterson.
These sets are among the most realistic in the industry, featuring
highly detailed ceramic refractory logs and an advanced burner system
with your choice of control valve...
Our Answer:
While we have a wide variety of gas log sets available, only a pair
of styles fit all of your criteria. These two styles are available in
two different varieties. Please follow the below links to check them
out. Evening Fyre - 18\" [1]. E...
Our Answer:
If you are installing a pre made spark arrestor screen, it can
generally be installed by removing the lid of the chimney cap, then
sliding the mesh into place. It is usually designed to expand and hold
itself in position. If you using non...
Our Answer:
If you could please provide the manufacturer's name and model of your
fireplace, we could check availability of exact fit replacement doors.
I look forward to hearing back from you.
From Section Page: Fireplace Specific Fireplace Doors ...
Our Answer:
Depending on your model, the a replacement pull screen assembly may
still be available. If you can reply with your full model number and a
shipping zip code, we can advise on pricing and availability.
From Section Page: Mesh Fireplace ...
Our Answer:
The primary by-products from a vent-free burner are water vapor and
carbon dioxide. The clean-burning technology minimizes exhaust. For
more information, please see the "Vent-Free" section of our Gas
Fireplace and Stove Buying Guide [1]. ...
Our Answer:
We carry fireplace screens for flat openings. We do not have any that
are right angled.
From Section Page: Fireplace Screens [1]
ID: fireplace-screens
Links:
------
[1] http://www.efireplacestore.com/fireplace-screens.html
Our Answer:
While we do have a couple of see-thru linear, direct vent gas
fireplaces that may interest you, our largest has a 50" total width.
Please see our options below: Napoleon LHD50 Linear Series Gas
Fireplace [1] *In the "Select Configuration"...
Our Answer:
One of the best options available for your fireplace would be the
Portland Traditional II Textured Black Glass Fireplace Door Assembly -
51 Inch x 30 Inch [1]. Please note that the door assembly is shown in
brushed brass, but is available...
Our Answer:
Yes. The 36 inch width is the standard size for these see-thru vent
free fireboxes. In fact, that is the only size we carry.
From Section Page: See-Thru, Island, & Peninsula Fireplaces [1]
ID: see-thru---peninsula-fireplaces
Links:
-...
Our Answer:
If a particular grate for a Majestic model is still available, we can
indeed special order it for you through the manufacturer.
From Section Page: Fireplace Grates [1]
ID: grates
Links:
------
[1] http://www.efireplacestore.com/grat...
Our Answer:
Our smallest vent-free option would be a reduced-depth coal burner,
such as this: Rasmussen Vent-Free Natural Gas Burner with Realistic
Coals - 13\" - C9A-SE-N [1] For log sets, here is the smallest we
offer: Real Fyre 16\" Valley Oak Ven...
Our Answer:
Unfortunately, your vent-free fireplace cannot be field-converted to
natural gas. The entire unit would need to be replaced, as vent-free
appliances are designed only for use with the fuel type they are
shipped ready to use.
From Secti...
Our Answer:
No, a pellet stove can only utilize wood pellets for fuel and will
not have provisions for a gas connection or a gas log set. We
apologize for this inconvenience.
From Section Page: Gas Logs Only - No Burner [1]
ID: gas-logs-only---n...
Our Answer:
If you are planning to install a direct vent insert into a
brick/masonry fireplace, we recommend this model: Small Monessen
Reveal Direct Vent Gas Fireplace Insert with Cottage Clay Firebrick
[1]. This model will fit in the dimensions you...
Our Answer:
If you want to use the propane, you will need to choose a direct vent
or vent-free stove, such as these: Direct Vent: Napoleon Arlington
Direct Vent Cast Iron Gas Stove [1] Vantage Hearth Oxford Cast Iron
Direct Vent Gas Stove [2] Vent-Fr...
Our Answer:
Currently, we only have door overlays listed on our site. We can
special order doors for specific brands and models. First determine
the manufacturer name, model number, and serial number.
From Section Page: Stove Accessories [1]
ID: ...
Our Answer:
All of our remote controls include the hand-held transmitter and the
remote receiver, which is wired to the valve of the fireplace/stove.
From Section Page: Remote Controls [1]
ID: remote-controls
Links:
------
[1] http://www.efirep...
Our Answer:
If you have a direct vent, vent-free or B-vent fireplace, you cannot
switch out the log set and burner that came with the unit. However, if
you have a gas log set installed inside a wood-burning fireplace
(masonry or manufactured), then t...
Our Answer:
No, pellet vent pipe (class L pipe) is not tested or listed to
withstand the higher flue temperatures of a wood fire. We apologize
for this inconvenience.
From Section Page: Direct-Temp Pellet Pellet Vent Pipe [1]
ID: direct-temp-pel...
Our Answer:
One byproduct of combustion is water vapor. Gas log sets produce a
higher amount of water vapor when operating, when compared to a wood
burning fire. The issue can be exacerbated by higher levels of
relative humidity inside the house. Bec...
Our Answer:
Unfortunately, I have not come across a wood-burning stove that could
be used in a two sided configuration such as this. Every unit we carry
is designed specifically to work in a one sided application.
From Section Page: Napoleon Firep...
Our Answer:
Per the manufacturer, as long as the surface of the stove has been
cleaned, a primer is not necessary. Primer would only be needed with
the 1,200 degree paint if a layer of corrosion or baked on dust is
present that would not be easily re...
Our Answer:
One of our most popular models of unvented propane fireplace inserts
is the Medium Innsbrook Vent-Free Gas Fireplace Insert with Millivolt
Controls [1]. This unit offers remote ready controls and is capable of
heating approximately 800 sq...
Our Answer:
We only have a small selection of wood stoves that feature cook tops.
One option is, of course, the 1150. However, we could add a cook top
option to our NPL-1400. Please follow the below links to check out
this option. NPL-1400 [1]. Cook ...
Our Answer:
Vestal does not offer the poker catch as an individual piece at this
time. The catch is only sold in conjunction with the replacement poker
arm, seen here [1]. I apologize that we do not have this item
individually.
From Section Page: C...
Our Answer:
The size feature on the search menu for these inserts is based on
width. For our best recommendation for a gas insert, please reply with
your preference between direct vent and vent-free, as well as your
full fireplace dimensions (front w...
Our Answer:
Unless you live in a mobile or modular home, a fresh air kit is
usually not required with a manufactured woodburning fireplace. For
more information, please check with the manufacturer.
From Section Page: Venting Kits [1]
ID: venting-...
Our Answer:
Unfortunately, no. Our largest rectangular rug is this 24 Inch x 48
Inch Goods of the Woods Tan Rectangular Guardian Hearth Rug [1].
From Section Page: Hearth Rugs [2]
ID: hearth-rugs
Links:
------
[1] http://www.efireplacestore.com...
Our Answer:
No, it is not a good idea to install logs that are not made by the
manufacturer of the burner that you currently have. If you have
ventless or vent-free gas logs, you will need to get identical
replacements. If it is a vented set, there m...
Our Answer:
While we do not have any premanufactured fireplace screens that will
cover an opening of your size, we have the option us having a screen
custom fabricated to fit your needs. The custom screens are a flush
type that fit against the firepl...
Our Answer:
While uncommon, this natural vent fireplace insert can create an
unpleasant smell under certain circumstances. One of the following
issues may be occurring: 1. The unit is new and the paint used in
production of the unit is still curing. ...
Our Answer:
While we do offer several reduced depth coal and log baskets that are
meant for coal burning fireplaces, the fireplace opening must be at
least 9 inches deep to accommodate them. A depth of 6 inches is very
shallow, even for a coal burnin...
Our Answer:
We do not carry any see-thru/multi-sided electric fireplaces, but we
do offer some contemporary-style direct vent gas models. Please see
the following for an example: Majestic 42 Inch Echelon See-Thru Wide
View Direct Vent Gas Fireplace w...
Our Answer:
The maker of the Dante gas valves does have a certification for their
products. As such, the Dante valves on our site will carry the CSA
certification, which is usually the required certification for use in
California, Massachusetts, and ...
Our Answer:
In order to utilize both real and faux logs in an outdoor fireplace,
you would need to utilize a stainless steel log lighter such as this
one: Stainless Steel Log Lighter [1]. This item is basically a single
tube burner assembly that can ...
Our Answer:
The Majestic CDVT42 direct vent fireplace has a BTU rating of 17,000
to 24,000 for the natural gas model [1] and 18,000 to 24,000 for the
propane model [2].
From Section Page: Majestic Fireplaces [3]
ID: majestic-fireplaces
Links:
-...
Our Answer:
Replacement of the door assembly will depend on the type of fireplace
that you have. Do you have a true masonry fireplace with a surface
mounted door assembly, or a manufactured fireplace with a bifold door
assembly?
From Section Page:...
Our Answer:
The following fireplaces utilize accent lighting Monessen Belmont 36
Inch Clean Face Direct Vent Signature Command Fireplace [1] Monessen
BDV500 42 Inch Convertible Direct Vent Signature Command Fireplace [2]
Studio Luxury Direct Vent Gas...
Our Answer:
Yes, we do. Here is one example: Real Fyre See Thru 18\" Evening Fyre
Ventless Natural Gas Logs Set with Variable Flame Remote Pilot Kit [1]
This is also available for propane [2] models.
From Section Page: See Thru Gas Logs [3]
ID: ...
Our Answer:
You should allow for a minimum clearance of 3 to 5 inches at the
front and sides of the grate.
From Section Page: Fireplace Grates [1]
ID: grates
Links:
------
[1] http://www.efireplacestore.com/grates.html
Our Answer:
Most commonly, you would use a "ceiling support box" and a "DSA roof
flashing" to make the transition from interior to exterior. I am
assuming the underside of the metal roof will be exposed or there is
will be only a layer of sheathing w...
Our Answer:
Our smallest woodburning fireplace is a 36" model, please see the two
versions of it here: FMI Bungalow - Builder 36 Inch Circulating Wood
Burning Fireplace [1] FMI Bungalow - Builder 36 Inch Radiant Wood
Burning Fireplace - Smooth Face [...
Our Answer:
We do sell several models of portable patio heaters. You may view
these models at the links below: Patio Heaters [1] Please let me know
if I can assist you in any other way.
From Section Page: Fire Sense Patio Heaters [2]
ID: fire-sen...
Our Answer:
Likely not. A poorly drafting fireplace is usually caused by one of
the following problems: 1. Chimney flue is poorly insulated (cold
hearth syndrome). 2. Chimney flue is too large for the opening. 3.
Chimney is too short. 4. Obstruction ...
Our Answer:
We do not recommend trying to purchase universal replacement
accessories such as these, as any direct vent fireplace is
specifically tested and listed for use only with what the manufacturer
provides. Please contact Watson's for more info...
Our Answer:
We need your full fireplace dimensions (front width, rear width,
opening height, depth, etc.) as well as what type of insert you need
(full-bodied direct vent insert, full-bodied vent-free insert, vented
gas log set or ventless gas log se...
Our Answer:
Yes, a universal replacement panel can be cut to size and used as the
floor for your firebox. We recommend this Hargrove refractory panel:
Hargrove Replacement Fireplace Refractory Panel - 24 inch X 28 inch
[1]. This panel is 3/4" thick a...
Our Answer:
The best way to protect a wooden mantel is by using a fireplace hood.
We have several sizes and styles of hoods that can mount according to
your needs.
From Section Page: Gas Logs [1]
ID: gas-logs
Links:
------
[1] http://www.efirep...
Our Answer:
Unfortunately, the only 4" pipe that we carry is specified for gas or
pellet usage.
From Section Page: Stove Pipe [1]
ID: stove-pipe
Links:
------
[1] http://www.efireplacestore.com/stove-pipe.html
Our Answer:
The type of liner you need will depend on what kind of stove or
insert you get. Generally, a 6" stainless steel liner would be needed
for a wood stove or insert (installed into an existing brick/masonry
fireplace), while a pellet stove wo...
Our Answer:
We do indeed stock some 10" inner diameter single-wall 24-gauge black
stovepipe. Please see the link below for the 24" length of this pipe:
24 inch stovepipe [1].
From Section Page: Stove Pipe [2]
ID: stove-pipe
Links:
------
[1] htt...
Our Answer:
The Black Texture 42 inch Cabinet Door Frame [1] is in stock and
would ship the next business day. This color is the only option on our
site. This item would ship free to your ZIP code, and it would take
approximately three business days ...
Our Answer:
We carry both freestanding outdoor linear fire pits, like the
Napoleon Linear Patioflame Gas Fire Pit [1], as well as linear fire
pit kits that can be installed outdoors, like the Hearth Products
Controls 60 Inch Stainless Steel Linear Tr...
Our Answer:
If the existing chimney for the wood stove is in good condition, it
will be acceptable to line the chimney and continue to use the same
termination. The liner can be supported at the top of the chimney
using "L" brackets or HVAC strapping...
Our Answer:
There are some manufactured gas fireplaces that can be configured for
an indoor/outdoor see through application. However, we do not offer
any wood burning models that are equipped in this way. The primary
issue is with the lack of insulat...
Our Answer:
We are unable to determine whether this pipe is still available.
While we do not carry a pipe with these specs, it is possible it is
still available through a manufacturer that we do not sell. We
apologize for this inconvenience.
From ...
Our Answer:
Unfortunately, not. Wood burning inserts may only be installed into
full masonry, wood burning fireplaces or specifically approved
pre-fabricated wood burning appliances.
From Section Page: Wood Burning Fireplaces [1]
ID: wood-burning...
Our Answer:
Napoleon developed the Timberwolf line of stoves as a more affordable
alternative to their existing line of stoves. The Timberwolf platform
is one similar to the Ford Model T - no frills, the stoves work well
and burn fuel efficiently, bu...
Our Answer:
We do offer several outdoor deck mats that are larger than the 24 x
48 size you mention. A couple of examples are the Goods of the Woods
36 Inch x 48 Inch Rectangular Protective Deck Mat - Black [1] and the
Goods of the Woods 54 Inch Roun...
Our Answer:
The largest 42" wide direct vent gas fireplace we offer is the
Monessen Covington Clear View Direct Vent Gas Fireplace with Signature
Command Control System - 60 Inch [1]. While it is listed as a 60"
model, the viewing area is 42" wide an...
Our Answer:
Yes, the cost to replace your manufactured fireplace with a vent-free
unit should be considerably cheaper, even when factoring in the cost
to run a gas line to the fireplace and removal of the original. We
offer several vent-free fireplac...
Our Answer:
An aluminum liner can be used to vent a gas furnace as long as the
liner is being routed through an existing masonry chimney. Flue gases
from a gas furnace are not corrosive enough to warrant the use of a
stainless steel liner.
From Sec...
Our Answer:
Yes, you can indeed use an appropriately-rated stove board on your
carpet for a wood stove. Please check the manufacturer information of
your stove to see what the R-value requirements are for an appropriate
stove board. This information ...
Our Answer:
Screw on type handles can be replaced if broken, but it will depend
on the model and manufacturer of the set. If you are looking to change
the color of the handles, I will definitely require this information,
as most manufacturers use dif...
Our Answer:
There are a number of locations where the build tag may be located on
the unit: 1. On the exterior smoke shelf. Left or right side. 2.
Within the fireplace interior, on the upper left or right side behind
the fireplace screens. 3. In the ...
Our Answer:
Ideally, for safety, the screen will cover the entire opening of the
fire box. You may consider this arched screen [1].
From Section Page: Fireplace Screens [2]
ID: fireplace-screens
Links:
------
[1] http://www.efireplacestore.com/f...
Our Answer:
Our largest model for gas would be 62" wide (the Napoleon 62\" Linear
Direct Vent Natural Gas Fireplace - 50,000 BTU [1] ) and our largest
wood fireplace measures about 50" wide (the FMI Plantation Floor Level
Mosaic Masonry Woodburning F...
Our Answer:
We do have a few gas starter pipes that will fit your need, though
the exact item will depend on the gas type and where the gas line
enters the firebox. Please see these items: For Natural Gas: Natural
Gas Starter 1 [1] Natural Gas Starte...
Our Answer:
If you have a masonry/brick fireplace, you can install a woodburning
insert. To see our full selection, please see below: Wood Burning
Fireplace Inserts [1] All of our models require a 6" diameter
stainless steel liner to be connected to ...
Our Answer:
We have a few traditional-looking wooden mantels with a shelf depth
that meets your preference. Please see these mantels: Fireplace Mantel
1 [1] Fireplace Mantel 2 [2] Fireplace Mantel 3 [3] Fireplace Mantel 4
[4] Please let us know if yo...
Our Answer:
Yes, provided you have the necessary dimensions to fit one, you can
use any of the UniFlame hexagonal fireplace grates.
From Section Page: Fireplace Grates [1]
ID: grates
Links:
------
[1] http://www.efireplacestore.com/grates.html
Our Answer:
Unfortunately, no. The metal frames for the hearth pads we sell are
cut and welded together on site by the manufacturer. It would be
necessary to purchase angled steel to construct your own frame or have
a local fabricator cut the steel c...
Our Answer:
Given your dimensions, our Valley Oak line of logs would need to be
used. This set is specifically designed for installation in fireplaces
with limited width and depth. The Real Fyre 16\" Valley Oak Ventless
Natural Gas Logs Set with Safe...
Our Answer:
Generally, vent free logs will have a more sophisticated burner
assembly that will allow them to operate without a vent to the
outdoors. The burner is designed so that a specific amount of fuel is
metered to each burner port. This allows ...
Our Answer:
Our top brands include Napoleon (wood and gas), Monessen (wood and
gas), Majestic (wood and gas), FMI (wood and gas), Empire (gas), and
Vantage Hearth (wood and gas). A general rule of thumb for BTUs and
heating area is 35 BTUs per square...
Our Answer:
We have a few closed-combustion chamber models that combine
efficiency with the capability to provide heat to a large home. For
example, please see the Napoleon Prestige NZ-26 [1], the Osburn
Stratford [2] or the Napoleon NZ3000 [3]. By t...
Our Answer:
Yes, please see the BLDV400NSC7 below: Monessen Belmont 36 Inch Clean
Face Direct Vent Signature Command Fireplace - Natural Gas [1]
From Section Page: Monessen Fireplaces [2]
ID: monessen-fireplaces
Links:
------
[1] http://www.efir...
Our Answer:
Depending on your unit, there are a few places the manufacturer
information may be located. If you have a woodburning fireplace, the
first location would be a metal plate that is on the left or right
side of the smoke shelf bracket, right...
Our Answer:
While we do not have anything exactly this size, you may be
interested in our Pilgrim 39 Inch x 31 Inch Forged Iron Fireplace
Screen with Straight Doors - Matte Black [1]. This type of screen
frames your opening.
From Section Page: Fire...
Our Answer:
If not specified by the manufacturer, it is recommended to have at
least a 6 inch apron of protection around the fire pit. In your case,
that would mean a 44" x 44" square. Unfortunately, we do not offer a
square deck mat in this size. We...
Our Answer:
The base footprint for the La Costa measures 49"x25" at the top and
bottom. The Granite measures 54"x28", so there is just a bit of an
overhang, and no additional support is needed.
From Section Page: Patio Tables with Fire Pits [1]
I...
Our Answer:
Unfortunately, no. The state of California prohibits the installation
of vent-free gas appliances. An alternative would be a direct vent
insert [1]. This option would require the relining of your chimney,
though.
From Section Page: Ven...
Our Answer:
Per your dimensions, 24 inch ventless gas logs would offer the better
fit.
From Section Page: Ventless Gas Logs [1]
ID: ventless-gas-logs
Links:
------
[1] http://www.efireplacestore.com/ventless-gas-logs.html
Our Answer:
It appears that you have a log lighter, not a gas burner. Log
lighters use gas to assist in burning real wood logs, whereas a gas
burner would use a ceramic or refractory log set.
From Section Page: Fireplaces [1]
ID: fireplaces
Lin...
Our Answer:
My apologies, but I am not familiar with this brand. We do have free
standing screens that can sit directly in front of any fireplace, but
anything that attaches directly to the unit would be purpose built by
the manufacturer.
From Sect...
Our Answer:
This chances of this happening are very low. If a direct vent
fireplace insert is used, this could not occur, as the unit will be
completely sealed with a pane of glass. All combustion air comes from
the outdoors and exhaust gases are ven...
Our Answer:
The only major item that has been added to these sets is the
inclusion of an oxygen depletion sensor. This system will cause the
unit to shut down should oxygen levels in the room drop below safe
levels.
From Section Page: Gas Log Valve...
Our Answer:
The general rule of thumb is for vent pipe to be installed male end
down. So, the liner would go inside the flue outlet. Of course, most
factory boxes require specific brands of pipe that feature locking
tabs and ensure a proper fit/conne...
Our Answer:
We do offer the CTCL vent-free log set, but it requires the use of
the appropriately-sized Triple-Play Burner system. Please reply with
your fireplace dimensions (front width, rear width, depth and height),
and we provide a quote for the ...
Our Answer:
After locating an owner's manual for this particular unit, it does
not advise that vent free logs are acceptable for use in this unit.
However, it is certainly feasible to install a set of vented gas logs,
as the unit is equipped to deal ...
Our Answer:
Because wood and gas stoves will have much different surface
temperatures, different motors are used in each Ecofan to optimize
performance. The gas stove fans are designed to start operating at a
lower temperature and are not designed to...
Our Answer:
Some customers have successfully converted their wood burning stoves
to gas units. However, it can prove to be difficult. Things to
consider prior to such a conversion are the need to remove the stove
door (as a gas set cannot be operated...
Our Answer:
A lintel mount hood would be installed on an existing lintel on a
fireplace. If you have a lintel, it will be located beneath the bricks
at the top of the firebox. A lintel mount hood will attach to the
lintel with screws.
From Section...
Our Answer:
This will depend on the manufacturer and model number of the insert.
Some manufacturers offer decorative fronts and surrounds, while others
do not.
From Section Page: Gas Fireplace Inserts [1]
ID: gas-fireplace-inserts
Links:
------...
Our Answer:
One our more popular vent-free sets can be seen at the link below:
Vent-Free Fireplace [1] Real Fyre log sets are among some of the most
realistic that are currently available. This set is designed to fit a
see-thru fireplace up to 36 inc...
Our Answer:
We have this screen that may interest you: Fireplace Screen Option
[1]. If not, please browse our full selection of fireplace screens
below: Fireplace Screens [2].
From Section Page: Fireplace Screens [3]
ID: fireplace-screens
Links:...
Our Answer:
We do not carry any multi-sided inserts at this time, though we do
have some see-thru zero clearance gas models. If you have a
brick/masonry fireplace, you can install one of these inside your
existing fireplace if there is enough room fo...
Our Answer:
The majority of our direct vent fireplaces average heat output
between 30,000 and 40,000 BTU, but this output is directly related to
size. Output varies for gas type, as well - either natural gas or
propane.
From Section Page: Direct V...
Our Answer:
Unfortunately, none of our direct vent see-thru models have ceramic
glass - only tempered. We apologize for the inconvenience.
From Section Page: See-Thru, Island, & Peninsula Fireplaces [1]
ID: see-thru---peninsula-fireplaces
Links...
Our Answer:
Yes, we recommend a direct vent unit and an accompanying corner
mantel. Please see some suggestions below: Empire Tahoe Deluxe Direct
Vent Propane Fireplace - 32 Inch [1] Empire EMBC1S Corner Wooden
Mantel Cabinet with Base - For 32 Inch ...
Our Answer:
These panels are indeed a pair of 24 inch screens, for a total width
of 48 inches.
From Section Page: Mesh Fireplace Screens [1]
ID: fireplace-mesh
Links:
------
[1] http://www.efireplacestore.com/fireplace-mesh.html
Our Answer:
Vent-free appliances are not recommended for homeowners with any
respiratory issues, particularly asthma. For more information on this
and other factors to consider, please see the "Vent-Free" section of
our Gas Fireplace and Stove Buying...
Our Answer:
Yes. We can special order that for you. Simply give us a call and we
will assist you.
From Section Page: Mantel Shelves [1]
ID: mantel-shelves
Links:
------
[1] http://www.efireplacestore.com/mantel-shelves.html
Our Answer:
Yes, all of our manufactured wood-burning fireplaces [1] must use
manufactured Class A chimney pipe [2]. The chimney pipe must run
vertically and terminate at least three feet over the roof, and even
higher if there are any obstructions w...
Our Answer:
We have several models that you can use for your application. Please
see our full selection of patio fireplaces below, then use the search
options on the left-hand side of the page to select "Vent-Free" in the
"Vent Type" category: Patio ...
Our Answer:
Virtually all of Napoleon's line of 36 inch direct vent fireplaces
may be used in conjunction with a power vent. Several larger models
may be used as well. A list of item numbers is as follows: BGD36CFNTR
GD36NTR BGD36NTR HDX40 GD80 GD70 ...
Our Answer:
Unfortunately, we do not offer any remote-operated log lighters, only
the standard models that must be manually lit. You can see our full
selection in the Fire Starters [1] section on this website.
From Section Page: Wood Burning Firep...
Our Answer:
Unfortunately, no. All wood burning inserts require the removal of
any existing door enclosure, as the insert will have a sealed door of
its own that must be readily accessed. The insert must also be able to
readily radiate heat to the ro...
Our Answer:
The unit you have pictured is a manufactured type of fireplace, which
will likely not accommodate a gas fireplace insert. However, gas logs
could be installed into the existing fireplace without an issue. For
better heat output and a diff...
Our Answer:
Our ventless gas logs do offer the option to add a hand-held remote
control that offers both on/off functionality as well as a thermostat.
However, none of our sets control the pilot light itself. We have
millivolt valves that have on/off...
Our Answer:
This unit is not meant to be used with B-vent pipe. Because it is a
direct vent unit, it must pull its air from an outside source. The FMI
direct vent piping is designed to perform that task. While B-vent pipe
could theoretically be used ...
Our Answer:
We do have some high-temp black spray paint that you can use to touch
up your firebox. Please be advised, however, that if you have a
wood-burning fireplace, the paint will eventually crack and peel due
to the extreme heat. Please see the...
Our Answer:
As long as the gas insert is sized properly to the wood-burning
fireplace, installation is fairly straightforward. Gas lines for the
unit are generally run by a plumber. In some cases, the same plumber
can complete the entire installation...
Our Answer:
This is likely an ash dump drawer into which you can sweep ashes from
the fireplace. The ashes should then be cleaned from the outside of
the home through an access door (usually located on the exterior of
the masonry chimney.)
From Se...
Our Answer:
That is correct. Vent free appliances are not recommended above 4,500
feet of elevation. Because of lower oxygen levels, the ODS will
frequently cause pilot outage. A vented unit is the best type of
appliance for higher elevations.
From...
Our Answer:
A B vent type of fireplace certainly can be replaced with a direct
vent model. However, the venting system is different. A larger direct
vent pipe, usually 7 inches in diameter, must be used. If you have a 9
inch by 9 inch area to contain...
Our Answer:
We do indeed offer two 6" barometric dampers; the Copperfield
Automatic Barometric Damper With Black Tee - 6-Inch Diameter [1] and
the Vogelzang 6\" Barometric Damper for 6\" Single-Wall Flue Pipes
[2]. As this items are made by different...
Our Answer:
In order to heat the required space, a unit that generates at least
26,000 BTUs would be required. A couple of options would be the Empire
Tahoe Premium Direct Vent Propane Fireplace with Standing Pilot - 36
Inch [1] and the Monessen HBDV...
Our Answer:
In order to choose an insert, you will need to measure the front
width, rear width, depth (front to back), and height (bottom of
opening to top of opening). For more information, please see our
Fireplace Insert Buying Guide [1].
From S...
Our Answer:
Yes, we do have a wood stove that you can rear-vent into an existing
fireplace. Please see this model: Wood Stove [1] You will want to make
sure that the clearances listed in the owner's manual for that stove
(which is downloadable on tha...
Our Answer:
We are not currently a dealer for Blaze King stoves, but do carry
several other brands. If you would like to provide your criteria, I
will be happy to check into a stove that may match your needs.
From Section Page: Wood Burning Stoves ...
Our Answer:
Because the burner pan lays flat upon the fireplace floor, I do not
recommend running the gas line in this way, unless the line is against
the back wall of the fireplace and out of the way.
From Section Page: Gas Logs [1]
ID: gas-logs...
Our Answer:
While we do not have "fireplace adaptors" per se, we do have tees
designed for use with our liner kits. For example, the below tee
features a removed 10" take off: Ultra Pro Tee [1] This tee requires a
separately purchased cap: Tee Option...
Our Answer:
Several fireplaces have a very modern appearance: Alterna Vent-Free
FireGlitter Heating System - Natural Gas [1]. Alterna Vent-Free
FireShape Gas Burner Set with Remote Control - Natural Gas [2].
Napoleon WHVF31 Plasmafire Wall-Mounted Ve...
Our Answer:
Most wood stoves will have a metal build tag fastened to the back of
the stove body. The tag may be located beneath a heat shield, which
will likely need to be removed to see the tag clearly.
From Section Page: Napoleon Wood Stoves [1]
...
Our Answer:
For the fireplace inserts that we sell, and most other models that
are available, it is not necessary to run the blower. The blower is
simply an accessory that can be used to heat a room more rapidly or
extend the reach of the insert whil...
Our Answer:
We do indeed offer replacement broom heads for fireplace tool sets.
Please follow the below link to check out one of our options.
Replacement Broom Head [1].
From Section Page: Fireplace Tool Sets [2]
ID: fireplace-tool-sets
Links:
-...
Our Answer:
No, none of our paint will withstand direct contact with flames, nor
the high temperatures of a wood fire.
From Section Page: Stove Bright Paint [1]
ID: stove-bright-paint
Links:
------
[1] http://www.efireplacestore.com/stove-brigh...
Our Answer:
The fireplace facings and surrounds that we carry are all intended to
be used with specific models of fireplaces and inserts. You will
definitely need to know that manufacturer name and model number of the
fireplace to determine what part...
Our Answer:
It is best to match a brush to your pipe diameter. A 6" round flue
takes a 6" brush. Over-sizing the brush results in the brush bristles
folding over which reduces their cleaning ability.
From Section Page: Chimney Cleaning Products [1]...
Our Answer:
Unfortunately, no. None of our fireplace grates [1] attaches directly
to our firebacks.
From Section Page: Firebacks [2]
ID: firebacks
Links:
------
[1] http://www.efireplacestore.com/grates.html
[2] http://www.efireplacestore.com/f...
Our Answer:
It would be ideal for you to seal the chimney top, but we only offer
damper-style chimney caps for square/rectangular flues that could
achieve this.
From Section Page: Chimney Products [1]
ID: chimney-products
Links:
------
[1] http...
Our Answer:
While some fireplaces will have a built in ash tray or drawer when
built, I am not aware of a "drop in" ash collection tray. I apologize
that we do not carry such a product.
From Section Page: Fireplace Insert Panels and Liners [1]
ID...
Our Answer:
After checking with the manufacturer, they have advised that they did
not produce a 1400 wood burning insert. This was a free standing
stove, with a pedestal base. They did produce a 1401 insert, which
could possibly be what you have. Eit...
Our Answer:
Unfortunately, all models of wood stove that we offer currently are
top vented only. This is characteristic of the EPA, non catalytic
stoves that are manufactured now.
From Section Page: Vantage Hearth Wood Stoves [1]
ID: vantage-hea...
Our Answer:
You're most likely interested in one of our double-bottom ash
buckets. For example, our Napa Forge Vintage Iron Ash Bucket with Lid
[1] features a dual bottom for added durability and reduced heat
transfer. All the same, you should never ...
Our Answer:
Concrete refractory logs tend to hold up better than their ceramic
counterparts and will also radiate heat. Other than differences in
appearance, these would be the only primary differences between the
two.
From Section Page: Outdoor Ga...
Our Answer:
One of our standard 6" round brushes would do the trick. For example,
our Schaefer [1] round brush is perfect for this application.
From Section Page: DuraFlex Chimney Liners [2]
ID: duraflex-chimney-liners
Links:
------
[1] http://...
Our Answer:
Indeed, they can. Our Peterson burner assemblies offer a cap on the
left side that can be swapped with the gas inlet on the right. Adding
a control valve to the burner assembly can however increase the
difficulty of this modification.
...
Our Answer:
Unfortunately, we do not currently offer a wood-burning insert that
fits your dimensions. The smallest insert we carry requires a firebox
width measurement of 25".
From Section Page: Wood Burning Fireplaces [1]
ID: wood-burning-firepl...
Our Answer:
Unfortunately, the largest manufactured shelf that we currently offer
measures out to be 72" in overall width. At this time, we do not have
a supplier that can custom make a larger shelf than this, due to
shipping limitations.
From Sect...
Our Answer:
No, this decorative add-on log kit is only an aesthetic-enhancement
item for the Napoleon HD81 see-thru direct vent fireplace [1].
From Section Page: Decorative Inserts [2]
ID: decorative-inserts
Links:
------
[1] http://www.efirepl...
Our Answer:
Most likely, the fireplace is no longer generating enough voltage to
allow the thermostat to function properly. This can be due to a weak
thermocouple or thermopile. Another issue may be the wiring connection
at the gas valve itself. You ...
Our Answer:
For gas logs, a local plumber should be able to do the installation.
We recommend calling around and quoting the job to a few different
plumbers.
From Section Page: Vented Gas Logs [1]
ID: vented-gas-logs
Links:
------
[1] http://ww...
Our Answer:
The only line of vent-free fireplaces we carry that come complete
with a mantel (as one item) are the 26\" Vail Special Edition [1]
line. We have other models, like the Napoleon GVF36 [2], that have
accompanying mantels that are custom-ma...
Our Answer:
The procedure will vary based on the type of ignition system your
fireplace has. If you have your owner's manual for the fireplace, this
information will be on the front cover. If not, there will be a build
plate that is located in the bo...
Our Answer:
The length is 40" and width is 49".
From Section Page: Hearth Boards & Stove Boards [1]
ID: hearth-boards
Links:
------
[1] http://www.efireplacestore.com/hearth-boards.html
Our Answer:
It is very possible that the 23ef022gra will fit into your existing
unit, as many manufacturers intend for the gel fuel and electric
inserts to be interchangeable. However, I was unable to find
information on the model 061506 you mentione...
Our Answer:
Unfortunately, no. The only birch-style gas logs we sell are vented.
We apologize for the inconvenience.
From Section Page: Ventless Gas Logs [1]
ID: ventless-gas-logs
Links:
------
[1] http://www.efireplacestore.com/ventless-gas-lo...
Our Answer:
If your fireplace's flue is in good working order, it is indeed
possible to use either a vented or vent free log set. Vented logs will
offer a more realistic appearance, but are largely for aesthetics.
Vent free logs are very efficient an...
Our Answer:
Yes. The gas line will need to run inside the firebox for connection
to a ventless gas log set [1].
From Section Page: Vent Free Fireplaces [2]
ID: vent-free-fireplaces
Links:
------
[1] http://www.efireplacestore.com/ventless-gas-l...
Our Answer:
Unfortunately, Empire does not offer additional logs or ember kits
for their vent-free stoves. This is usually the case for all vent-free
appliances, as nothing can be added to the original log/ember set-up
as described in your owner's ma...
Our Answer:
Generally, the width of the front log determines the size of the log
set you currently have. Another way to measure the width is to check
the length of the burner pipe from end to end, outside the burner pan
itself.
From Section Page: G...
Our Answer:
The only fireplaces we offer for use with propane are direct vent,
vent-free and B-vent models. Please see our Gas Fireplace and Stove
Buying Guide [1] for more information.
From Section Page: Fireplaces [2]
ID: fireplaces
Links:
--...
Our Answer:
Unfortunately, I do not have a cap in these exact dimensions.
However, I do have caps that are slightly smaller and can be attached
to the top of the chimney, rather than around the outer perimeter.
From Section Page: Chimney Caps [1]
...
Our Answer:
The use of a wood burning insert within a manufactured fireplace can
indeed be a fuzzy subject. In order to be able to use the insert, both
the manufacturer of the insert and the manufactured fireplace must
specifically state that they ca...
Our Answer:
Yes, this paint is suitable for use inside a gas firebox. However, it
will not withstand direct contact with flames, nor the heat of a
wood-burning fire.
From Section Page: Rutland Stove Paint & Fireplace Paint [1]
ID: rutland-stove-p...
Our Answer:
If it is a masonry fireplace, we do indeed have some doors that can
be customized to fit your opening. Please see this link for our full
selection of doors: Fireplace Doors [1]. Using the search menu on the
left-hand side, you will see th...
Our Answer:
While we do not offer any such shroud or surround, we do have some
glass door assemblies that can fit your opening: Portland Traditional
II Textured Black Glass Fireplace Door Assembly [1] Portland
Traditional II Polished Brass Glass Fire...
Our Answer:
Yes, the LX36 and LX32 models use a millivolt ignition system that
does not require electricity to operate. As you mentioned, the only
part affected by a power outage would be the blower, but the fireplace
would be able to be operate.
...
Our Answer:
Yes, it is quite normal for a mantel above a fireplace to get hot. As
long as the mantel clearances for your fireplace model are met, you
should have no reason for concern. A couple of options would be to get
a hood for your fireplace, or...
Our Answer:
The Napoleon 1600C Series Cast Iron Wood Burning Stove [1] is the
only model we sell that can be converted to a rear-vent flue.
From Section Page: Wood Burning Stoves [2]
ID: wood-burning-stoves
Links:
------
[1] http://www.efirepla...
Our Answer:
In some cases, vent free appliances can produce this type of
byproduct if they have an operational issue or are in need of service.
The film is likely a thin layer of hydrocarbons that have not burnt
completely with the fuel. It is recomm...
Our Answer:
Most of our vent free fireboxes will have a front overall width and
depth that is similar to your needs; however, they range from 20 to 26
inches in overall depth and do not have the option for a liner with a
stone appearance.
From Sec...
Our Answer:
The AA batteries will be located inside the remote receiver box,
which is installed behind a wall plate or inside the bottom of the
appliance. The receiver box will have a manual slider that switches
the receiver between off, remote, and ...
Our Answer:
I would first check any data plate numbers or part numbers that are
affixed to the unit. This information will likely tell which you have.
Vented systems will have a high flame and most will have a large ember
bed. The logs will usually n...
Our Answer:
The TC36N FMI Tudor direct vent fireplace [1] uses the FMI BK model
squirrel-cage blower [2].
From Section Page: Fireplace Panels and Liners [3]
ID: fireplace-panels-and-liners
Links:
------
[1] http://www.efireplacestore.com/fsd-tc3...
Our Answer:
We do have some options that are close to that size, but we need a
bit more information before we can make a recommendation. Do you
currently have a vent-free firebox and need a ventless gas log set, or
do you have a brick/masonry firepla...
Our Answer:
There are no vent-free gas fireplace media cabinets available, due to
the amount of clearance required for a vent-free gas fireplace around
the opening, and especially over the top opening (where the vast
majority of heat emits).
From ...
Our Answer:
Vent-free appliances are not currently allowed for use in the state
of California. You would be limited to a direct vent or natural vent
appliance instead.
From Section Page: Empire Fireplace Inserts [1]
ID: empire-fireplace-inserts
...
Our Answer:
Flexible 8 inch liners are relatively easy to install. Depending on
the size of your damper, you may be able to pull the liner up from
below, which is the best route to pursue. A rope can be dropped down
the chimney and tied to the liner....
Our Answer:
We do not offer a stock piece that makes this conversion, but if you
reply with your fireplace model and piping information, we will be
happy to research available options for this purpose, if applicable.
From Section Page: Gas Vent Pi...
Our Answer:
While we do sell some replacement parts for existing products, I do
not have a square pan with those dimensions. Do you have any
manufacturer information or a model number for the item? This may
allow me to special order something for you...
Our Answer:
If your Heatilator model is a vent-free gas insert then yes, you
should leave the screen on at all times. If it is a wood-burning
insert, you can remove the screen.
From Section Page: Fireplace Insert Doors and Screens [1]
ID: firepl...
Our Answer:
The Real Fyre burners that we have available on our website are only
designed to be used with appropriate Real Fyre log sets. If you could
reply with the dimensions of the fireplace pictured, we can recommend
several replacement sets that...
Our Answer:
All vent-free appliances are equipped with an oxygen-depletion sensor
(ODS) that will automatically shut off if oxygen levels in the room
drop. This is built in to the pilot assembly of all of our vent-free
fireplaces and stoves and is no...
Our Answer:
Depending on if you have a wood burning fireplace or a gas fireplace,
you will have varying success with our high-temperature paint.
Whenever you paint the interior of a wood burning fireplace, the
high-temp paint we sell will eventually ...
Our Answer:
There is sometimes confusion when people use the term "insert." If
you are referring to an insert that slides into an existing fireplace,
no, we do not currently offer any two-sided inserts. We do, however,
carry several two-sided zero cl...
Our Answer:
Both of these items have been recently discontinued by the
manufacturer, however they are still in stock at our warehouse. The
items can be seen on our webpage at the following links: Majestic
Textured Black Manor Rectangular Front with L...
Our Answer:
Unfortunately, we do not provide parts for the Ecofan models. Please
contact the manufacturer directly at 1-800-567-3556 for more
information. We apologize that we are unable to assist you with this.
From Section Page: Caframo Ecofans ...
Our Answer:
If you are looking for gas logs only, we need to know the kind of
burner you are currently using in the two-sided fireplace. If you have
a Peterson Real Fyre burner, we will be able to suggest some
replacement log options. Otherwise, we c...
Our Answer:
All of our wood stoves have a top-vent flue collar.
From Section Page: Wood Burning Stoves [1]
ID: wood-burning-stoves
Links:
------
[1] http://www.efireplacestore.com/wood-burning-stoves.html
Our Answer:
You have a few options to consider, depending on if your fireplace is
a brick/masonry unit or a manufactured (metal) model. If you prefer,
please reply with your full fireplace dimensions (front width, rear
width, opening height, depth, e...
Our Answer:
The FMI Alpine outdoor vent-free systems that we sell utilize a
millivolt ignition with a standing pilot. If this is the case for your
model, you can use any millivolt remote control. A basic example can
be found below: SkyTech 1001 Milli...
Our Answer:
The grate you're looking for is our model 26430 [1] 7-bar grate.
From Section Page: Fireplace Grates [2]
ID: grates
Links:
------
[1] http://www.efireplacestore.com/cpf-26430.html
[2] http://www.efireplacestore.com/grates.html
Our Answer:
In order to make this conversion, the appropriate length of flexible
liner, connection tee, support plate, clamps, and cap will be needed.
A short run of single or double wall chimney connector will also be
needed to span the gap from the...
Our Answer:
Per the manufacturer, the predominant colors for this rug are maroon
red, beige and black.
From Section Page: Hearth Rugs [1]
ID: hearth-rugs
Links:
------
[1] http://www.efireplacestore.com/hearth-rugs.html
Our Answer:
Ventless and vented fireplace inserts both have their own set of
advantages and drawbacks. Vented fireplaces use no room air for
combustion and give a realistic flame pattern, but are not as
efficient as a vent free insert and individual ...
Our Answer:
Generally, yes. If the unit is a brand that we have access to parts
to, it is possible to special order a replacement sensor.
From Section Page: Natural Gas Fireplace Logs [1]
ID: natural-gas-logs
Links:
------
[1] http://www.efirep...
Our Answer:
Fireboxes require a clearance from the edges of surrounding mantel
legs and shelf. Clearances from the surrounding combustible material
and how far the material can project from the wall will depend on how
far back the firebox is set into...
Our Answer:
Unfortunately, we do not have a fireplace screen suitable for your
application; all of ours are for standard, one-sided fireplaces. We
apologize for this inconvenience.
From Section Page: Fireplace Screens [1]
ID: fireplace-screens
...
Our Answer:
There are a few primary differences between vented and ventless logs.
First, the vented logs will need to utilize an existing, functioning
chimney. Ventless logs can be used with no chimney at all; you simply
close the damper in the firep...
Our Answer:
The manufacturer, Mirage Stone, has a web link that displays large
color swatches of the available materials. Please view the link below
to have a look at these options: MIrage Stone color swatches [1]
Please let me know if I can assist y...
Our Answer:
We do not carry direct vent fireplaces that come with a mantel as a
standard package. However, almost every manufacturer that we offer has
accessory mantel cabinets and surrounds available.
From Section Page: Fireplaces with Mantels [1]...
Our Answer:
We carry individual hooks that allow you to hang tools, such as the
Minuteman Wrought Iron Single-Hook Tool Hanger [1], however we do not
offer a complete wall hanging tool set at this time.
From Section Page: Fireplace Tool Sets [2]
...
Our Answer:
For a vent-free, see-thru type of installation, you will indeed need
only the unit itself, along with a burner and log assembly. You can
then finish either side of the unit with mantels and finishing
materials of your choosing. Please vie...
Our Answer:
As far as capping the 8 x 12 flue tile goes, the Gelco 8 in. x 13 in.
[1] cap could be adjusted to work. However, I am unsure of how your
5-inch liner is currently supported. It is possible to attach this cap
over an existing top plate, i...
Our Answer:
Generally, yes. If you would like to provide the model number of the
fireplace, I will be happy to check into the availability of the
hearth panel.
From Section Page: Majestic Fireplace Inserts [1]
ID: majestic-fireplace-inserts
Link...
Our Answer:
There are two ways to determine the usability of a chimney after a
creosote fire. The first is to hire an inspection company to drop a
remote camera down the entire length of the chimney to look for any
cracks or perforations that resulte...
Our Answer:
This will depend on the diameter of the gas pipe that is feeding the
fireplace. You will need to measure the exposed end of the pipe to
verify if the inside diameter is 1/2" or 3/4", as both sizes are
commonly used.
From Section Page: F...
Our Answer:
In order to provide recommendations for a woodburning insert, please
reply with the following information: Is the existing fireplace a
brick/masonry unit? What is the front width (left to right), rear
width, depth (front to back) and open...
Our Answer:
I apologize for the difficulty in locating this stove. We do indeed
carry this model, which can be seen here [1].
From Section Page: Fireplaces [2]
ID: fireplaces
Links:
------
[1] http://www.efireplacestore.com/npl-gds26.html
[2] h...
Our Answer:
If you are looking at installing a full-bodied direct vent insert,
you will need an appropriate, compatible vent kit. In most cases, this
would be two co-linear (side-by-side) aluminum liners.
From Section Page: Gas Fireplace Inserts [...
Our Answer:
We offer brick surrounds in brick red, burnt red and desert sand. The
colors are listed in each item's title on this page.
From Section Page: Chimney Surrounds [1]
ID: chimney-surrounds
Links:
------
[1] http://www.efireplacestore.c...
Our Answer:
No, all pellet inserts are only suitable with wood pellets, not wood
logs, and all woodburning inserts are only suitable for logs, not wood
pellets.
From Section Page: Wood Burning Fireplace Inserts [1]
ID: wood-burning-fireplace-ins...
Our Answer:
I have not come across a riser system for placing a gel log outside
the fireplace opening. I apologize that I do not have this product to
offer.
From Section Page: Fireplace Mantels [1]
ID: fireplace-mantels
Links:
------
[1] http://...
Our Answer:
While finding a propane, vent-free unit with an electronic ignition
is rare, we do offer this model: Napoleon WHVF31 Plasmafire
Wall-Mounted Vent-Free Gas Fireplace [1] This is a wall-mounted unit,
and if you need an insert--a unit that s...
Our Answer:
Depending on your unit, you may or may not be able to install an
electronic ignition. Please reply with the manufacturer and model
information of your fireplace/insert, and we will research available
options for you.
From Section Page:...
Our Answer:
It is very likely that a blower can be added to your Napoleon
fireplace. To recommend the correct blower, we would need the model
number of your appliance.
From Section Page: Napoleon Fireplaces [1]
ID: napoleon-fireplaces
Links:
--...
Our Answer:
Most of the brick liner panels are held in place by metal retaining
brackets at the top of the fireplace. The rear panel will need to be
positioned first, then the side panels slide into position against the
rear panel, holding it upright...
Our Answer:
B-vent and natural vent fireplaces are the same. For this type of
fireplace, the combustion air is drawn from the room and the products
of combustion are expelled through the chimney. Please visit our Gas
Fireplace and Stove Buying Guide ...
Our Answer:
We do indeed offer complete liners kits for most needs. Will you be
venting a wood-burning appliance or a unit that burns coal or oil? The
type of alloy needed will depend on the fuel being used.
From Section Page: Chimney Liners [1]
...
Our Answer:
The logs themselves don't turn red, only the embers in the burner
pan.
From Section Page: See Thru Gas Logs [1]
ID: see-thru-gas-logs
Links:
------
[1] http://www.efireplacestore.com/see-thru-gas-logs.html
Our Answer:
Our high-heat stove paint is not suitable for use in a masonry
wood-burning fireplace. The high heats from the wood fire will cause
the paint to peel and crack.
From Section Page: Stove Paint & Fireplace Paint [1]
ID: paint
Links:
-...
Our Answer:
My apologies, but we do not carry a hearth rug that is as long and
narrow as the one you have now. Are narrowest rectangular rugs are 22
inches in width and 44 inches in length. Again, I am sorry that we do
not have an exact replacement.
...
Our Answer:
Yes, we do offer some universal refractory panels that will work for
your woodburning fireplace. These panels have a straight gray brick
pattern. Please see the following links: One 24\"h x 28\"w Panel [1]
Two 24\" h x 40\"w Panels [2] Th...
Our Answer:
Depending on the size of the B-vent piping that is installed, you may
be able to leave the B-vent stack in position and run the new direct
vent piping through the stack. However, it is necessary to remove the
existing B-vent piping and re...
Our Answer:
These fire pits feature an anodized aluminum ring between the burner
bowl and the granite table top. This trim ring provides an insulating
barrier that keeps the granite cool.
From Section Page: Patio Tables with Fire Pits [1]
ID: pat...
Our Answer:
Monessen, who purchased Majestic, still has many of the old Majestic
part. Much of what you could need down the road may be available.
From Section Page: Monessen Fireplaces [1]
ID: monessen-fireplaces
Links:
------
[1] http://www.ef...
Our Answer:
This fire glass is designed for use on a Real Fyre glass burner. It
can be used in conjunction with the Peterson Real Fyre River Rock Fyre
Stones Geo Shapes [1] on a vented burner.
From Section Page: Fire Glass Only - No Burner [2]
I...
Our Answer:
While none of our high-temperature paint is recommended for use
inside of a wood-burning firebox, if you have a gas fireplace, you may
be able to use this: stove paint [1]
From Section Page: Stove Paint & Fireplace Paint [2]
ID: paint...
Our Answer:
In almost all cases, it is not necessary to use refractory cement
when building the enclosure for your fire pit. However before we can
determine this you will need to know the BTU output of the burner that
you will be using and how close ...
Our Answer:
Per the published information for this stove, it is indeed possible
to vent this model into a clay lined masonry chimney, as long as the
clay tiles are proven to be in good condition. The combustion fan will
provide adequate positive pres...
Our Answer:
Unfortunately, the largest see-thru ventless log sets we offer are
24". Please see the following for an example: Real Fyre See Thru 24\"
Evening Fyre Split Ventless Propane Gas Logs Set with Variable Flame
Remote Pilot Kit [1]
From Sect...
Our Answer:
Yes, efficiency information is usually documented on each insert's
item page, under the "Item Description." Vent-free inserts always
provide 99.9% efficiency, as the heat generated by the fuel is not
lost through a chimney. For more infor...
Our Answer:
If the unit came equipped to use a gas burner, it is likely that
there is a specific set of gas logs that must be used with the unit.
Do you know the manufacturer name and model of the fireplace? There
should be a build plate either on th...
Our Answer:
None of our ventless gas log sets have a blower option. If you have a
manufactured wood-burning fireplace, there may be a blower available
for that model that you can use in conjunction with a ventless log
set.
From Section Page: Ventl...
Our Answer:
In order for our ventless see-thru logs to fit properly, a minimum
width of 22 inches is required. While the log assembly would fit into
a slightly smaller space, it is likely that the valve will be too
close to the sides of the fireplace...
Our Answer:
Unfortunately, no. Due to the dangers that can occur when a vent-free
log set is improperly converted, manufacturers do not offer conversion
kits for these units. An entirely new burner assembly would need to be
used instead.
From Secti...
Our Answer:
Yes, you can. You need to make sure you select the proper size.
From Section Page: Vent Free Fireplaces [1]
ID: vent-free-fireplaces
Links:
------
[1] http://www.efireplacestore.com/vent-free-fireplaces.html
Our Answer:
Unfortunately, we do not carry a product for this use. Is your unit
an open faced or sealed version and is it gas or wood? There may be an
issue that is causing the air leakage or another alternative to seal
it.
From Section Page: Firep...
Our Answer:
Per the manufacturer, this kit is still available. However it will be
a special order item.
From Section Page: Vantage Hearth Fireplaces [1]
ID: vantage-hearth-fireplaces
Links:
------
[1] http://www.efireplacestore.com/vantage-heart...
Our Answer:
We do not have a screen that matches the height you require. Most are
an inch or two taller. If you will provide the color and style that
interests you, we will be happy to make some recommendations.
From Section Page: Fireplace Screens...
Our Answer:
We would be happy to assist you, but we need a little more
information. Do you currently have a traditional gas log set within a
masonry fireplace, or do you have one within a factory-built
fireplace? If you have a factory-built unit, did...
Our Answer:
Vent-free gas appliances do produce water vapor, particularly those
that use propane as opposed to natural gas. For this reason, we advise
potential consumers to be aware of possible condensation on windows
and moisture that can collect o...
Our Answer:
The Vantage Hearth fireplace hoods are model-specific (not
universal), and will only attach to their compatible Vantage Hearth
fireplaces. We do have some universal hoods, including the Elite
Square End Fireplace Hood with Lintel Mount - ...
Our Answer:
If your glass fireplace cover is an operable door assembly, you will
need to measure from the outside to the outside of the assembly. If
the cover is a fixed pane of glass, you will want to measure to the
metal on either side of the glass...
Our Answer:
The original FK24 fan system that was offered for this unit is no
longer available. However, the Majestic FK12 Fireplace Fan Kit - For
Direct Vent and Wood Burning Fireplaces [1] is also an option for this
unit. The fan can be equipped wi...
Our Answer:
For removal of light deposits, a mixture of water and vinegar can be
used as a nonabrasive solution to wipe down the glass. A cotton cloth
can be used to do this. For heavier deposits, I recommend using a
cleaner such as the Stove Bright ...
Our Answer:
Unfortunately, we do not have any doors that can be made to this
size. We apologize for this inconvenience.
From Section Page: Portland Willamette Fireplace Doors [1]
ID: portland-willamette-fireplace-doors
Links:
------
[1]
http://...
Our Answer:
This will depend primarily on the firebox. Many fireboxes can operate
without the brick panels, as they are decorative in most cases.
However,you will need to provide the manufacturer name and the model
number of the fireplace for us to v...
Our Answer:
In order to size up the proper log set for your needs, we will need
the following dimensions: Front opening width Rear opening width Depth
Height (at front of opening) These measurements will give all the
information needed for the proper...
Our Answer:
Indeed, a top-vent application that has a one or two foot rise before
elbowing 90-degrees through a wall is preferable to a rear-vent.
However, in most cases a 14" rear-vent run is perfectly acceptable and
should work fine, as the normal ...
Our Answer:
We do not have a log set small enough to fit your fireplace. The logs
cannot be cut but the sizing issue has to do with the burner and
safety of use.
From Section Page: Vented Gas Logs [1]
ID: vented-gas-logs
Links:
------
[1] http:/...
Our Answer:
Hearth rugs may be made of various materials, but they will always
have fire resistance treatment in common.
From Section Page: Hearth Rugs [1]
ID: hearth-rugs
Links:
------
[1] http://www.efireplacestore.com/hearth-rugs.html
Our Answer:
We do. The Rutland 1,200 Degree Black Stove Paint - 1 Pint [1] is the
brush on version of this paint and can be applied without a primer.
From Section Page: Stove Bright Paint [2]
ID: stove-bright-paint
Links:
------
[1] http://www.e...
Our Answer:
Yes, Majestic makes an open-corner direct vent model. Please see them
below: Majestic 36 Inch Designer Right Corner Direct Vent Gas
Fireplace with Signature Command Controls - Natural Gas [1] Majestic
36 Inch Designer Right Corner Direct ...
Our Answer:
This unit used one of three door assemblies. The part numbers were as
follows: GD42PBA - Polished Brass GD42BA - Black GD42SSA - Stainless
Steel Unfortunately, all three assemblies have now been discontinued
and the manufacturer has not r...
Our Answer:
Unfortunately, the fan will not perform past its rated RPM or
amperage, so there is not an effective was to increase output from the
fan. Many models of fireplaces offer 2 or 3 fan options, with some of
the fans producing more output than...
Our Answer:
Unfortunately, we do not have the manufacturer-specific panels that
you are looking for, but we do offer some universal refractory panels
that will work for your woodburning fireplace. Please see the
following links: One 24\"h x 28\"w Pan...
Our Answer:
Unfortunately, you are correct. We do not currently carry a stove
board larger than 48" square. Further, we do not customize any of our
products. We apologize for the inconvenience.
From Section Page: Hearth Boards & Stove Boards [1]
...
Our Answer:
We may be able to help with some options for a new surround for your
direct vent fireplace. Please reply with the manufacturer and model
information and we would be happy to see what we have available for
you. We look forward to your resp...
Our Answer:
Please see the links below to our FMI Craftsman 42" options: FMI
Craftsman 42\" fireplace 1 [1]. FMI Craftsman 42\" fireplace 2 [2].
Please let us know if you have any additional questions.
From Section Page: Gas Fireplaces [3]
ID: ga...
Our Answer:
The largest standard size used in gas shutoff valves is 5/16 of an
inch. Are you able to unscrew the gas valve cover and measure the
stem?
From Section Page: Fireplace Keys and Valves [1]
ID: fireplace-keys-and-valves
Links:
------
[...
Our Answer:
The largest door opening will be on the Osburn 2400 fireplace insert.
This model has an opening size that measures 19 1/2 inches wide by 8
1/4 inches tall. Fireplace inserts typically have a small door size,
to ensure high efficiency and ...
Our Answer:
Our gas logs are only meant to be installed on a R.H. Peterson Real
Fyre gas burner, not into an existing basket like yours. We apologize
for the inconvenience.
From Section Page: Gas Logs Only - No Burner [1]
ID: gas-logs-only---no-b...
Our Answer:
Yes. If you will advise not only the manufacturer, but also the
model, we will be happy to look into the appropriate replacement
panels for you.
From Section Page: Fireplace Insert Panels and Liners [1]
ID: fireplace-insert-panels-and...
Our Answer:
Unfortunately, we do not currently offer any vent-free outdoor units
with a linear-style burner. Please note also that no vent-free unit
will have a glass front, as they need air from the surrounding area
for combustion. We apologize that...
Help Desk Software by Kayako