RSS Feed
Knowledgebase : EFS Page
 

Our Answer: Technically, yes. However, due to the fragile nature of these tiles, there is a great risk that the unit will crack and split when it is cut. The safer option would be to find a pad that does not need to be cut. From Page: CPF-03120 [1...
Our Answer: This candelabra's dimensions are 27"w x 14"h x 16"d. Please let us know if you have any additional questions. From Page: CPF-71160 [1] Manufacturer's Product Number: CH07 Our SKU: CH07 Page ID: cpf-71160 Links: ------ [1] http://...
Our Answer: This elbow is fixed. All of our double wall stove-pipe elbows will be this way. From Page: CPF-6907-DBLACK8ELB [1] Manufacturer's Product Number: 1845 Our SKU: 1845 Page ID: cpf-6907-dblack8elb Links: ------ [1] http://www.efirep...
Our Answer: This Osburn insert is a non-catalytic appliance. In fact, none of our appliances are. The only difference is the method by which the stove achieves its high efficiency, whether that be via the use of catalytic combustors or a fully lined ...
Our Answer: Yes, there are darker and lighter tones. From Page: UF-S-2092 [1] Manufacturer's Product Number: S-2092 Our SKU: S-2092 Page ID: fsd-s-2092 Links: ------ [1] http://www.efireplacestore.com/fsd-s-2092.html
Our Answer: Please refer to the product manual for the Vantage Hearth VB42I1 fireplace located on this item page. It contains a complete venting section. In Response to Question: Can I get a set of specs for chimney height with regards to nearby ...
Our Answer: No. This is the fan kit for Majestic Oxford Direct Vent Gas Stoves. I would recommend contacting the manufacturer of your stove for fan kit options. From Page: MAJ-FK26 [1] Manufacturer's Product Number: FK26 Our SKU: FK26 Page ID...
Our Answer: This liner is made specifically for FMI's Cape Cod Firebox. You may be interested in our Hargrove panels that are more universal in nature. Please follow the below link to view this option. Hargrove Replacement Fireplace Refractory Panels...
Our Answer: Yes, this RCK-M is a suitable replacement for your remote that used the RX05 receiver, if you have a Maxitrol MMVK millivolt valve. Please note that this remote is compatible with Maxitrol MMVK series millivolt valve kits and other brands...
Our Answer: Vent-free units do not have conversion kits, as they are all specifically engineered for use only either natural gas or propane. Unlike other gas appliances, they are not interchangeable with an orifice adaptor like direct vent or B-vent ...
Our Answer: In a word, yes. You may finish this unit out with non-combustible materials right up to the firebox opening. From Page: CUI-VFP32FB2EF [1] Manufacturer's Product Number: VFP-32-FB0F Our SKU: VFP-32-FB0F Page ID: cui-vfp32fb2ef Li...
Our Answer: Please find the product manual on this item page. You'll find operation instructions beginning on page 19. From Page: FSD-M36H [1] Manufacturer's Product Number: M36H Our SKU: M36H Page ID: fsd-m36h Links: ------ [1] http://www.e...
Our Answer: Sunstar currently manufactures residential heaters, such as this model, in Charlotte, NC. From Page: CUI-SC10M-1-LP [1] Manufacturer's Product Number: SC10M-1-LP Our SKU: SC10M-1-LP Page ID: cui-ck10mlp Links: ------ [1] http://w...
Our Answer: According to the dealer locator, the closest dealer is Cottingham Hardware in Alexandria, KY. They can be reached at (859) 635-2111. From Page: SBI-DB07200 [1] Manufacturer's Product Number: DB07200 Our SKU: DB07200 Page ID: sbi-d...
Our Answer: While you can indeed utilize an existing masonry chimney by using stovepipe and then a masonry thimble (if entering the chimney on the side) or simply using stovepipe and then liner (if going in through a masonry fireplace opening), this ...
Our Answer: This liner is designed specifically for FMI's Cape Cod Vent Free Firebox. It is not designed to be cut to fit any other application. You may be interested in our other liners, though. Please view them here: Hargrove Replacement Fireplace ...
Our Answer: The minimum depth you must have to install this unit into a wall is 13 1/4". Please see pages 32-33 of the owner's manual at this link: http://lib.store.yahoo.net/lib/yhst-95622685483394/npl-gd19nmanual.pdf From Page: NPL-GD19N [1] M...
Our Answer: Yes. These pipes slide together and lock with just a quarter turn. From Page: CPF-6980-SSPIPE [1] Manufacturer's Product Number: 9221SS Our SKU: 9221SS Page ID: cpf-6980-sspipe Links: ------ [1] http://www.efireplacestore.com/cp...
Our Answer: These doors are made specifically for FMI's 36" fireplaces. As such, they can not be altered. However, we do have a full selection of aftermarket doors available. Please follow the below link. Fireplace Doors [1] From Page: FSD-BD36B [2...
Our Answer: The Breckenridge VFD32FB0L Deluxe Vent-Free Louvered Gas Firebox you inquired about does not come with gas logs. This firebox can be used to house ventless gas logs, which of course are available to be purchased separately. You may find t...
Our Answer: These units can indeed be fed from either side. From Page: CUI-V368ST [1] Manufacturer's Product Number: V368ST Our SKU: V368ST Page ID: cui-v368st Links: ------ [1] http://www.efireplacestore.com/cui-v368st.html
Our Answer: Due to the inefficient nature of these circulators, it is my understanding that there are no styles that are mobile home approved. However, we do have a selection of free standing wood stoves that can be used in your application. From ...
Our Answer: No, this unit is meant to be recessed into a wall or placed into an appropriately sized mantel cabinet. From Page: CUI-VFP24FP30L10 [1] Manufacturer's Product Number: VFP-24-FP30L10N Our SKU: VFP-24-FP30L10N Page ID: cui-vfp24fp3...
Our Answer: Internal Dimensions: 54" W x 43" H Outside Dimensions: Mantel Shelf: 73-1/2" L x 6" D Height: 53-3/4" Legs: 6" W x 43" H OD Leg to Leg: 60" W From Page: FSD-ALEX5443-PG [1] Manufacturer's Product Number: ALEX5443-PG Our SKU: ALEX544...
Our Answer: You would use the silicone sealant that is included with the Lock-Top damper. From Page: CPF-09414 [1] Manufacturer's Product Number: RS875 Our SKU: RS875 Page ID: cpf-09414 Links: ------ [1] http://www.efireplacestore.com/cpf-0...
Our Answer: This product is the mantel only. To see the fireplace options that go with this mantel, please look under the accessories tab. The details for the mantel and the fireplaces can be found by downloading the product manuals on their respecti...
Our Answer: While we do not have a pull in 5 or 6 inches, we do have them available in a 4" or 7" length. Please follow the below links to view these products. Cascade 4 Inch Black Fireplace Mesh Positive Control Wand [1] Cascade 7 Inch Black Firepla...
Our Answer: This particular chimney pipe comes in lengths of 6", 12", 18", 24", 36", and 48". The options are available on the item page under the "Choose Length:" heading just above the "Add to Cart" button. From Page: CPF-709-8DTECHGAPIPE [1] M...
Our Answer: This log lighter employs 1/2" NPT fittings at its connection. From Page: PTS-LC-1 [1] Manufacturer's Product Number: LC-1 Our SKU: LC-1 Page ID: pts-lc-1 Links: ------ [1] http://www.efireplacestore.com/pts-lc-1.html
Our Answer: We are only an online retailer and have no affiliation with any local dealers. We'd be happy to fulfill an order for you and ship this item right to your door, though. From Page: CUI-S256BL [1] Manufacturer's Product Number: S25-6-BL...
Our Answer: This fireplace, the Vantage Hearth Value Line Series 42 Inch Circulating Wood Burning Fireplace with Stamped Louvers and Full Insulation, is indeed a genuine wood-burning fireplace. You can see our full selection of real wood-burning fire...
Our Answer: Unfortunately, the stove you inquired about--the US Stove Hotblast Coal and Wood Burning Furnace with Blower--is not meant for installation outdoors. The unit would rust, corrode and be inoperable after a year or two of use. From Page: ...
Our Answer: It depends on the unit. If the log set did not come with them, refer to your instruction manual or contact the manufacturer to be certain. Vent-free logs must be designed and certified to use glowing embers. This Monessen DIS33 does come ...
Our Answer: You can indeed use this Thurmalox Low-Sheen Black Paint on the inside of your wood-burning fireplace. However, please note that it will eventually peel given the extreme heat conditions and direct flame contact. That would be the case for...
Our Answer: Unfortunately, not. These units are not designed to be used in a mobile home regardless of their access to combustion air. From Page: USS-BEC95 [1] Manufacturer's Product Number: BEC95 Our SKU: BEC95 Page ID: uss-bec95 Links: --...
Our Answer: This particular electric stove has a heater rating of 4,600 BTU. From Page: FRS-60351 [1] Manufacturer's Product Number: 60351 Our SKU: 60351 Page ID: frs-60351 Links: ------ [1] http://www.efireplacestore.com/frs-60351.html
Our Answer: Yes, this heater does require vertical venting only, with Type B Gas Vent pipe. You can see the specifications for venting in the owner's manual, which can be downloaded from this item's page. The venting section begins on page 7. You can...
Our Answer: Stainless steel firebacks do not reflect more heat than cast iron firebacks. In fact, because they do not have the mass of the cast iron firebacks, the stainless steel firebacks do not radiate as much heat as the cast iron firebacks do. S...
Our Answer: Unfortunately, no, the CUI-DFS32NVC offers no optional fronts. Is there a particular style of front you were interested in? Perhaps it is offered on another one of our units. From Page: CUI-DFS32NVC [1] Manufacturer's Product Number: ...
Our Answer: While we do not carry this exact product in grey, we do offer the following product: Rutland Pre-Mixed Chimney Sweep High-Temp Furnace Cement - 1 Quart Tub [1] This product is a higher temperature version that is a thicker, sandy paste. T...
Our Answer: This item is a Concave Surround for a Napoleon BGD36CFNTR fireplace. You may view this fireplace by following the below link. Napoleon BGD36CFNTR Clean Face Direct Vent Gas Fireplace - 36-in. [1] Napoleon's BGD36CFNTR is capable of 17,000...
Our Answer: This firestop is meant to be mounted into your joists. The shield itself creates the clearance needed to pass the pipe through your ceiling, which is 2". From Page: CPF-77916 [1] Manufacturer's Product Number: 6T-JS Our SKU: 6T-JS ...
Our Answer: This unit does not come with a blower attached but one can be added to it. Blower options for this unit can be found under the accessories tab. From Page: FSD-B36L [1] Manufacturer's Product Number: B36L Our SKU: B36L Page ID: fsd...
Our Answer: The Tahoe Deluxe models will have a reversible flue collar that can be changed for your installation. You will only need to remove the sheet metal screws that secure the collar, rotate it 180 degrees, then reinstall. Pay careful attention...
Our Answer: FMI requires that a minimum clearance of 36" be maintained from the open sides of this unit to an adjacent combustibles or walls. The rear of the unit will require at least 4" from the wall. From Page: FSD-FGPN [1] Manufacturer's Prod...
Our Answer: The CUI-TSFSC is not compatible with your Chesapeake fireplace. However, the MAJ-TSMT is. Please check it out here: Ambient TSMT Touch Screen Hand-Held On/Off Remote Control [1] From Page: CUI-TSFSC [2] Manufacturer's Product Number: ...
Our Answer: This install would be pretty similar to an install in a standard wall. You'll simply frame the thimble in on the interior side of the wall. The exterior surface can then be sealed with a waterproof sealant. A custom flashing may need to b...
Our Answer: This mantel shelf is constructed of Asian hardwoods including Choi and Ash. Unfortunately, there are not any other wood options available for this mantel shelf. From Page: PRM-418 [1] Manufacturer's Product Number: 418-24 Our SKU: 4...
Our Answer: This fireplace requires FMI 8" class A chimney pipe for venting, which we do offer. Please see this link as an example: FMI Wood Fireplace 8-in. Diameter Chimney Venting Pipe for FMI Woodburning Fireplaces - 48-in. Length [1] You would ne...
Our Answer: In addition to the unit itself, you will need to select a decorative door overlay, faceplate, and faceplate trim from the accessories section on the item page. It will also be necessary to purchase a lining kit to vent the unit. This will...
Our Answer: The face of this particular fireplace will come in painted steel, unless the brushed stainless surround is selected instead. Per the manufacturer, the steel is a 24 gauge thickness. From Page: NPL-WMFE2 [1] Manufacturer's Product Numb...
Our Answer: Napoleon does not explicitly state the distance that must be maintained from the appliance to your propane tank. It will be necessary to consult with local code enforcement to determine what is the minimum/maximum distance for the tank to...
Our Answer: The blower for this insert does indeed require electricity. It comes with a 7-foot long power cord to plug in for operation. From Page: NPL-EPI-1101P [1] Manufacturer's Product Number: EPI-1101P Our SKU: EPI-1101P Page ID: naepaw...
Our Answer: The expansion section for this grate is sold separately. From Page: HYC-GT-18 [1] Manufacturer's Product Number: GT-18 Our SKU: GT-18 Page ID: hyc-gt-18 Links: ------ [1] http://www.efireplacestore.com/hyc-gt-18.html
Our Answer: Often you get more heat from a vent free unit than you do with a direct vent appliance. This is simply due to the fact that a vent free appliance has no vent through which to potentially lose heat. That being said, there are often limitat...
Our Answer: We apologize for this inconvenience. You are correct the bottom strips on these caps are "swing tabs". These hinged components can be positioned to the inside or outside of the screen for mounting. Are the tabs on your cap fixed? We'll gl...
Our Answer: This log set features 6 ceramic refractory logs. From Page: PTS-R-19 [1] Manufacturer's Product Number: R-19 Our SKU: R-19 Page ID: pts-r-19 Links: ------ [1] http://www.efireplacestore.com/pts-r-19.html
Our Answer: You are correct. Most bio fuel fireplaces use fuel cans, such as this model, or a fuel tray. The fuel would be poured into each receptacle as needed. Gel fireplaces will have individual cans that have a jellied alcohol-type fuel. From P...
Our Answer: Please note that this item includes just the stainless fireplace. The marble surround will not be included. Please download this fireplace's installation manual located on this page. Per this manual, this fireplace can indeed be installed...
Our Answer: Unfortunately, the Majestic system you refer to is too tall to safely fit in this surround. From Page: CUI-EMBC1S [1] Manufacturer's Product Number: EMBC-1S-UO Our SKU: EMBC-1S-UO Page ID: cui-embc1suo Links: ------ [1] http://w...
Our Answer: 10 in. to 14 in. hardwood logs are recommended. The burn time will depend upon the draft damper adjustment and spin draft control. The more closed the spin draft is set, the lower and slower the fire will burn. The more open, the faster a...
Our Answer: Like all doors by Portland Willamette, this door features tempered glass that is 3/16" thick. From Page: FSD-9100-3621-09 [1] Manufacturer's Product Number: 9100-3621-09 Our SKU: 9100-3621-09 Page ID: fsd-9100-3621-09 Links: ---...
Our Answer: This product is made for the California Outdoor Concepts fire pits only so we could not guarantee you that this would work for your setup. From Page: COC-902 [1] Manufacturer's Product Number: 902 Our SKU: 902 Page ID: ststicebuac...
Our Answer: Per Monessen's tech department, the right blower for you is the BLOT unit. Please follow the below link to view it. Majestic BLOT Variable Thermostat Forced Air Fireplace Blower [1] From Page: MAJ-BLO24T [2] Manufacturer's Product Num...
Our Answer: Being a natural vent insert, this model will not have any glass. It instead utilizes a pull screen to cover the opening. Since it draws combustion air from the room, glass would inhibit the operation of the appliance. If you are intereste...
Our Answer: No. You may not mix brands of chimney pipe. However, we do carry a full line of Simpson Duravent products. From Page: CPF-676-STEMP [1] Manufacturer's Product Number: 6L8+ Our SKU: 6L8+ Page ID: cpf-676-stemp Links: ------ [1] h...
Our Answer: Our CPF-61206 by Woodfield offers wrought iron construction. From Page: CPF-61206 [1] Manufacturer's Product Number: 61206 Our SKU: 61206 Page ID: cpf-61206 Links: ------ [1] http://www.efireplacestore.com/cpf-61206.html
Our Answer: The price on this fireplace does not include any pipe that would be needed to vent the unit. This fireplace uses FMI 8" inner diameter pipe only, an example of which can be found at this link: FMI Wood Fireplace 8-in. Diameter Chimney Ven...
Our Answer: The new stoves are indeed completely air tight and have only a small inlet for combustion air that does not allow smoke to back puff. If the stove's chimney system is set up properly, you should not have any issues with smoke at all. Howe...
Our Answer: No, it would not. This item is designed to adapt a cast iron surround to a Napoleon NZ-26 fireplace. Your best bet might be one of our wood-burning inserts, if your current application can accept one. From Page: NPL-AK-5 [1] Manufactu...
Our Answer: In a word, no. Woodburning inserts are specially designed to not use a grate. The firebox of woodburning inserts are far and wide too small to allow a grate to fit. More importantly, inserts themselves are made to be highly efficient appl...
Our Answer: I sharp knife or pair of cutters will be fine to cut this item to length. The squarer you can make the cut, the better the seal will be. Before installing the gasket, it will be necessary to seal the cut ends by applying a liberal amount ...
Our Answer: The difference is in the functionality of the remote. While both feature variable flame control, only the deluxe offers a room temperature feature and thermostatic control. From Page: PTS-CHASG10-30-15P [1] Manufacturer's Product Num...
Our Answer: This product is graphite impregnated, so it will have the graphite powder forced into the entire width of the gasket. From Page: FSD-154 [1] Manufacturer's Product Number: 154 Our SKU: 154 Page ID: fsd-154 Links: ------ [1] http:...
Our Answer: Unfortunately, not. No blower is available for this unit. From Page: FSD-ANT-C [1] Manufacturer's Product Number: ANT-C Our SKU: ANT-C Page ID: fsd-ant-c Links: ------ [1] http://www.efireplacestore.com/fsd-ant-c.html
Our Answer: The high quality steel of our SOJ-32SM will accept paint just fine. Please keep in mind that you will need to use a paint specifically designed for high temp applications. We have a few to choose from. Please find the below option. Thurma...
Our Answer: This product can indeed be used to parge smoke chamber and firebox walls, however it is meant to be applied to a fairly uniform surface. Any cracks bigger than 1/8" can be difficult to bridge. It is recommended to fill any large cracks wi...
Our Answer: Unfortunately, no. The closest size we have to that is a 17" x 49" in this model. From Page: HYC-BBT1753KD [1] Manufacturer's Product Number: BBT1753K Our SKU: BBT1753K Page ID: hyc-bbt1753kd Links: ------ [1] http://www.efirepl...
Our Answer: Please download the product manual on this page for complete instructions for operating this remote. If you can not get your answer from the manual, I would recommend calling Ambient technical support at 800-398-6195. From Page: CUI-RCS...
Our Answer: This item is manufactured to be used with Napoleon fireplaces. However, its design allows it to be used with any blower or air distribution kit. It will work just fine in your application. From Page: NPL-GD36 [1] Manufacturer's Produ...
Our Answer: While it is possible to use a vent-free log set in a vented firebox, there is no way to convert a vent free appliance to be vented. From Page: FSD-PCBM-42 [1] Manufacturer's Product Number: PCBM-42 Our SKU: PCBM-42 Page ID: fsd-p...
Our Answer: Unfortunately, the remote itself cannot control function of the burner, without the correct pilot kit. A remote ready on/off or variable flame pilot assembly must be attached to the G10 burner, in order for you to be able to utilize a rem...
Our Answer: These installations are pretty straight forward. Please follow the below link to view one of our vent kit options. Empire DVVK4REVS Horizontal Direct Vent Kit for Homes with Vinyl Siding [1] From Page: CUI-DVCD32FP50N [2] Manufacturer...
Our Answer: Are you interested in simply installing a gas log set or would you prefer a full direct vent insert? If you're simply interested in a gas log set, there is no need to alter the venting to your fireplace. Unless, of course, there is a prob...
Our Answer: The comprehensive warranty on this product is 1 year from date of installation, although U.S. Stove has made past exceptions on warranty coverage, depending on individual circumstances. They will not honor the warranty if improper fuel ha...
Our Answer: This mirror extends to 27". From Page: CPF-64050 [1] Manufacturer's Product Number: K-2L Our SKU: K-2L Page ID: cpf-64050 Links: ------ [1] http://www.efireplacestore.com/cpf-64050.html
Our Answer: This kit will include 3 upper louvers and 4 bottom louvers. They measure approximately 40" across. These louvers are designed specifically to be used with certain models of Empire fireplace and we cannot guarantee fitment on other manufac...
Our Answer: All of our smaller Empire gas heaters feature vent free operation. From Page: CUI-BF30NAT [1] Manufacturer's Product Number: BF-30NAT Our SKU: BF-30NAT Page ID: cui-bf30nat Links: ------ [1] http://www.efireplacestore.com/cui-bf...
Our Answer: These doors are specifically designed to mount to an FMI Bungalow fireplace. This door features locating tabs/pins that snap right into the Bungalow's firebox surround. From Page: FSD-BDB36 [1] Manufacturer's Product Number: BDB36 ...
Our Answer: A masonry saw would be most appropriate for cutting these refractory panels. From Page: CPF-42428 [1] Manufacturer's Product Number: 42428 Our SKU: 42428 Page ID: cpf-42428 Links: ------ [1] http://www.efireplacestore.com/cpf-42...
Our Answer: Per this unit's BTU rating, it should effectively heat approximately 1,400 square feet. From Page: CUI-RH50CLP [1] Manufacturer's Product Number: RH-50CLP Our SKU: RH-50CLP Page ID: cui-rh50clp Links: ------ [1] http://www.efire...
Our Answer: This model of stove will heat an area of up to 2,000 square feet. This measurement is attained by the manufacturer in a test environment with 8 foot ceilings and at high burn. Smaller fires and higher ceilings will result in less heating ...
Our Answer: The back width measures approximately 23.5" and the front width is 19". It is about 15" deep. From Page: UF-C-1533 [1] Manufacturer's Product Number: C-1533 Our SKU: C-1533 Page ID: fsd-c-1533 Links: ------ [1] http://www.efirep...
Our Answer: No, this is a vented appliance. From Page: FSD-B-401-107-NA [1] Manufacturer's Product Number: B-401-107-NA Our SKU: B-401-107-NA Page ID: fsd-b-401-107-na Links: ------ [1] http://www.efireplacestore.com/fsd-b-401-107-na.html
Our Answer: The approximate weight of this set is 16 lbs. From Page: FSD-18023 [1] Manufacturer's Product Number: 18023 Our SKU: 18023 Page ID: fsd-18023 Links: ------ [1] http://www.efireplacestore.com/fsd-18023.html
Our Answer: The depth of this unit is approximately 15 1/4" deep. From Page: UF-C-1534 [1] Manufacturer's Product Number: C-1534 Our SKU: C-1534 Page ID: fsd-c-1534 Links: ------ [1] http://www.efireplacestore.com/fsd-c-1534.html
Our Answer: It would not be recommended to install this fireplace on a screened-in patio or porch. This unit is not made to be used outdoors, and even though it would be sheltered, there would still be condensation from the outside atmosphere that wo...
Our Answer: This unit is only offered in either an unfinished exterior or a Fruitwood finish. It is not available in those dimensions. From Page: PRM-134 [1] Manufacturer's Product Number: 134-48 Our SKU: 134-48 Page ID: prm-134 Links: ----...
Our Answer: There is just one set of doors that can be used with this fireplace. However, the set is available in three finishes: black, brushed brass, and platinum. Please view them via the following links. FMI 36 Inch Outdoor Bi-Fold Glass Door - B...
Our Answer: These screens offer standard 1/4" mesh. From Page: CPF-61086 [1] Manufacturer's Product Number: 61086 Our SKU: 61086 Page ID: cpf-61086 Links: ------ [1] http://www.efireplacestore.com/cpf-61086.html
Our Answer: This blower is specifically designed for FMI fireplaces. Further, it appears that Regency makes blowers specific for their inserts, as well. From Page: FSD-BK [1] Manufacturer's Product Number: BK Our SKU: BK Page ID: fsd-bk Lin...
Our Answer: Circulating fireplaces pull in cool room air, heat it, and return it to the room - either passively or with the assistance of a blower kit. Non-circulating units do not offer this feature but they do provide a more modern look. From Pa...
Our Answer: This mantel is not meant to be used in a way that you have described. It is a flush profile mantel meant to go up against a combustible wall in which a fireplace is framed. From Page: CUI-MFL52PG [1] Manufacturer's Product Number: MF...
Our Answer: It appears you have a fireplace that has glass doors, which would make a track mount type of hood unusable. It would be necessary for you to utilize this type of hood: Elite Glass Enclosure Fireplace Hood with Surface Mount - 36 Inch x 4 ...
Our Answer: The DFS36PVC comes standard without the brick liner. You are free to choose between Cottage Clay or Cottage Red liners. We can special order the Cottage Clay line, if you'd prefer it. Please follow this link to view the Cottage Red liner....
Our Answer: Yes. In fact, that is its prime objective. It is part of the Selkirk DSP Double-Wall line. From Page: CPF-7755-DSPMADAPT [1] Manufacturer's Product Number: 7755-DSPMADAPT Our SKU: 7755-DSPMADAPT Page ID: cpf-7755-dspmadapt Links...
Our Answer: At this time, we do not carry a product that has a full three sides. We do carry a few models of decorative gas log surrounds that have two short sides that are used to stand the surround in the back of the fireplace, but not a model with...
Our Answer: No. This liner is made for 24" Empire Vail Fireplace only. We do have generic fireplace refractory panels that may work for you. Please see the links below for details: Hargrove Replacement Fireplace Refractory Panel - 24 inch X 28 inch [...
Our Answer: Absolutely, it can. The only thing that you have to add is the vent free burner and log set. Please follow the below link to view our available options. Be sure to take advantage of the "Narrow Selection By" column on the left of the page...
Our Answer: According to Monessen, the cinders offer a red glow when installed on the ember burner of a compatible Monessen fireplace. They are purely for visual appeal when the unit is burning and do not offer any additional heat. The ceramic granul...
Our Answer: Our CUI-CIFPB1C measures 42 7/16 x 42 7/16 x 7/8 and the stone inlay simply fits inside of it. From Page: CUI-CIFPB1C [1] Manufacturer's Product Number: CIFPB-1C Our SKU: CIFPB-1C Page ID: cui-cifpb1c Links: ------ [1] http://www...
Our Answer: This damper plate would be the closest match for your application but it may not be perfect. It all depends on whether you have the room in the damper throat for a plate that is 2 inches wider than your existing one. You then have to cons...
Our Answer: This unit will hold one-third face cord of firewood. From Page: FSD-18565 [1] Manufacturer's Product Number: 18565 Our SKU: 18565 Page ID: fsd-18565 Links: ------ [1] http://www.efireplacestore.com/fsd-18565.html
Our Answer: These ES-233000 heaters work great and only require a 36" clearance to combustible materials from the top of the dome. Only a 24" clearance to combustible materials is needed from the side of the dome. However, per your deck's roof dimens...
Our Answer: This fireplace weighs 57 lbs. It will arrive mostly assembled, with the exception of the burner, which will be a simple "drop-in" assembly. The Bio Flame factory is located in Calgary, Alberta, Canada. From Page: FSD-ROG-FT-WH [1] Ma...
Our Answer: This unit requires a fireplace with dimensions at least 27.5" wide, 14" deep, and 22" tall. It can accept logs up to 16" long. From Page: FSD-OB01151 [1] Manufacturer's Product Number: OB01151 Our SKU: OB01151 Page ID: fsd-ob0115...
Our Answer: Please download Product Manual #2 on this item page. This is Napoleon's brochure for their stoves and inserts. The Majolica Brown Cast Iron Surround is shown on page 22. However, to get a better idea of the finish check out the stove fini...
Our Answer: This brush does indeed feature rather stiff bristles that are designed to withstand the use and abuse of daily cleanings. It is sized appropriately for your 11" flue and should work well for this application. Please note that it is design...
Our Answer: This stove does not have a designated cook top as some stoves do. But, its top surface will get plenty warm enough to cook on. From Page: NPL-2100 [1] Manufacturer's Product Number: 2100 Our SKU: 2100 Page ID: npl-2100 Links: --...
Our Answer: We actually have two blowers available for our NPL-GVF36. The NPL-GZ550-1KT and the NPL-B440-KT. You may view them at the following links. Napoleon Blower Kit with Variable Speed and Thermostatic Control [1] Napoleon Zero Clearance Econom...
Our Answer: This unit does indeed open fully when the handle is released. From Page: CPF-12130 [1] Manufacturer's Product Number: 12130 Our SKU: 12130 Page ID: cpf-12130 Links: ------ [1] http://www.efireplacestore.com/cpf-12130.html
Our Answer: Generally, no mortar is required to seal these panels. You would simply cut them to overlap as they are installed. From Page: CPF-42428 [1] Manufacturer's Product Number: 42428 Our SKU: 42428 Page ID: cpf-42428 Links: ------ [1]...
Our Answer: It is recommended that you use FMI pipe for this item. Please follow the below link for an example. FMI Wood Fireplace 8-in. Diameter Chimney Venting Pipe for FMI Woodburning Fireplaces - 48-in. Length [1] From Page: CUI-VB42LI1 [2] M...
Our Answer: Unfortunately, this is a non-circulating fireplace without louvres. As such, it does not offer the ability to add a blower, which uses a circulating system to operate. From Page: CUI-VB361 [1] Manufacturer's Product Number: VB361 O...
Our Answer: An insert can be installed into a prefab fireplace. However, it may be difficult to find an insert that fits. Many pre-fab fireplaces are a bit small. Please view our line of inserts by following the below link. Wood Burning Fireplace Ins...
Our Answer: For the money, you'll be able to get a wood stove that is capable of producing about twice as many BTUs as a gas burner. Also, wood is our only renewable energy resource. You will not have a monthly bill if you install a wood stove but th...
Our Answer: Unfortunately, this unit would not comply with Washington standards. Any unit to be installed in Washington state would need to carry an EPA certification. All units listed on our site that are EPA approved will indicate this in the title...
Our Answer: Unfortunately, the liner kit you inquired about is only made to work with the FMI Cape Cod firebox. That firebox is a gas vent-free unit, so it would not be recommended for you to try to use it in your woodburning fireplace. We do, howeve...
Our Answer: Based on those model numbers provided, the BLOTCS would indeed be the correct blower to fit those models. However, while the unit does look almost identical to those models, I cannot guarantee that the blower would be an exact fit, since ...
Our Answer: Unfortunately, the dimensions on the Pearl Mantels cannot be altered in any way. We have had customers make similar inquiries previously, and the manufacturer has told us it is not something they can accommodate. I apologize for this inco...
Our Answer: Indeed it can. The unit comes standard with a millivolt valve, meaning that it has a standing pilot and generates it's own power for the gas valve to operate. If you opt for the Signature Command controls, you will have a 115 volt module ...
Our Answer: Previously, Duravent sold this cap with the spark arrestor screen installed, but they have since stopped doing so. The following item can be modified and installed onto all manufactured chimney caps. SuperPro All-Fuel Chimney Stainless St...
Our Answer: No, this is an electric stove, so a blower would have no functionality with it. From Page: FRS-60351 [1] Manufacturer's Product Number: 60351 Our SKU: 60351 Page ID: frs-60351 Links: ------ [1] http://www.efireplacestore.com/frs...
Our Answer: Unfortunately, no. This door frame is only for use with 36" Tahoe Deluxe and 34" Keystone Deluxe fireplaces. You may want to look at our other fireplace doors, which you can see at this link: Fireplace Doors [1] From Page: CUI-DVW2 [2] ...
Our Answer: You would use these 30-degree elbows on a chimney run that is obstructed in some way from a straight vertical run. For example, if you have to go around a rafter or some other obstruction. It is always best to vent 100% straight verticall...
Our Answer: According to FMI, this blower measures 17 3/4" long, 5" tall, and 2" deep. The individual fans measure about 3 3/4" across. This fan is only recommended for use with compatible FMI or Vantage Hearth units, as it may not generate proper ai...
Our Answer: The guidelines for insulating a liner are based on the size and location of the flue. If the area of the flue is more than twice the liner, you will need to insulate. Also, if the chimney is on an exterior wall, insulation is strongly rec...
Our Answer: It does. it sits flat against the ceiling, around the perimeter of the ceiling support. From Page: CPF-70752 [1] Manufacturer's Product Number: 9545TR Our SKU: 9545TR Page ID: cpf-70752 Links: ------ [1] http://www.efireplacesto...
Our Answer: Installation of this sensor will vary for different blower units, but the sensor will come with installation instructions that cover proper mounting for your specific blower. Most sensors merely require you to mount the sensor to the insi...
Our Answer: We do have another version of this cap, if you are not in California and do not require the mesh size on this particular cap. Please see another 10" HomeSaver Pro cap here: HomeSaver Pro 10 Inch Round Chimney Cap for Solid Pack Factory-Bu...
Our Answer: The insert measures 36.88"w x 15.38"d x 7.25"h and is capable of 4,600 BTU. This heater can comfortably heat a 130 square foot room. It features a thermostat, an automatic shut off and a remote control. From Page: FSD-23MM3104EPVP-SO [...
Our Answer: The bristles on the FSD-1604 AW Perkins 4 Inch Pellet Vent Spin Brush are made of nylon. From Page: FSD-1604 [1] Manufacturer's Product Number: 1604 Our SKU: 1604 Page ID: fsd-1604 Links: ------ [1] http://www.efireplacestore.com...
Our Answer: This is indeed the proper blower assembly for use with both the BGD and GD36NTR. From Page: NPL-GZ550-1KT [1] Manufacturer's Product Number: GZ550-1KT Our SKU: GZ550-1KT Page ID: npl-gz550-1kt Links: ------ [1] http://www.efirepl...
Our Answer: Being that this is an elbow for a chimney liner installation, neither of the ends will be crimped. The ends are only slightly over 7 inches, so that the liner will be able to slip over each end, then band clamp into place. You can also us...
Our Answer: These louvers are specifically designed for the 48" Tahoe fireplaces. They measure 46" wide and approximately 3 1/2" tall. From Page: CUI-DVG4A [1] Manufacturer's Product Number: DVG-4-ABL Our SKU: DVG-4-ABL Page ID: cui-dvg4ahp ...
Our Answer: Most storm collars will leave a small gap at the leading edge where they meet the pipe. It will be necessary to seal that gap with roofing mastic or an exterior roofing sealant. It is also a good idea to seal the overlap on the collar its...
Our Answer: The general rule for increasing stove-pipe diameter is "yes, if it's old". Older model wood stoves were not manufactured to the strict efficiency standards that new stoves are today. So, older stoves send a lot of heat up through their fl...
Our Answer: Unfortunately, this stove is only made with the flue collar on the top. From Page: SBI-DB03030 [1] Manufacturer's Product Number: DB03030 Our SKU: DB03030 Page ID: sbi-db03030 Links: ------ [1] http://www.efireplacestore.com/sbi-...
Our Answer: This unit's physical dimensions are 41" wide by 34 1/2" tall by 18" deep. It requires minimum rough opening dimensions of 41 1/4" wide by 35" tall by 17 1/2" deep. From Page: CUI-DFS36NVC [1] Manufacturer's Product Number: DFS36NVC ...
Our Answer: Unfortunately, each pipe manufacturer is different. While they all offer similar diameters of pipe, they also feature proprietary locking tabs on their ends. We do not recommend mixing brands of pipe, simply because they will not lock tog...
Our Answer: We would recommend that you confirm the outer diameter of your pipe. Better still would be the positive identification of the brand of pipe that you have. This item is designed to work with pipes that feature a 10" outer diameter. From...
Our Answer: We only offer one paint with brush-on application. Unfortunately, it is black. Please follow the below link to check it out. AW Perkins 1400 Degree Brush-on Black Stove and Grill Paint - Brush On [1] From Page: CPF-43406 [2] Manufactu...
Our Answer: This unit can indeed be hung on a wall beneath a TV. You'll want to maintain a clearance of 18" between the top of the fireplace and the bottom of the TV. From Page: NPL-WMFE3 [1] Manufacturer's Product Number: WMFE3K Our SKU: WMFE...
Our Answer: This pipe features a 5" inner diameter and 8" outer diameter. Most direct vent appliances with this configuration do not require an adaptor. However, some do. I do not have any literature on the Kozy Heat units. I would recommend confirmi...
Our Answer: This stove would need to sit 15" away from a back wall. You can see this and more clearance information in the owner's manual, which is located on this item page. See page 3 for the clearance information. From Page: MAJ-WR244 [1] Manu...
Our Answer: While this thermostat is designed to modulate a hot air distribution kit, it will also work for your application. The mechanics of the thermostat will be exactly the same as a thermostat you would purchase specifically for this heater. ...
Our Answer: Unfortunately, the Timberwolf 2100 stove does not allow for any kind of fresh air kit. We do offer a similar stove by a different manufacturer that does, however: Majestic Windsor Mobile Home-Approved High-Efficiency Wood Burning Stove [1...
Our Answer: This stove features a primary air control handle that is located between the stove door and the ash pan. From Page: USS-2500 [1] Manufacturer's Product Number: 2500 Our SKU: 2500 Page ID: uss-2500 Links: ------ [1] http://www.efi...
Our Answer: Yes, this extension is just a miniature version of the surround. They simply stack together. You would secure them both to a 2x4 framework. From Page: CPF-44317 [1] Manufacturer's Product Number: 44317 Our SKU: 44317 Page ID: cpf...
Our Answer: The fuel consumption will vary widely depending on the quality of wood and coal used, your fire tending skills, and the effectiveness of your chimney system. On average, the manufacturer indicates this furnace can consume 120-180 pounds o...
Our Answer: This unit will attach to your flue however it will not be a snug fit on the 8" side. A better option might be the below cap. It will mount via swing tabs to the top of your crown. BigTop 14 in. x 21 in. Copper Multi-Flue Chimney Cover [1]...
Our Answer: Yes, they do. Please go to the link below for the black version of this fireplace door: FMI Extruded Aluminum Bi-Fold Glass Doors for 42 Inch Mission Gas Fireplace - Black [1] From Page: FSD-BD42B [2] Manufacturer's Product Number: BD...
Our Answer: See the link below for the white mantel for the Vail 26 inch fireplace: Empire EMBC11S Corner Wooden Mantel Cabinet with Base - For 26 Inch Vail Fireplaces [1] The white mantel linked above and the Vail 26 inch fireplace can be purchased ...
Our Answer: The Elite Square End Fireplace Hood with Lintel Mount is designed to be mounted to the lintel of your fireplace - the horizontal support across the top of your fireplace. The Elite Glass Enclosure Fireplace Hood with Surface Mount attache...
Our Answer: Due to the design of the Napoleon Arlington, it is doubtful that the stove chassis would become hot enough to allow humidification to occur. The stove is insulated along the top and as a result, does not get as hot as an equivalent wood b...
Our Answer: No, this unit must hang on the wall and sit proud of it. It should not take up too much room. In fact, the actual firebox is only about 6" deep From Page: NPL-WMFE3 [1] Manufacturer's Product Number: WMFE3K Our SKU: WMFE3K Page ID...
Our Answer: This sealant is black. From Page: RUT-641 [1] Manufacturer's Product Number: 641 Our SKU: 641 Page ID: rut-641 Links: ------ [1] http://www.efireplacestore.com/rut-641.html
Our Answer: Unfortunately, we only have two options for the vent free baskets. Please follow these links to see our options: Victorian Hearth Vent-Free Natural Gas Burner with Realistic Coals - 13 Inch [1] Victorian Hearth Vent-Free Natural Gas Burne...
Our Answer: It is best to match your brush to the shape of your flue pipe. If your pipe is round, go with this one. From Page: RUT-16906 [1] Manufacturer's Product Number: 16906 Our SKU: 16906 Page ID: rut-16906 Links: ------ [1] http://www...
Our Answer: Unfortunately, there is currently no corner cabinet available for the MAJ-LCUF36C-R firebox. Only standard wall cabinets are available for the Lo-Rider unit. From Page: MAJ-LCUF36C-R [1] Manufacturer's Product Number: LCUF36C-R Our...
Our Answer: Yes, sir, this kit includes two mesh panels, the 1/2" attachment rings and coil pulls. From Page: FSD-RMP2422 [1] Manufacturer's Product Number: RMP2422 Our SKU: RMP2422 Page ID: fsd-rmp2422 Links: ------ [1] http://www.efireplac...
Our Answer: The flames on this unit will not touch the logs. This is to ensure complete combustion and prevent problems with carbon monoxide and soot. While some vent-free appliances may have minimal contract with flames and logs, the vast majority a...
Our Answer: Please note that this item is a glass enclosure designed to be installed on a masonry fireplace. This item is not a fireplace. From Page: FSD-P3530-BI [1] Manufacturer's Product Number: P3530-BI Our SKU: P3530-BI Page ID: fsd-p35...
Our Answer: This screen kit is specially designed for use with Napoleon's GDI44 fireplace. If this is your fireplace and you have a DK44 door kit, they will work perfectly. From Page: NPL-SK44-A [1] Manufacturer's Product Number: SK44-A Our SK...
Our Answer: A blower is not offered for this fireplace. From Page: FSD-ALTC-C [1] Manufacturer's Product Number: ALTC-C Our SKU: ALTC-C Page ID: fsd-altc-c Links: ------ [1] http://www.efireplacestore.com/fsd-altc-c.html
Our Answer: One of our adjustable surface mount hoods should work just fine for you. Please follow the below link to check it out. Elite Adjustable 4 Inch Fireplace Hood with Surface Mount [1] From Page: CUI-VB2H42 [2] Manufacturer's Product Numb...
Our Answer: This fireback will work just fine to protect the liner walls of your fireplace. The manufacturer, Peterson, also produces gas log sets. They made this fireback with gas log appliances in mind. In Response to Question: I have a wood b...
Our Answer: This unit does not come with a remote or a remote ready pilot kit. The following unit is almost identical to this unit but does come with a remote ready pilot kit: Vail Premium Vent-Free Propane Fireplace with Remote Ready Controls - 36 I...
Our Answer: We unfortunately do not have this exact kit in a nickel finish. However, please follow the below link to view one of our sets that is nickel. Woodfield Satin Nickel 4 Piece Fireplace Tool Set [1] From Page: UF-T51040AB [2] Manufacture...
Our Answer: By design, vent free appliances consume oxygen from the room/home in which they are installed. In fact, after extended periods of use it is recommended to crack a window to replenish available oxygen in the room. For your particular appli...
Our Answer: Despite the patio, this firebox will still rust and corrode over time due to the moisture in the air. For a firebox that will be suitable for use in your situation, please see the following: Tuscan 42 in. Outdoor Wood Burning Firebox in N...
Our Answer: The N indicates that the unit is currently configured to operate on natural gas. The propane version would have a part number of DVBLPSC7. I would say they simply left the N out of the part number by accident or they may convert the unit ...
Our Answer: These panels are for a gas fireplace, specifically the Empire Vail 32" fireplace. Please see our universal woodburning panels here: Hargrove Replacement Fireplace Refractory Panel - 24 inch X 28 inch [1] Hargrove Replacement Fireplace Ref...
Our Answer: This particular door set is designed to work with the Vantage Hearth Value Line series of fireplace. The doors will have an overall height of 21" and will have tabs on each corner to pop the assembly into the face of the fireplace. From...
Our Answer: This log lighter attaches to a pipe with standard 1/2" NPT. From Page: PTS-LC-1 [1] Manufacturer's Product Number: LC-1 Our SKU: LC-1 Page ID: pts-lc-1 Links: ------ [1] http://www.efireplacestore.com/pts-lc-1.html
Our Answer: You can find the owner's manual on the item page itself, it is a downloadable PDF file. From the "Troubleshooting" section: 1. Replace batteries. Change batteries every 6 months. 2. Check battery installation and replace batteries. 3. Pre...
Our Answer: Your pilot kit is likely beeping due to low batteries. Your hand-held transmitter should take one 12 volt battery and the receiver in the fireplace will take 4 AA batteries. We recommend replacing the batteries in the hand-held transmitte...
Our Answer: We will be happy to assist you. For a complete detailed quote, please complete this form: Chimney Pipe Design & Quote Form [1] This will help us provide the most accurate and cost effective quote we can. If you have questions, please call...
Our Answer: This panel measures approximately 22 1/8" wide by 22 1/4" tall. It is specifically designed to be used in a Monessen B-Vent gas fireplace. From Page: CUI-DBVFBS [1] Manufacturer's Product Number: DBVFBS Our SKU: DBVFBS Page ID: c...
Our Answer: While you can use either solid or flex venting on this insert, it is most common to use a solid tee on the back of the appliance, then convert to a flexible liner for the remainder of the run. Due to the construction of most chimneys, it ...
Our Answer: While we do have other tool sets that come in those finishes, this brush and shovel set are currently only available in the black iron finish that is shown. From Page: NPL-TS12 [1] Manufacturer's Product Number: TS12 Our SKU: TS12 ...
Our Answer: Household Manufacturing is the old name for Metal-Fab. This product is slightly different from Duravent products. We do carry the Metal-Fab products and they can be seen in this section: B Vent Chimney Pipe [1] You will need to use the se...
Our Answer: Yes, sir! Our HomeSaver UltraPro is certified for wood, pellet, oil, and coal. From Page: CPF-17528 [1] Manufacturer's Product Number: 17528 Our SKU: 17528 Page ID: cpf-17528 Links: ------ [1] http://www.efireplacestore.com/cpf-1...
Our Answer: Unfortunately, the price on the Napoleon GVF36 fireplace does not include that mantel in the picture. That mantel is available, and you can see it and other Napoleon mantels that can be used with this fireplace at the following link: Wood...
Our Answer: Yes, these Fireplace Ring Swirl Black Andirons are indeed made of cast iron. From Page: UF-A1124 [1] Manufacturer's Product Number: A-1124 Our SKU: A-1124 Page ID: firiswblan Links: ------ [1] http://www.efireplacestore.com/firis...
Our Answer: The deluxe remote (PTS-VR-2A) features variable flame height control but also offers thermostatic functionality. It will vary the flame height of your log set per the temperature you set. From Page: PTS-APK-17P [1] Manufacturer's Pro...
Our Answer: Vent free fireplaces are indeed legal to use in a bedroom, as long as the BTU rating does not exceed 10,000. Given the square footage of the room, this would only provide some supplemental heat. For better heating of the room, you may wan...
Our Answer: This unit does not include a remote control as standard. From Page: FSD-PCSD25T [1] Manufacturer's Product Number: PCSD25T Our SKU: PCSD25T Page ID: fsd-pcsd25t Links: ------ [1] http://www.efireplacestore.com/fsd-pcsd25t.html
Our Answer: This is indeed the closest match we would have to your application. It should work fine as long as you have a few inches on either side of the damper throat to accommodate the overhang. From Page: CPF-26260 [1] Manufacturer's Product...
Our Answer: Unfortunately, we do not provide any service or repairs. However, Drolet's website has a promising installer locator tool. In Response to Question: I have a Drolet eco 45. H1 appears meaning the automatic high temp switch was tripped...
Our Answer: The closest damper plate to your measurements would be this product: Vestal Cast Iron Fireplace Damper Plate - For 36 Inch Dampers [1] It measures 28 3/8" by 7". Unfortunately, we only carry damper plates manufactured by Vestal, so we do ...
Our Answer: The overall height of this surround is 38" The width across the front at the top is 46". Width across the front at the base is 36". The depth from the center of the mantel to the back corner is 26 3/4". The length from either the left or ...
Our Answer: Only the item marked as 'A" is included. The finishes of Glavalume DuraTech and DuraPlus will match. However, if you currently are using DuraTech chimney pipe, we recommend that you continue using it. DuraPlus and DuraTech will not twist-...
Our Answer: Unfortunately, we do not currently carry brick surrounds. The item offered on this page is just the firebox and interior brick liner. From Page: CUI-MCUF42D-R [1] Manufacturer's Product Number: MCUF42D-R Our SKU: MCUF42D-R Page I...
Our Answer: Unfortunately, not. This fireplace can only be fueled by Natural Gas or Propane. We do not currently carry any Butane fueled appliances. From Page: CUI-BVD34FP30FN [1] Manufacturer's Product Number: BVD-34-FP30FNN Our SKU: BVD-34-FP...
Our Answer: This is a great option - as direct vent units generally are. Direct vent run efficiently without ever pulling combustion air from a room. Our general rule is 35 BTUs per square foot of desired heated space. For your application, the below...
Our Answer: These magnetic thermometers are designed for single-wall stove pipe only. From Page: CPF-41100 [1] Manufacturer's Product Number: 41337 Our SKU: 41337 Page ID: cpf-41100 Links: ------ [1] http://www.efireplacestore.com/cpf-41100...
Our Answer: To make sure you get a blower that will work with your fireplace, we will need the manufacturer and model number of your unit. With this information, we can determine if we have a blower that will work for your fireplace. From Page: CU...
Our Answer: Unfortunately, these trim kits are indeed designed to be used explicitly with Napoleon fireplaces. From Page: NPL-TB636 [1] Manufacturer's Product Number: TB636K Our SKU: TB636K Page ID: npl-tb636 Links: ------ [1] http://www.efi...
Our Answer: The ability to swap your remote all depends on the functionality of your appliance. The TLM only offers on/off control. It is designed to be used with any millivolt valve system that has on/off control options. The TSFSC is designed to be...
Our Answer: This is perfectly acceptable to be used in that fashion. This box can be either framed around or enclosed in a wooden mantel surround, just as long as the heat standoffs on the box are not altered in any way. You must also take care to ob...
Our Answer: Yes, this same mantel is available unfinished. Please see this link: Vantage Hearth 32 Inch Unfinished Traditional Wooden Corner Mantel [1] From Page: CUI-C32CO [2] Manufacturer's Product Number: C32CO Our SKU: C32CO Page ID: cui-...
Our Answer: This elbow is approved for use with gas appliances only. If you are converting a horizontal run to a vertical run, you may want to consider a Tee with cap. Please follow the below link to our PelletVent Pro pipe. Dura-Vent PelletVent Pro ...
Our Answer: All of our Minuteman firebacks are about 1" thick. From Page: ADC-670500 [1] Manufacturer's Product Number: X670500 Our SKU: X670500 Page ID: adc-670500 Links: ------ [1] http://www.efireplacestore.com/adc-670500.html
Our Answer: All of our valve keys fit 1/4-5/16 sized valves. Measure the opening on your current valve keys to confirm this is the size you need. From Page: CPF-47128 [1] Manufacturer's Product Number: NKY.8.BR Our SKU: NKY.8.BR Page ID: cpf-...
Our Answer: This unit must be mounted on the wall. It cannot be recessed into a wall. It comes with the necessary hardware for hanging. From Page: NPL-WMFE1 [1] Manufacturer's Product Number: WMFE1K Our SKU: WMFE1K Page ID: npl-wmfe1 Links:...
Our Answer: This mantel does not require the separate purchase of a surround of any sort. However, you will want to make sure that both the interior and exterior dimensions work for you. From Page: CUI-MFL52PG [1] Manufacturer's Product Number: ...
Our Answer: These stoves are manufactured in China in a factory owned by Napoleon and staffed with Napoleon fabricators. All stoves are made to Napoleon's specs. This stove is made of steel. From Page: NPL-2200 [1] Manufacturer's Product Number: ...
Our Answer: In a word, yes. Our CPF-235 floppy brushes would work for cleaning wood burning appliance chimneys. Their non-abrasive texture makes them a great option. From Page: CPF-235 [1] Manufacturer's Product Number: PF-8 Our SKU: PF-8 Pag...
Our Answer: Those three wires are indeed for power. Hardwiring 12/2 from these wires to a power supply is a fine repair. In Response to Question: i have this furnace (Empire wall furnace model dv55ip) and it had a power cord that i cant seem to ...
Our Answer: This item mounts to the lintel of your fireplace. The lintel is the horizontal support that runs across the top of the fireplace opening. You may be more interested in a surface mount hood. Surface mount hoods attach directly to the face ...
Our Answer: These doors do not feature a gasket or seal around the door opening so they are not air tight. However, since they are cast aluminum they'd be ideal for outdoor use. From Page: CPF-09704 [1] Manufacturer's Product Number: 9704 Our ...
Our Answer: Please download the manual on the item page for complete installation instructions. From Page: CUI-RH65CBLP [1] Manufacturer's Product Number: RH-65CBLP Our SKU: RH-65CBLP Page ID: cui-rh65cblp Links: ------ [1] http://www.efirep...
Our Answer: These dampers work so well at sealing your flue that the downside to them is that they allow any odors from your chimney to creep back into your room. A thorough cleaning of your flue should alleviate the soot smell that you are noticing....
Our Answer: This is actually a fireplace insert. If you would like the dimensions of this fireplace insert, please download the manual on the product page. It has very detailed dimensions and specifications From Page: NPL-EPI-1101P-DEAL [1] Manuf...
Our Answer: We have round and square terminations that are compatible with this pipe. Please follow the below links to view these items. Round Louvered Termination for Majestic 8 in. Diameter Triple-Wall Flue Pipe [1] Square Black Louvered Terminatio...
Our Answer: You can definitely use this mantel with the 32" Vantage Hearth Logmate fireboxes, as they are designed to be compatible with one another. The Real Fyre logs that would fit properly would be 20" models. This following link is for the propa...
Our Answer: That all depends on the type of fireplace. Direct vent appliances or closed combustion chamber units, like inserts, need their glass fronts to operate correctly. On the other hand, a standard wood burning fireplace with decorative glass d...
Our Answer: A fireback can be a good way to protect against possible damage caused by cracked firebrick. Do you have a true masonry fireplace or is it a manufactured (metal) firebox? We offer refractory cement and replacement liners to repair either ...
Our Answer: Per the manual, which can be downloaded on this page, your alcove is approved for installation of this insert as long as you maintain a 12" clearance between the sides of the stove and the walls and 10" between the back of the stove and t...
Our Answer: Believe it or not, yes. The Lock-Top dampers attach to the top of your flue with silicone adhesive. Applied to a clean, dry surface the silicone will do the job to keep your damper in place. Use with your Heatalator all depends on your in...
Our Answer: Based on your dimensions, the FSD-OB02201 that you've selected would be your best choice. You may find the required accessories by clicking the "Accessories" button the insert's item page. I'd be glad to quote these for you but there are ...
Our Answer: This unit does not come with a blower but you can easily add one. Please follow the below link to view the accessory or look under the accessories tab on this item page. Majestic BLOTMC Variable Thermostat Forced Air Blower [1] From Pag...
Our Answer: A good bit of the liner requirements are dictated by the size of your masonry chimney. If the flue is not more than two times larger than the 6" vent pipe that the insert requires, you could run a short length of 6" flex liner from the in...
Our Answer: The Osburn 2400 is definitely a good choice for heating the square footage you have. SBI is the manufacturer of the Osburn line and of several other good brands such as Drolet and Flame. They are solid units that do an effective job of he...
Our Answer: These fiber panels are designed to be used only with the designated appliances. They are not universal fit and it is not recommended to trim them to size. We do have some universal fit panels available, though. Please follow the below lin...
Our Answer: This item is crimped on the 6" male end. From Page: CPF-21380 [1] Manufacturer's Product Number: 2628B Our SKU: 2628B Page ID: cpf-21380 Links: ------ [1] http://www.efireplacestore.com/cpf-21380.html
Our Answer: Because of the fact that the switch still functions like a normal timer/light switch, you can indeed use a Leviton brand timer to replace your standard wall switch. Leviton timers are even sold as accessories for certain brands of firepla...
Our Answer: Both questions you asked about this fireplace can be answered by looking at the manual, which you can download on the product page. The unit measures 23 inches tall, 19 inches across and 8 inches deep. (Dimensions can be found on page 3 o...
Our Answer: Unfortunately, this cap is a bit larger than any of the damper caps we currently offer. Please see this cap for something you may be able to make work for your application: Lock-Top 17 in. x 17 in. Energy-Saving Chimney Damper [1] The bas...
Our Answer: Yes, the this BLOT blower has a 160 cfm rating. Please note, that while it may work with your Martin unit, it is only listed here as compatible with the following: CDV Direct Vent Gas Fireplaces DVB Direct Vent Gas Fireplaces DVBH Direct ...
Our Answer: Here is some information on this item from the manufacturer's Technical Data Sheet: It is a high-quality, high-temperature flat black silicone resin paint, for interior or exterior use. Easy spray on formula contains pure silicone resin. ...
Our Answer: This cap's top lid will indeed easily come off for cleaning of your chimney pipe. From Page: CPF-13231 [1] Manufacturer's Product Number: 13231 Our SKU: 13231 Page ID: cpf-13231 Links: ------ [1] http://www.efireplacestore.com/c...
Our Answer: This model of insert can be utilized in an existing manufactured fireplace. However, the maker of the fireplace must clearly state that the unit is able to accept a wood burning insert. If the manufactured unit is not listed to accept an ...
Our Answer: The firebox will come with everything you need except perhaps a remote control which you can find on the accessories tab for this item. The white mantel can be found by following the below link. Vantage Hearth 21 Inch Traditional White Wo...
Our Answer: Unfortunately, the RCT receiver is not sold individually. However, this item does come with the remote control and the receiver together. From Page: CUI-RCT [1] Manufacturer's Product Number: RCT Our SKU: RCT Page ID: cui-rct Lin...
Our Answer: The applicator is indeed a separate item that would be an additional purchase. Please see the item's page here: ChimneySaver Cre-Away Applicator for 25 lb. Bucket [1] You will need compressed air to apply this product with that applicator...
Our Answer: The center of this unit measures approximately 8" in diameter. The base measures about 10 1/4" corner to corner. From Page: FSD-19004 [1] Manufacturer's Product Number: 19004 Our SKU: 19004 Page ID: fsd-19004 Links: ------ [1] h...
Our Answer: This paint will do the job. After the paint dries, it would probably be a good idea to run the stove on a very high temp to fully cure the paint. You'll want to be sure to burn off any fumes before using the stove to prepare a meal. Fro...
Our Answer: Our rule of thumb is 35 BTU per square foot. This unit could roughly heat a little more than 700 square feet. From Page: CUI-GWT25NAT [1] Manufacturer's Product Number: GWT-25NAT Our SKU: GWT-25NAT Page ID: cui-gwt25nat Links: -...
Our Answer: This unit can be controlled thermostatically. When ordering, select the Deluxe Variable Remote. You will get our PTS-VR-2A. This remote features variable flame height control and a thermostatic function. You simply enter the temperature y...
Our Answer: Indeed, it can. This unit will mount directly to the under side of your fireplace's lintel. From Page: FSD-ESH442 [1] Manufacturer's Product Number: ESH442 Our SKU: ESH442 Page ID: fsd-esh442 Links: ------ [1] http://www.efirepl...
Our Answer: You could use an oval to round flex reline pipe for the beginning of your vent run. This pipe features an oval end and length that will squeeze through your damper opening and attach to your insert. The other end of the pipe is round and ...
Our Answer: The LHD45 is not available as a see-through model, but the LHD50 is. Here is a link to the item page for the Napoleon LHD50 fireplace: Napoleon LHD50 Linear Series Gas Fireplace [1] Please note that you must select "2-Sided Linear Firepla...
Our Answer: The 12 in measurement is the overall length of the shutoff valve key. In Response to Question: What does the "12-in" refer to for this fireplace key, e.g., from the very far end of the base to the front part of the handle, from one ed...
Our Answer: This blower will install in the bottom of Vantage Hearth fireplaces, beneath an access panel in the floor. The blower will draw cool air through the bottom louvers on the face of the fireplace, then circulate the air around the back of th...
Our Answer: Here is the propane model of that fireplace: Empire Tahoe Luxury Direct Vent Propane Fireplace - 42 Inch [1]. From Page: CUI-DVX42FP33CLN [2] Manufacturer's Product Number: DVX-42-FP31LN Our SKU: DVX-42-FP31LN Page ID: cui-dvx42fp...
Our Answer: This item is only a firebox. It requires the installation of a ventless gas log set for completion. It is large enough to accommodate an 18" log set. Log sets of that size have a BTU range of 20,000 to 36,000 BTU. Please be aware that man...
Our Answer: The gas valves that these keys operate are normally 1/4 turn valves. Generally, the key handle is parallel to the gas line when the valve is open and perpendicular to it when the valve is closed. From Page: CPF-47129 [1] Manufacturer'...
Our Answer: These plastic covers are referred to by the manufacturer as "floor glides," and there are 4 included with this rack. From Page: ENC-LR1b [1] Manufacturer's Product Number: LR1b Our SKU: LR1b Page ID: rerabyen Links: ------ [1] h...
Our Answer: While it would be OK to use another vent-free unit with this corner mantel, it is designed only for use with the Vantage Hearth 32" vent-free fireboxes. Please see an example of one here: Vantage Hearth LogMate VFB32C Vent-Free Circulatin...
Our Answer: I sincerely apologize but the burner pipe, listed as item E in the picture, is no longer available. The manufacturer is now only selling the complete lighters with the coupling included. From Page: CPF-47115 [1] Manufacturer's Product...
Our Answer: Given that this is a bio-fuel fireplace, operating costs will be minimal. It will depend largely on the cost of the fuel that you purchase. Each type of fuel (there are three total) can hold 15 ounces of fuel and can burn for 2 hours. Thi...
Our Answer: All of the Stovebright paints will dry to a satin finish. I have called Forrest Paint Company, the makers of Stovebright paint, and they advised that they do not currently make a high gloss paint or coating at this time. In Response to ...
Our Answer: This product will only connect a masonry flue to Security brand, double wall black stovepipe. It is not designed to connect to a stainless, class A chimney, as the diameter is different. You can view an example of the Security stovepipe h...
Our Answer: Please see this item: Gelco Stainless Steel 13 in. x 17 in. Base 2 Foot Flue Stretcher [1] This is a stainless steel 13 in. x 17 in. Base 2 Foot Flue Stretcher, which appears to be exactly what you need. In Response to Question: My n...
Our Answer: Our Copperfield 58F rods are probably our most flexible cleaning rods. They measure only .37" in diameter. From Page: CPF-2350-PFLEX [1] Manufacturer's Product Number: PF-34-3 Our SKU: PF-34-3 Page ID: cpf-2350-pflex Links: -----...
Our Answer: The chimney pipe will fit snugly as it passes through the wall thimble. Inside the wall, the thimble will be framed in. Insulation can only be installed outside of this framework. The exterior half of the wall thimble should be sealed aga...
Our Answer: Unfortunately, Simpson Dura-Vent, the manufacturer of the PelletVent Pro pipe, only makes this adaptor to class A chimney pipe, which converts PelletVent Pro to DuraTech or DuraPlus. There is no adaptor manufactured to convert the PelletV...
Our Answer: This remote should not alter the flame height of your log set unless you're commanding it to do so. My first impression would be that the receiver portion is defective. However, these units do have an over-temp shut off feature. If the re...
Our Answer: This installation is definitely possible. These units only require a clearance of 2" to combustibles on either side. Your window will not be affected. From Page: CUI-VFD26FP20L [1] Manufacturer's Product Number: VFD-26-FP20LN Our S...
Our Answer: Thank you for shopping at eFireplaceStore.com. It is very feasible to accomplish what you are attempting with rigid B-vent pipe. And Metal Fab is a fine brand of pipe with which to do it. ideally, you would begin your venting run with a C...
Our Answer: I have not come across one of these that is adjustable. However, they are available in different lengths. This one has an overall length of 19". In Response to Question: I have this type of damper control at the face of my fireplace....
Our Answer: You may indeed install a wood burning insert into a zero clearance box as long as it has the required dimensions and is rated to accept an insert. The webpage for this item has both the installation manual and manufacturer's brochure for ...
Our Answer: Unfortunately, not. Differing brands of chimney pipe cannot be mixed. From Page: CPF-77926 [1] Manufacturer's Product Number: 6T-TWK Our SKU: 6T-TWK Page ID: cpf-77926 Links: ------ [1] http://www.efireplacestore.com/cpf-77926.h...
Our Answer: That is correct. Per the manufacturer specifications, this is the proper door assembly for the current model of Vantage Hearth Winston. From Page: FSD-BDMO42E [1] Manufacturer's Product Number: BDMO42E Our SKU: BDMO42E Page ID: fs...
Our Answer: You will need to select a door and louver option to complete the unit. This will complete the fireplace and make it ready for installation. The blower assembly and damper control kit are purely optional. They are not required for installa...
Our Answer: Most vent-free units are not legal in California, but you would need to check with your city hall and your local building inspector to be sure. From Page: CUI-VFL28IN72 [1] Manufacturer's Product Number: VFL-28IN-72N Our SKU: VFL-2...
Our Answer: Unfortunately, Napoleon only makes one size surround for this insert and it covers openings as large as 42" Wide by 25" High. There currently are no trim kits available that would allow this unit to fully cover your opening. You may be in...
Our Answer: This product is indeed designed to repair wood burning stoves. It will flex with your stove as it expands and contracts. In Response to Question: What is the best High Temperature Sealant or Cement that I could use to fill a narrow c...
Our Answer: These two units are similar. However, the Premium line does offer a few things that the Performance does not. The Premium line units offer a textured powder coated painted finish, while the Performance line features a standard black finis...
Our Answer: This screen has a very fine mesh, and while you will be able to see the flames, the view will be a bit obstructed and somewhat unclear. From Page: CPF-61029 [1] Manufacturer's Product Number: 61029 Our SKU: 61029 Page ID: cpf-610...
Our Answer: Per the manual for your fireplace, you'll want to use the BD42 door kit, not the BDB42 kit. Please follow the below link to view it. FMI Extruded Aluminum Bi-Fold Glass Doors for 42 Inch Mission Gas Fireplace - Black [1] From Page: FSD-...
Our Answer: While we do have several electric appliances with a cherry finish, like the three below links. Only the Petit Classic offers a blower. Classic Flame Saranac Electric Fireplace with Roasted Cherry Mantel [1] Classic Flame Nantucket Dual Co...
Our Answer: This adaptor is designed for use with our Selkirk DSP Double-Wall stove pipe. This Double-Wall pipe only requires a 6" clearance to combustibles. As such, your 8" of brick would be sufficient. However, if you are intending to use Single-W...
Our Answer: The total weight for this tool set is 16 pounds. From Page: NPL-TS3 [1] Manufacturer's Product Number: TS3 Our SKU: TS3 Page ID: npl-ts3 Links: ------ [1] http://www.efireplacestore.com/npl-ts3.html
Our Answer: Unfortunately, this unit does not offer variability in its burner control. A similar unit that does offer variable control would be our Napoleon NPL-GVF36. You may view it here: Napoleon GVF36 Vent Free Gas Fireplace [1] Please keep in mi...
Our Answer: A circulating fireplace will have louvers manufactured into the face of the unit. This allows for natural convection of heat from the unit when it is being used and also allows the use of an electric blower to further aid convection. A no...
Our Answer: This unit will operate just fine during a power failure. Only the optional blower would be affected by the lack of electricity. From Page: MAJ-24VFSPVC [1] Manufacturer's Product Number: 24VFSPVC Our SKU: 24VFSPVC Page ID: maj-24...
Our Answer: This unit's shipping weight is just over 600 lbs. From Page: CUI-VI368ST [1] Manufacturer's Product Number: VI368ST Our SKU: VI368ST Page ID: cui-vi368st Links: ------ [1] http://www.efireplacestore.com/cui-vi368st.html
Our Answer: I wanted to correct what I sent you earlier. It turns out that when filled to capacity, this fireplace's ethanol tank will burn for approximately 11 hours on maximum input. From Page: NPL-WMFE3 [1] Manufacturer's Product Number: WMFE3...
Our Answer: You certainly can. This is the main advantage of a non-circulating model and allows you to customize the fireplace much more than a circulating model. From Page: CUI-VB421 [1] Manufacturer's Product Number: VB421 Our SKU: VB421 Pa...
Our Answer: Unfortunately, that is not an option, as these mantels are only made as shown and there is no option for customization. In Response to Question: I really like this mantel, my problem is that my fireplace is off center in the brick on...
Our Answer: Please see the installation instructions and diagram for this lintel mount hood by downloading the owner's manual on this page. From Page: FSD-EUCH4L [1] Manufacturer's Product Number: EUCH4L Our SKU: EUCH4L Page ID: fsd-euch4l L...
Our Answer: We have adaptors available in single and double wall that may work for you. Our single wall DuraBlack Double-Skirted Adaptor features an interior diameter of 7 5/8. Please view it here: Dura-Black Welded Steel Double-Skirted Stovepipe to ...
Our Answer: Indeed, these Rutland gloves are manufactured at the company's manufacturing facility in Jacksonville, IL. From Page: RUT-702 [1] Manufacturer's Product Number: 702 Our SKU: 702 Page ID: rut-702 Links: ------ [1] http://www.efire...
Our Answer: Venting for this fireplace must be purchased separately. From Page: MAJ-500DVBLNSC7 [1] Manufacturer's Product Number: 500DVBLNSC7 Our SKU: 500DVBLNSC7 Page ID: maj-500dvblnsc7 Links: ------ [1] http://www.efireplacestore.com/ma...
Our Answer: We only carry a few polishes. Check out this one by Flitz: Flitz Metal Polish - 44100 [1] It's designed to work on all metals including brass. From Page: UF-S-2092 [2] Manufacturer's Product Number: S-2092 Our SKU: S-2092 Page ID:...
Our Answer: This venting kit measures 3" as the inner diameter. It is designed for appliances with a 3" flue collar. From Page: FSD-03ALKTR035 [1] Manufacturer's Product Number: 03ALKTR035 Our SKU: 03ALKTR035 Page ID: fsd-03alktr035 Links: -...
Our Answer: There would be batteries in the receiver and the transmitter portion of your remote control. The 4 AAs belong in the black receiver box. But the transmitter takes 2 AAA batteries. Are you getting any response at all from the receiver when...
Our Answer: This fireplace can indeed be installed in the manner you want, but you do need 9 inches of clearance on either side of the fireplace before your next appliance. The fireplace would need to be installed flush with the walls on both sides a...
Our Answer: That would be perfectly acceptable. As long as the fireplace meets the required dimensions for installation, this burner can be used without a problem. From Page: FSD-FC14-R-LP [1] Manufacturer's Product Number: FC14-R-LP Our SKU: F...
Our Answer: Unfortunately, no, that is not an option with this stove. We apologize for this inconvenience. From Page: FSD-OB02411 [1] Manufacturer's Product Number: OB02411 Our SKU: OB02411 Page ID: fsd-ob02411 Links: ------ [1] http://www....
Our Answer: Unfortunately, not. We currently only carry the 5088 furnace. From Page: CUI-5088LP [1] Manufacturer's Product Number: 5088LP Our SKU: 5088LP Page ID: cui-5088lp Links: ------ [1] http://www.efireplacestore.com/cui-5088lp.html
Our Answer: This unit is deigned to be installed into either a masonry fireplace or a pre-fab fireplace designed to receive an insert. I do not believe it could be installed into your furnace. In Response to Question: We have a country flame woo...
Our Answer: These curtains feature 1/4" mesh. This difference in mesh diameter explains the price difference. You may view our below option for a mesh panel rod kit. Woodfield Hanging Fireplace Spark Screen Rod Kit [1] In Response to Question: I ...
Our Answer: The flue comes out of the top of this furnace, as it will with almost every woodburning stove or furnace, with few exceptions. From Page: USS-1802G [1] Manufacturer's Product Number: 1802G Our SKU: 1802G Page ID: uss-1802g Links...
Our Answer: For the 8" MetalBest pipe, you will need this item, the attic insulation shield, a firestop (MetalBest Ultra-Temp 8 Inch Diameter Chimney Pipe Firestop/Joist Shield [1]), a flashing (MetalBest Ultra-Temp 8 Inch Diameter Chimney Pipe Roof ...
Our Answer: To be sure that this fireplace would be a suitable replacement, I would encourage you to check the owner's manual to make sure the dimensions of this unit would work with your current set-up for the Bay 36. You can find the framing dimens...
Our Answer: You may install these panels to cover the interior walls of your fireplace. However, a cheaper option may be to sand off the existing paint and go back with High Temp rated paint. Please follow the below link to see one of our options. St...
Our Answer: The pictured mantel is unfortunately one no longer offered by Napoleon. However, you can find the mantel closest to this style by following the below link. Wood Fireplace Mantels [1] You'll want to view the Princess model in the large var...
Our Answer: Leaving the fan plugged in and on will have no negative effect on your unit - even if it does cycle on and off frequently. However, if you'd prefer for the fan not to run, then by all means turn it off until you are ready for it to run. ...
Our Answer: Unfortunately, no, our FSD-36EB110-GRT does not have an adjustable faceplate. It is designed to receive finishing material, such as drywall, right up to the sides of the unit. However, you may be interested in our Napoleon EF31 Casaloma F...
Our Answer: Our stove paint is specifically designed for high temp applications. It should not peel or blister if applied correctly. We recommend preparing the front of your fireplace to make sure that the paint adheres correctly. You'll want to suff...
Our Answer: This will work just fine in your application. Don't forget to add on any needed gasket cement. For your convenience, I have included a direct link to the gasket cement below: AW Perkins Stove Gasket Cement Tube [1] From Page: FSD-160 [2...
Our Answer: This double-barrel kit only includes the barrel mounts and two 6" flue collars. It is to be used with the US Stove Barrel Stove Kit, which you can find at this link: US Stove Barrel Stove Kit [1] This kit comes with legs, a door, and 6" f...
Our Answer: The item you inquired about, the Napoleon Centrifugal Fireplace Blower Kit, is made only to work in the Napoleon NZ-26 and NZ-26WI Wood Burning Fireplaces. You can see how it is installed in the NZ-26 in the owner's manual for that wood-b...
Our Answer: Unfortunately, 36" is as large as these see-though units are offered. From Page: CUI-FBST [1] Manufacturer's Product Number: FBST Our SKU: FBST Page ID: cui-fbst Links: ------ [1] http://www.efireplacestore.com/cui-fbst.html
Our Answer: There is no BTU rating for this item because it does not include logs or a burner. This item is only a universal vent-free firebox, and it accepts any set of ventless gas logs with a vent-free burner. We sell ventless gas log sets that wi...
Our Answer: This unit does not have a BTU output rating assigned to it, as this will depend on the type of wood burned, moisture content of the wood, and fire tending skills. On average, a fireplace of this size can produce 60,000 to 120,000 BTUs. ...
Our Answer: There are two possibilities here: 1. The trim collar you ordered is adjustable, and it can be used with 7- or 8-inch inner diameter ceiling supports. It is possible that it came ready to install with a 7-inch, and you need to adjust the c...
Our Answer: Unfortunately, to burn pellets, you will need an appliance designed to do so. There is no other way to convert a wood burning fireplace to a pellet burning unit. From Page: NPL-AK8 [1] Manufacturer's Product Number: AK8 Our SKU: AK...
Our Answer: This unit (CUI-VB361) can receive a black door kit instead of the brass kit shown. You'll want item number FSD-BDB36, which can be found on our website. This unit includes a screen curtain. This unit cannot use a blower as it is non-circu...
Our Answer: Unfortunately, we do not have samples available. You look at the inset picture on this item page to view a color card by Stove Bright, though. From Page: CPF-43230 [1] Manufacturer's Product Number: 6195 Our SKU: 6195 Page ID: cpf...
Our Answer: Kerosene is the safest fuel option for this lighter. From Page: CPF-61098 [1] Manufacturer's Product Number: 61098 Our SKU: 61098 Page ID: cpf-61098 Links: ------ [1] http://www.efireplacestore.com/cpf-61098.html
Our Answer: Unfortunately, due to the lack of an effective ignition system, the manufacturer's units that we carry do not have an electronic ignition system. Standing pilot systems have proven much more reliable and as a result, are still the most pr...
Our Answer: This price is indeed for the complete mantel--the shelf, the breastboard, and the legs. From Page: CUI-MFL48PG [1] Manufacturer's Product Number: MFL-48-PG Our SKU: MFL-48-PG Page ID: cui-mfl48pg Links: ------ [1] http://www.efi...
Our Answer: This item is just a firebox. No gas log kit is included. Per its interior dimension, it should be plenty capable of accommodating one of our 30" vent-free log kits. This firebox cannot be adapted to a vented appliance. To install this uni...
Our Answer: Unfortunately, the green cast iron surround has been discontinued by Napoleon. It is now only available in black cast iron or porcelain brown. From Page: NPL-EPI-1101P [1] Manufacturer's Product Number: EPI-1101P Our SKU: EPI-1101P ...
Our Answer: This surround is designed to work with Empire's medium Innsbrook fireplaces. This fireplace measures 22 3/4 H x 31 W. The surround kit panels are only about 6" wide. We do not currently carry generic or universal fit flashings. We might, ...
Our Answer: In fact, Peterson gas logs are great products and we have enjoyed our relationship with this manufacturer. First of all, if you are interested in any sort of control valve, I would recommend that you also pursue replacing your current gas...
Our Answer: These doors are made for use only with the Majestic Royalton 42" Fireplace. You can see that fireplace here: Majestic 42 Inch Royalton Circulating Wood Burning Fireplace [1] From Page: MAJ-42GDKBK [2] Manufacturer's Product Number: 4...
Our Answer: This screen indeed has a brass-plated finish. From Page: UF-S-2092 [1] Manufacturer's Product Number: S-2092 Our SKU: S-2092 Page ID: fsd-s-2092 Links: ------ [1] http://www.efireplacestore.com/fsd-s-2092.html
Our Answer: We do sell shorter lengths. In the search box, type Rutland Fiberglass Grapho-Glas Stove Gasket with Gasket Cement Kit. If you need shorter lengths, please search Rutland Fiberglass Grapho-Glas Stove Gasket. Here's a link to the cement, s...
Our Answer: This flashing is approximately 18 gauge. From Page: NPL-TI-2201 [1] Manufacturer's Product Number: EPI22 Our SKU: EPI22 Page ID: npl-ti-2201 Links: ------ [1] http://www.efireplacestore.com/npl-ti-2201.html
Our Answer: We offer see-through log sets in vented and vent free by R. H. Peterson. Both feature ceramic refractory logs that are designed to absorb heat and send it into the room. Please follow this link to view our log selection. See Thru Gas Logs...
Our Answer: This fireplace will have a shipping weight of approximately 215 lbs. From Page: MAJ-CLLDVPSC [1] Manufacturer's Product Number: CLLDVPSC Our SKU: CLLDVPSC Page ID: maj-clldvpsc Links: ------ [1] http://www.efireplacestore.com/ma...
Our Answer: The approximate shipping weight for this tool set is 25 pounds. From Page: CPF-61217 [1] Manufacturer's Product Number: 61217 Our SKU: 61217 Page ID: cpf-61217 Links: ------ [1] http://www.efireplacestore.com/cpf-61217.html
Our Answer: Certainly. This cap is designed to fit both Class A and Type B vents. It can also be used in lower temperature applications that use PVC. Because it is a push-in type of cap, I highly recommend using metal screws to secure it once it is i...
Our Answer: Parge coating is basically the application of a relatively thin coat of mortar to a masonry surface - similar to a skim coat. This product applies easily with a trowel or by hand. However, gaining access to the smoke chamber can sometimes...
Our Answer: This firebox weighs 169 lbs. From Page: MAJ-BUF500 [1] Manufacturer's Product Number: BUF500 Our SKU: BUF500 Page ID: maj-buf500 Links: ------ [1] http://www.efireplacestore.com/maj-buf500.html
Our Answer: This screen is about 27" tall at its highest point, and the base has approximately 6-7" thickness, front to back. From Page: UF-S-2091 [1] Manufacturer's Product Number: S-2091 Our SKU: S-2091 Page ID: uf-s-2091 Links: ------ [1]...
Our Answer: The height of the opening for this mantel is approximately 22 1/4" tall. It is designed to be an exact match for the Vantage Hearth VGMRN fireplace. It can be seen at the link below: Vantage Hearth Mini Classic Hearth VGMR Vent-Free Compa...
Our Answer: Unfortunately, this conversion kit has been discontinued by Monessen and is no longer available. I have verified that Monessen does not carry an equivalent kit at this time. I apologize that I cannot provide this kit any longer. From Pa...
Our Answer: This item is approximately 18" from end to end and measures about 1 3/4" tall, excluding the hooks. From Page: CPF-71899 [1] Manufacturer's Product Number: WH-04 Our SKU: WH-04 Page ID: cpf-71899 Links: ------ [1] http://www.efir...
Our Answer: This is the only stove made by Napoleon that has a removable hot plate and lifter with stainless steel gasket to mark "Hot Zones." From Page: NPL-1150P [1] Manufacturer's Product Number: 1150P Our SKU: 1150P Page ID: npl-1150p Li...
Our Answer: Primed means that it will come with primer already applied so that it ready to paint. Unfinished will not have the primer already applied. From Page: CUI-MS48PG [1] Manufacturer's Product Number: MS-48-PG Our SKU: MS-48-PG Page ID...
Our Answer: These Smoke Guards conveniently fit fireplaces from 28 1/2" to 48" wide. Generally, the 4" unit is sufficient. However, for exceedingly tall fireplaces, the 6" is recommended. From Page: CPF-05020 [1] Manufacturer's Product Number: F...
Our Answer: You will need 1/2" minimum inner diameter supply pipe, and if the gas line is longer than 20 feet, a larger diameter may be necessary. The BTU output for this set is 75,000 BTUs. Please note: A manual valve needed (a key in your wall/floo...
Our Answer: There is not a thermostat available for this stove per se; however there is a heat range button on the stove's control panel that effectively controls the heat output of the appliance. From Page: USS-5824 [1] Manufacturer's Product Nu...
Our Answer: The center panel of this screen measures 28.5" wide. Each side panel has a width of 12.75". From Page: CPF-61038 [1] Manufacturer's Product Number: 61038 Our SKU: 61038 Page ID: cpf-61038 Links: ------ [1] http://www.efireplaces...
Our Answer: Yes, please see the owner's manual here: Owner's Manual for the Vantage Hearth Odyssey Vent-Free Outdoor Gas Fireplace [1] From Page: CUI-VO36RB [2] Manufacturer's Product Number: VO36NRB Our SKU: VO36NRB Page ID: cui-vo36rb Link...
Our Answer: These tubes are your secondary air supply. By providing the fire with the necessary air for combustion, they ensure that it remains burning at its most efficient level. From Page: FSD-OB02211 [1] Manufacturer's Product Number: OB0221...
Our Answer: The FSD-10826 is, indeed, a half round hearth rug. The picture on our website depicts the color and design of the rug, but is not a picture of the actual rug itself. From Page: FSD-10826 [1] Manufacturer's Product Number: 10826 Our ...
Our Answer: These tools are approximately 25" long. Unfortunately, we do not have any information regarding their diameter. We ship these tools directly from the manufacturer and do not have them here to inspect and measure. From Page: ADC-800324 [...
Our Answer: This price will indeed include just the fireplace itself. This unit utilizes FMI's 8" Class A chimney pipe. The components can be viewed here: FMI Class A Chimney Pipe [1] Please let us know if you would like a quote for the needed chimne...
Our Answer: This horizontal terminal cap measures 16" wide and 16" high, with a 14" depth (protrusion) from the wall. This terminal is only for use with Napoleon's 8" inner diameter and 10" outer diameter flexible direct vent gas pipe, which is used ...
Our Answer: No. This unit if for indoor use only. For a selection of fireplaces that are designed for outdoor applications, please go to the following link: Patio Fireplaces [1] From Page: CUI-VC42L1 [2] Manufacturer's Product Number: VC42L1 Ou...
Our Answer: The length of pipe for the price listed on the page is 9 inches. This pipe is also available in 12-, 24-, and 36-inch pieces. The price adjustments for those sizes are noted in parentheses in the drop-down menu located below the pricing i...
Our Answer: Rather well, depending on the space. This unit produces 4,600 BTUs of heat. This amount is satisfactory for about 131 square feet. Anything larger than this and the unit will simply provide supplemental heat. From Page: FSD-23DM537EWAL...
Our Answer: These trim kits attach with specially designed magnets that are made to withstand the heat of your fireplace. From Page: NPL-GIZUT [1] Manufacturer's Product Number: GIZUT-B Our SKU: GIZUT-B Page ID: npl-gizut Links: ------ [1] ...
Our Answer: This cover is designed to fit a rack that measures 26" L x 13" W x 33" H. From Page: HYC-SLRC-S [1] Manufacturer's Product Number: SLRC-S Our SKU: SLRC-S Page ID: hyc-slrc-s Links: ------ [1] http://www.efireplacestore.com/hyc-s...
Our Answer: Olefin is a highly fire retardant material and can withstand burning embers or coals rolling onto the rug. The material will only singe under extreme circumstances, rather than smolder or burn. From Page: CPF-72074 [1] Manufacturer's ...
Our Answer: Per the manufacturer, this Type 2 board has a thickness of 7/16". From Page: HYC-T2UL2832ST-1C [1] Manufacturer's Product Number: T2UL2832ST-1C Our SKU: T2UL2832ST-1C Page ID: hyc-t2ul2832st-1c Links: ------ [1] http://www.efirep...
Our Answer: Per the manufacturer, the inward feet are positioned 5 inches from the outside edges of the screen's frame. From Page: CPF-61227 [1] Manufacturer's Product Number: 61227 Our SKU: 61227 Page ID: cpf-61227 Links: ------ [1] http://...
Our Answer: This item is the black firebox only, and does not include the gray marble surround pictured. This unit is only available in black. From Page: FSD-FGPN [1] Manufacturer's Product Number: FGPN Our SKU: FGPN Page ID: fsd-fgpn Links...
Our Answer: This canvas log carrier is 12" wide. From Page: ADC-304001 [1] Manufacturer's Product Number: X304001 Our SKU: X304001 Page ID: adc-304001 Links: ------ [1] http://www.efireplacestore.com/adc-304001.html
Our Answer: There will be no issue with installing an LCD TV above this stove, as long as the projection requirements that are outlined in the owner's manual (which can be downloaded on this item page) are observed. The unit will only allow a mantel ...
Our Answer: The mesh screen height for this cap is 6 inches. From Page: HYC-SS1313U [1] Manufacturer's Product Number: SS1313U Our SKU: SS1313U Page ID: hyc-ss1313u Links: ------ [1] http://www.efireplacestore.com/hyc-ss1313u.html
Our Answer: This particular unit is 41" wide in the front, 32" wide in the back, 37 5/8" tall, and 18" deep. From Page: CUI-LCUF36C-R [1] Manufacturer's Product Number: LCUF36C-R Our SKU: LCUF36C-R Page ID: lcunlowrivef Links: ------ [1] htt...
Our Answer: While we do not offer any mantel shelves by Pearl Mantels in a 48" size, we do carry a couple of shelves manufactured by Empire and Trotter. They can be seen below: Empire 48 Inch Profile Wooden Mantel Shelf with Standard Trim - Primed [1...
Our Answer: "Lintel mount" refers to the method of mounting a fireplace hood. The actual mounting occurs on the underside of the lintel, or the "ceiling" of the firebox. You would anchor your hood with screws vertically upward into the lintel of the ...
Our Answer: "These items are indeed available for purchase. Please view the following links to see the items: Lock-Top 50 Foot Damper Cable [1] Lock-Top Damper Extra Hardware Pack [2] Please keep in mind that these are designed for use with the Lock-...
Our Answer: No. The Selkirk SuperVent pipe has a 7" inner diameter, and the appropriate adaptor/anchor plate for that pipe can be located here: SuperVent All-Fuel Chimney Pipe to Fireplace Adaptor Plate with Stainless Steel Collar - 7 Inch Diameter [...
Our Answer: If you look below the item picture on this page, you will see a swatch of colors from Stove Bright. Simply scroll your mouse over the palette and you will see an example of some (not all) of the colors available. From Page: CPF-43220 [1...
Our Answer: This is a non-catalytic unit. From Page: USS-1261 [1] Manufacturer's Product Number: 1261 Our SKU: 1261 Page ID: uss-1261 Links: ------ [1] http://www.efireplacestore.com/uss-1261.html
Our Answer: Unfortunately, not. We do not currently offer the individual components of this remote control. From Page: FSD-SKY-MRCK [1] Manufacturer's Product Number: SKY-MRCK Our SKU: SKY-MRCK Page ID: fsd-sky-mrck Links: ------ [1] http:/...
Our Answer: This is actually a decorative surround, which is meant to be used in conjunction with the loft direct vent fireplace [1]. The dimensions of the unit and surround can be readily viewed in the features section of the unit's item page. Fro...
Our Answer: The owner's manual for this unit only lists the Empire Battery-Operated Remote Control as a compatible option. This remote has only on/off functionality with no thermostat, and it can be found here: Empire Battery-Operated Remote Control ...
Our Answer: No, we're sorry, but this will not work with your fireplace. The Majestic DVR33 is a direct vent fireplace. This fresh air kit is only for use with Majestic's indoor and outdoor Biltmore Wood Burning Fireplaces, Designer Wood Burning Fire...
Our Answer: The outer diameter of the Majestic 8" triple wall pipe is 13.5". From Page: MAJ-81 [1] Manufacturer's Product Number: 81 Our SKU: 81 Page ID: maj-81 Links: ------ [1] http://www.efireplacestore.com/maj-81.html
Our Answer: As the shield comes from the manufacturer, no there is not. The only way to install the shield around an existing chimney would be to make a vertical cut in the shield assembly, wrap it around the pipe, then rivet the assembly back togeth...
Our Answer: There are actually no venting components included with the purchase of this fireplace. We do not want to send you something you do not need. If you're interested in a simple straight out vent, then you'll only need a few items. You'll nee...
Our Answer: This unit is pictured with the optional bay front and safety screen. This unit can only be used with the included Phazer glowing log set. There currently is no glass kit option to add. From Page: NPL-BGD33NRE [1] Manufacturer's Produ...
Our Answer: Please see the following link for the owner's manual/installation instructions for this blower: Item Page [1] Please note that this blower is only for use with certain FMI/Vantage Hearth/Vanguard/DESA fireplaces. If you provide the make/m...
Our Answer: If you want to take out an existing fireplace and replace it with a woodburning unit like this, yes, you would need to change the pipe as well. We sell the class A chimney pipe that you would need to connect to this 42" Royalton unit. How...
Our Answer: Here are the part numbers and descriptions for the items you'll need for a complete replacement door: #SE24134 CAST IRON DOOR W/HANDLE #SE39102 GLASS RETAINER W/GASKET #SE39105-01 CERAMIC GLASS W/GASKET From Page: FSD-OA10090 [1] Man...
Our Answer: Pictures of the alternate door designs can be viewed at the following link: http://www.miragestone.com/index.cfm/fuseaction/gallery.viewCategory/catID/3/index.htm [1] Please click the link of each picture thumbnail to view the different d...
Our Answer: Many of the Goods of the Woods brand rugs meet 1631 FF1-70 flammability requirements and will state as much in the item features. You can be assured that any rug that carries this certification is a highly flame retardant model and will ...
Our Answer: We have this pipe available in 12-, 24- and 48-inch length pieces. Please see these options in the drop-down menu located under the pricing information. The numbers in parentheses note the appropriate price adjustment for the 24- and 48-i...
Our Answer: You are correct about the ceiling support box. If you have a flat ceiling in a relatively short room (8' - 9' ceiling), I'd recommend our round ceiling support box. A taller, cathedral ceiling would require a cathedral ceiling support box...
Our Answer: Yes, two sets of louvers would need to be purchased for the Empire see-thru fireplaces and fireboxes. From Page: CUI-FBG36L [1] Manufacturer's Product Number: FBG-36-LBL Our SKU: FBG-36-LBL Page ID: cui-fbg36lbl Links: ------ [1...
Our Answer: On item CPF-77916, the 6 inch refers to inner diameter. From Page: CPF-77916 [1] Manufacturer's Product Number: 6T-JS Our SKU: 6T-JS Page ID: cpf-77916 Links: ------ [1] http://www.efireplacestore.com/cpf-77916.html
Our Answer: The "zero clearance" that is being mentioned is in reference to a zero clearance fireplace. Zero clearance (manufactured) fireplaces are very shallow by nature and this grate is specially designed for use in such a unit. The grate is a me...
Our Answer: This item is silver. However, we do also offer this kettle in black. From Page: CPF-46295 [1] Manufacturer's Product Number: HK-S Our SKU: HK-S Page ID: cpf-46295 Links: ------ [1] http://www.efireplacestore.com/cpf-46295.html
Our Answer: The measurements for this item indicate that it is 48 inches wide on the straight edge and will be 27 inches deep at the center of the arch. From Page: FSD-10806 [1] Manufacturer's Product Number: 10806 Our SKU: 10806 Page ID: fsd...
Our Answer: Most stoves use two separate gaskets to seal the stove body. One gasket will be pressed between the edges of the stove glass and the door assembly and the other gasket will fit into the channel that is cast into the face of the stove, sea...
Our Answer: This item is actually a decorative surround for the large Innsbrook fireplace insert. The insert itself, is the Innsbrook Large Direct Vent Gas Fireplace Insert - Natural Gas - DV-35IN-33LN [1], which is designed to retrofit a standard ma...
Our Answer: This rug will only serve as floor protection for a combustible surface in front of the fireplace. If the installation instructions are truly calling for a 16 inch noncombustible hearth, this will not work. A noncombustible hearth, made of...
Our Answer: This unit only requires electricity if you are installing the optional blower assembly. From Page: FSD-FGPN [1] Manufacturer's Product Number: FGPN Our SKU: FGPN Page ID: fsd-fgpn Links: ------ [1] http://www.efireplacestore.com...
Our Answer: This unit is indeed ventless. It cannot be used with propane fuel but the below unit can. Florence Mid Height Corner Mantel with Arched Propane Fireplace [1] These units are compliant to ANSI Z21.11.2b-2004 and feature an Oxygen Depletion...
Our Answer: Actually, this item is just the logs only, without a burner or valve system. It is available as a complete system with on/off, variable flame, and electronic control. The complete kits can be seen at the following links: Real Fyre 16\" Bu...
Our Answer: Each manufacturer is different, Peterson manufacturers their logs with their burners in mind. Due to the individual characteristics of differing manufacturer's burner system's there is no way to know how these logs will perform on another...
Our Answer: These logs are 14" long. From Page: PTS-SB-BONUS [1] Manufacturer's Product Number: SB-BONUS Our SKU: SB-BONUS Page ID: pts-sb-bonus Links: ------ [1] http://www.efireplacestore.com/pts-sb-bonus.html
Our Answer: This particular gas starter is designed to connect to a gas line that enters the fireplace in the center of fireplace floor. It simply threads right onto the gas inlet. From Page: CPF-47120 [1] Manufacturer's Product Number: 47120 ...
Our Answer: Ceramic liner is the faux brick found within gas fireplaces. They are lightweight and cannot withstand the heat of a wood fire. All of our ceramic fiber is fireplace model-specific. For example, this item is for use only with Empire's 42"...
Our Answer: FMI provided a special refractory mortar for setting the firebrick into place. It is necessary to use this mortar, as regular brick mortar can overheat and explode, depending on the material it is made of. Please see page 28 of the manual...
Our Answer: Unfortunately, we do not have a 20 x 20 fireback with the Fleur De Lys design like this one. Please see the following link for our only 20 x 20 fireback: Copperfield Stainless Steel Radiant Fireback - 20-in. X 20-in. [1] From Page: ADC-...
Our Answer: This item is manufactured in China. From Page: CPF-61274 [1] Manufacturer's Product Number: 61274 Our SKU: 61274 Page ID: cpf-61274 Links: ------ [1] http://www.efireplacestore.com/cpf-61274.html
Our Answer: Please see page 4 of the owner's manual for detailed dimensions and drawings of the 42" unit. You can download the manual on this page. Be sure to look at page 4, as the specs for the 36" and 50" unit are also included in this owner's man...
Our Answer: These 9" logs are both flat on the bottom. The larger of the two measures about 2" tall and 2" deep, while the smaller log measures about 1.5" tall and 2" deep. From Page: PTS-BR-2 [1] Manufacturer's Product Number: BR-2 Our SKU: B...
Our Answer: Wood stoves are pretty easy to vent. We'd start you out with an appliance adaptor to get the run started. We'd then use either single or double wall stove pipe up to the ceiling. We'd transition to chimney pipe at the ceiling through a ro...
Our Answer: This unit has a standing pilot that must be lit like most gas water heaters or furnaces. You will need to access the gas valve on the heater and switch the control knob to pilot. You will then need to use a match or lighter to light the p...
Our Answer: We do indeed carry the type b venting for this unit and can assemble a quote for the needed pipe if you like. The unit also requires a type bw adapter to pass the pipe from the stud cavity the unit is mounted into, through the wall header...
Our Answer: Since your model of stove uses a standard millivolt gas valve, this remote will be a suitable model to operate it. The gas valve on the stove has the standard TP, TH, TP/TH connections and the remote instructions will guide you through th...
Our Answer: Yes, please see page 39 of the owner's manual for a detailed view of the brick in this stove. The owner's manual is available for download on this product's page. From Page: SBI-DB03185 [1] Manufacturer's Product Number: DB03185 Our...
Our Answer: This unit is indeed available in a top-vent version, which can be seen here [1]. The unit will operate at your elevation, but the air shutter will need to be adjusted to the specifications covered in the manual. From Page: MAJ-CDVR33NSC...
Our Answer: This unit has a BTU rating of 13,000 - 18,000 for either natural gas or propane. It efficiently heats up to 640 sq. ft. From Page: CUI-CDVT33NSC7 [1] Manufacturer's Product Number: CDVT33NSC7 Our SKU: CDVT33NSC7 Page ID: cui-cdvt3...
Our Answer: This ash bin is constructed of steel, but it is not stainless steel. From Page: UF-C-1736 [1] Manufacturer's Product Number: C-1736 Our SKU: C-1736 Page ID: uf-c-1736 Links: ------ [1] http://www.efireplacestore.com/uf-c-1736.ht...
Our Answer: You can find detailed dimensions and a drawing of this unit on page 6 of the owner's manual, which you can download on this item page. Please be sure to look at page 6, as this manual is the same for the 36" and 50" unit, and those specif...
Our Answer: This decorative log set is to be placed in the WDV600TSC fireplace with 2" of extra space from the front and back of the unit, so there should be room for the set to fit. Please keep in mind however, that we cannot guarantee proper operat...
Our Answer: If proper clearances are maintained to any of the sprinkler controls or the heads themselves, you will not have a problem. Ethanol is a very clean burning, lower BTU output fuel. The small amount of supplemental heat produced would not af...
Our Answer: This product is manufactured from 1/2" steel. It is solid square metal and no part of it is hollow. From Page: CPF-61052 [1] Manufacturer's Product Number: 61052 Our SKU: 61052 Page ID: cpf-61052 Links: ------ [1] http://www.efir...
Our Answer: The CUI-VB421 is not advertised as a zero clearance fireplace. However, it does offer very close clearances to combustibles. The unit only requires a minimum 3/4" of clearance from combustibles at the back and sides of the fireplace. Plea...
Our Answer: Per all of your criteria, the CUI-VFD32FB0L would be a great choice. However, are you looking to completely remove your existing fireplace and install this one or were you more interested in purchasing an insert to place within your exist...
Our Answer: This cap is manufactured from 304 stainless steel. We have other models that are made from galvanized steel or 316 stainless, should you need either version. From Page: CPF-11320 [1] Manufacturer's Product Number: WSA-8 Our SKU: WSA...
Our Answer: The item you inquired about is 25,000 BTU unit, but we do have the 50,000 BTU unit available as well. It is a dual-wall furnace designed to heat two rooms at 25,000 BTU each. It is available in either natural gas or liquid propane: Empire...
Our Answer: Being an EPA exempt product, this furnace does not have a tested efficiency rating by U.S. Stove. Similar non-EPA furnaces that are manufactured by other companies that have gone through efficiency testing usually have an efficiency ratin...
Our Answer: Unfortunately, this fireplace uses 8" inner diameter pipe, and it must be vented with the FMI 8" inner diameter class A chimney pipe. You can see an example of this pipe at this link: FMI Wood Fireplace 8-in. Diameter Chimney Venting Pipe...
Our Answer: The glass on these fireplace doors are 3/16" thick. From Page: FSD-BDB36B [1] Manufacturer's Product Number: BDB36B Our SKU: BDB36B Page ID: fsd-bdb36b Links: ------ [1] http://www.efireplacestore.com/fsd-bdb36b.html
Our Answer: A fresh air kit simply ensures that your insert has sufficient combustion air without removing an unsafe amount from your home. You'll actually need two items - an adaptor kit and also a fresh air pipe. Please follow the below links to vi...
Our Answer: This extended hood is designed to be used with 42" Breckenridge Deluxe, Premium, and Select fireboxes manufactured by Empire. Its width is not adjustable, so approximately 42" is going to be your set length on this hood. From Page: CUI...
Our Answer: Yes. There are two options available flush and louvered. Please follow the two below links to view these fireboxes. Breckenridge Premium Vent-Free See-Thru Flush Gas Firebox - 36 Inch [1] Breckenridge Premium Vent-Free See-Thru Gas Firebo...
Our Answer: We do carry the rectangular catalyst, under item number CPF-41780. It measures 2" wide, 13" long, and 2.5" deep. This is a fairly standard size, but you will need to double check your measurements to be certain. Below is a direct link to ...
Our Answer: This insert and all of our Napoleon appliances are indeed eligible for the 30% tax credit. Please follow the below link to view Napoleon's certificate of eligibility. http://napoleonfireplaces.com/Company/irs_certificate.pdf From Page: ...
Our Answer: The R-value of the Micore board is 1.03 for every 1/2 inch of board that is used. From Page: SBI-AC02565 [1] Manufacturer's Product Number: AC02565 Our SKU: AC02565 Page ID: sbi-ac02565 Links: ------ [1] http://www.efireplacestor...
Our Answer: This fireplace must be hung on a wall. It cannot be built/recessed into a wall. From Page: NPL-EFL48 [1] Manufacturer's Product Number: EFL48H Our SKU: EFL48H Page ID: npl-efl48 Links: ------ [1] http://www.efireplacestore.com/np...
Our Answer: I apologize, but we only sell this item in case quantities, due to frequent damage that could occur in shipment if less than a full case is shipped. From Page: FSD-91AW [1] Manufacturer's Product Number: 91AW Our SKU: 91AW Page ID...
Our Answer: Getting into that tee is going to be problematic for these rods. The light-duty rods are actually a better option for what you are asking, as they will bend at about a 30-degree angle. Please see those rods here: Copperfield 58F Light-Dut...
Our Answer: This frame is designed to mount to the face of the VF and VFH series fireboxes, which measure 41" wide by 34.5" tall. Because they are made for these specific units, we cannot guarantee that they will fit any other unit. From Page: MAJ-...
Our Answer: Coverage will vary depending on the material that is being painted and how many coats will ultimately be applied. If you are looking for the most basic coverage of unpainted steel, using two coats of paint, this product should be sufficie...
Our Answer: This item is designed to be used as a specific replacement for Tahoe Premium fireplaces. If you are looking for a universal liner, please check out our option by Hargrove. Hargrove Replacement Fireplace Refractory Panels - 24 inch X 40 in...
Our Answer: No,it is not. I don't know of any fireplace tool sets that we carry that are made in the United States. From Page: ADC-850310 [1] Manufacturer's Product Number: X850310 Our SKU: X850310 Page ID: adc-850310 Links: ------ [1] http:...
Our Answer: You would most likely be interested in a direct vent fireplace system as these can indeed utilize either fuel type and be vented horizontally through a block wall. Please view these units here: Direct Vent Fireplaces [1] Please let me kno...
Our Answer: Based on your dimensions and the average coverage for this paint, two cans should offer sufficient coverage for your project. From Page: CPF-43255 [1] Manufacturer's Product Number: 6283 Our SKU: 6283 Page ID: cpf-43255 Links: --...
Our Answer: The insert in this mantel is Classic Flame model #18EF010. This is their 18" 010 series insert. From Page: FSD-18DM1141EPOA-SO [1] Manufacturer's Product Number: 18DM1141EPOA/SO Our SKU: 18DM1141EPOA/SO Page ID: fsd-18dm1141epoa-s...
Our Answer: Unfortunately, we do not list our replacement liners by size. Except for our universal Hargrove panels, which you can find by following the below link. If you'd like to reply, with the model number of your fireplace and the manufacturer's...
Our Answer: Both the surface mount and the lintel mount fireplace hoods require attachment via screws. The surface mount is screwed to the front face of the fireplace and the lintel mount is screwed into the lintel of the fireplace opening. You may d...
Our Answer: Depending on the thermometer, it can indeed have a low range temperature of 100 to 250 degrees. Usually, the longer the thermometer is cold, the lower the needle will drop, as the bimetallic coil can take some time to fully relax. From ...
Our Answer: In order to do a thorough cleaning of the stove after cleaning the liner, it will be necessary to remove the upper baffles from the stove and use either an ash vac or a wet/dry vacuum to clean the flue collar of the stove. Using a polyeth...
Our Answer: The top of the mantel shelf is a charcoal color, per the manufacturer. From Page: FSD-28WM422E-AMH [1] Manufacturer's Product Number: 28WM422E-AMH Our SKU: 28WM422E-AMH Page ID: fsd-28wm422e-amh Links: ------ [1] http://www.efire...
Our Answer: All of our Real Fyre gas log sets include a length of flexible gas line to accommodate multiple locations. Most common is to have the rigid gas line closer to the middle or back of the fireplace. From Page: PTS-AOG45-24N-SS-NONE [1] ...
Our Answer: While there is no listed accompanying screen for this tool set, you may be interested in these pewter screens by UniFlame: UniFlame 3 Panel Heavy Pewter Fireplace Screen with Decorative Scrollwork [1] UniFlame Single Panel Curved Pewter F...
Our Answer: The outer diameter of this pipe is 8 inches. From Page: CPF-77895 [1] Manufacturer's Product Number: 6UT-24 Our SKU: 6UT-24 Page ID: cpf-77895 Links: ------ [1] http://www.efireplacestore.com/cpf-77895.html
Our Answer: Unfortunately, class A chimney manufacturers do not provide adapters that will make their components interchangeable. The only way to make Simpson Duravent piping work with the Air Jet chimney would be to have an adapter custom made by a ...
Our Answer: This is actually a decorative bay front for several models of Napoleon gas fireplaces. It is an accessory only and does not include the fireplace itself. Please advise on the model of heater you have now and what you would like to replace...
Our Answer: That is correct. The actual opening of the unit is closer to 23" in width and 13" in height. From Page: NPL-EFC32 [1] Manufacturer's Product Number: EFC32H Our SKU: EFC32H Page ID: npl-efc32 Links: ------ [1] http://www.efireplac...
Our Answer: Absolutely. This mantel can work with a fireplace as large as 51" wide by 42" tall. From Page: CUI-MFL52PG [1] Manufacturer's Product Number: MFL-52-PG Our SKU: MFL-52-PG Page ID: cui-mfl52pg Links: ------ [1] http://www.efirepl...
Our Answer: This unit can be operated from a 20 lb propane tank as long as a regulator is installed to ensure gas pressure is kept below 14" w.c. Please note that as the fuel supply in the tank diminishes, heater performance will also decrease. Fr...
Our Answer: This particular unit is electric, and this manufacturer does not offer a propane version. We do have numerous propane fireplaces on our site and many different styles of mantles. For the mantles, please visit this link: Wood Fireplace Man...
Our Answer: Unfortunately, you cannot recess this unit (or any of the Napoleon Ethanol Fireplaces) into the wall. It must hang on the wall, and it comes with the brackets and hardware included. From Page: NPL-WMFE3 [1] Manufacturer's Product Numb...
Our Answer: With any ventless application, you cannot mix and match logs and burners, since all components must be so meticulously engineered and tested for safety. Thus, we cannot recommend and would advise against doing what you mention. You may wa...
Our Answer: This unit ships as a top vent, but you can convert it to a rear vent. Please see page 12 of the owner's manual at this link for more information: http://lib.store.yahoo.net/lib/yhst-95622685483394/cui-dvcd42fp30manual.pdf This fireplace i...
Our Answer: The BR-21 is indeed only one log, not 4 as shown in the picture. From Page: PTS-BR-21 [1] Manufacturer's Product Number: BR-21 Our SKU: BR-21 Page ID: pts-br-21 Links: ------ [1] http://www.efireplacestore.com/pts-br-21.html
Our Answer: Per the manufacturer, it is not necessary to dig a pit for this fire ring to sit into. However, there is not an issue with doing so, should you wish to go with that look. From Page: PDM-FIGHTINGELK [1] Manufacturer's Product Number: F...
Our Answer: This particular unit can only be vented using the included through the wall venting components. The furnace will not operate efficiently with any other type of venting setup being utilized. As such, the model could only be placed on an ou...
Our Answer: To be sure, we recommend that you check with your local code enforcement. However, most areas of California prohibit the installation of any vent free appliances. From Page: FSD-V36H [1] Manufacturer's Product Number: FBF36RH Our S...
Our Answer: Yes it can. However, it is recommended to not use oil based or acrylic paint. From Page: CUI-DVX42FP33CLP [1] Manufacturer's Product Number: DVX42FP31LP Our SKU: DVX42FP31LP Page ID: cui-dvx42fp33clp Links: ------ [1] http://www...
Our Answer: No, this blower is intended for use with select Napoleon appliances only. From Page: NPL- EP65 [1] Manufacturer's Product Number: EP65 Our SKU: EP65 Page ID: nablkitwivas1 Links: ------ [1] http://www.efireplacestore.com/nablkit...
Our Answer: Peterson GeoShapes are designed to be used with Peterson's line of pan burners. These specialized burners offer a flat tray above the burner tubes that prevents the GeoShapes from impinging the flames. Please follow the below link to view...
Our Answer: According to the manufacturer, the other colors in this particular rug are a golden brown, dark brown, and a very dark green border. From Page: CPF-61145 [1] Manufacturer's Product Number: 61145 Our SKU: 61145 Page ID: cpf-61145 ...
Our Answer: Generally, this product is designed for cathedral ceilings. A separate attic insulation shield is required when a chimney system passes through an attic as tall as yours. A better support item for your installation is our round ceiling su...
Our Answer: The blower can indeed by installed into an existing unit, but it will require a bit of deconstruction of the burner assembly and gas valve. The glass face will need to be removed from the unit, then the unit will need to be shut down from...
Our Answer: Indeed, it is. It is held in place at a coupling on the valve stem with a hex head set screw. From Page: PTS-AV-18 [1] Manufacturer's Product Number: AV-18 Our SKU: AV-18 Page ID: pts-av-18 Links: ------ [1] http://www.efireplac...
Our Answer: This is only a vent-free firebox, and there are no logs or burner included. Your BTUs would depend on which ventless gas log set you get. We have a wide variety of these on our website from which to choose. Please see the following link f...
Our Answer: The Breckenridge VFD36FB0L Deluxe Vent-Free Louvered Gas Firebox that you inquired about does not come with a log set or burner, and depending on what kind of log set and burner you would purchase to go with it, the BTUs and heating area ...
Our Answer: This outside air kit comes with a 5' flex house. As long as you can drill a hole through the concrete to the outside, this kit will work for you. From Page: NPL-ZCVF42 [1] Manufacturer's Product Number: ZCVF42 Our SKU: ZCVF42 Pag...
Our Answer: Sadly, no. We are unable to swap these carriers. From Page: FSD-18516 [1] Manufacturer's Product Number: 18516 Our SKU: 18516 Page ID: fsd-18516 Links: ------ [1] http://www.efireplacestore.com/fsd-18516.html
Our Answer: This item is a woodburning fireplace insert, only meant for installation into a pre-existing masonry fireplace, not a manufactured unit like your MBU36. From Page: MAJ-WR2500X02 [1] Manufacturer's Product Number: WR2500X02 Our SKU:...
Our Answer: There is a link to the downloadable product manual on the item's description tab above. This will provide you with all the necessary framing dimensions, clearances, and venting guidelines. From Page: CUI-BVP42FP32LN [1] Manufacturer's...
Our Answer: As this is a ventless log set, R.H. Peterson (the manufacturer) does not make the burners available separate from the logs or the pilot assemblies. These ventless sets have to be so meticulously engineered and built that any kind of mixin...
Our Answer: Our gas fireplace inserts utilize what is called a millivolt pilot. This pilot system has a small flame that generates power for the unit's gas valve to operate. As a result, they do not require outside power to operate and can be used in...
Our Answer: Unfortunately, this fireplace cannot be modified for the purpose of lowering the firebox. It is specifically manufactured as it is, with that 6-8" elevation, to be a zero clearance fireplace that can be placed directly on a wood floor (no...
Our Answer: No, unfortunately it only comes in the 6" inner diameter. From Page: CPF-73675 [1] Manufacturer's Product Number: BM0039 Our SKU: BM0039 Page ID: cpf-73675 Links: ------ [1] http://www.efireplacestore.com/cpf-73675.html
Our Answer: This particular unit is rated to heat about 1,200 square feet. This rating will vary, based on ceiling height, climate, and insulation. The unit does have an optional rear heat register, which allows the room directly behind the furnace t...
Our Answer: The blower assembly for this appliance while noticeable should not be loud enough to be disturbing From Page: CPF-93375 [1] Manufacturer's Product Number: FL063 Our SKU: FL063 Page ID: cpf-93375 Links: ------ [1] http://www.efire...
Our Answer: We are indeed a licensed dealer of Osburn products and currently stock the 2400 Insert. From Page: FSD-OB02401 [1] Manufacturer's Product Number: OB02401 Our SKU: OB02401 Page ID: fsd-ob02401 Links: ------ [1] http://www.efirepla...
Our Answer: It is necessary to calibrate the receiver to the remote after the batteries are installed in both the receiver and remote. Simply use a ballpoint pen or toothpick to hold in the small "Learn" button on the front of the receiver. It should...
Our Answer: A blower would indeed increase the heating capability of your fireplace. The appropriate blower for this appliance is Empire's FBB4. This unit can only be operated manually - there is no remote for it. You may view it by following the bel...
Our Answer: This particular unit would indeed need to be framed into a wooden wall enclosure or could be utilized in a wooden mantel cabinet. The unit will come with an installation manual that will detailed the framing dimensions and the required cl...
Our Answer: Unfortunately, no. This is a ceramic fiber brick liner meant for use only in a gas fireplace. It cannot withstand the heat of your wood stove. From Page: CUI-VBP32SA [1] Manufacturer's Product Number: VBP-32-SA Our SKU: VBP-32-SA ...
Our Answer: As long as you thoroughly clean the stainless steel surface and then rough it up with sandpaper, you should have no issues painting this item. These steps simply server to prepare the metal to be painted. From Page: FSD-O36NRRH [1] M...
Our Answer: Any all-purpose cleaner should work just fine on the painted surface of this surround. Only the logs and glass require specialized cleaner. In Response to Question: What can I use on the black metal around the fireplace to make it lo...
Our Answer: Napoleon says this unit's burner pan holds a little less than 2 liters of ethanol when filled to capacity. From Page: NPL-WMFE3 [1] Manufacturer's Product Number: WMFE3K Our SKU: WMFE3K Page ID: npl-wmfe3 Links: ------ [1] http:...
Our Answer: Per your dimensions, this Medium Innsbrook would work just fine. You may check out our Large Innsbrook, as well. It appears you'll have plenty of room for this unit. You'll just want to confirm that your rear width measures at least 22". ...
Our Answer: The fireplace on this page is a direct vent model that requires venting. For a vent-free unit to heat that area, you may be interested in these: Vail Vent-Free Natural Gas Fireplace with Remote Ready Controls - 24 Inch [1] Vantage Hearth ...
Our Answer: While Empire does not offer a specific efficiency rating for this unit, B vent room heaters typically have an efficiency of 50-70%. From Page: CUI-RH65BLP [1] Manufacturer's Product Number: RH-65BLP Our SKU: RH-65BLP Page ID: cui-...
Our Answer: This screen is gray. From Page: FSD-18445 [1] Manufacturer's Product Number: 18445 Our SKU: 18445 Page ID: fsd-18445 Links: ------ [1] http://www.efireplacestore.com/fsd-18445.html
Our Answer: More than likely, this frame will not work for your application. It is specifically designed to snap right onto Empire's 36" Breckenridge fireplace. It's interior dimensions are approximately 39 1/2" wide x 35" high. What is the model of ...
Our Answer: The BGD33NR fireplace does not come with the mantel pictured on its page. The mantel it is pictured with can be found here: Napoleon Princess Small Corner Series Wooden Mantel [1] That mantel is a corner model, and is also available in a ...
Our Answer: The NPL-BGD36CFNTR is a great unit however it's BTU rating is a bit lower than your preferred 24,000. Also, you can add-on a blower but it does not have a louvered front. Additionally, you do have the option to add-on decorative brick pan...
Our Answer: The price listed for the NPL-1101 does not include the H222 door. The H222 Black Arch door is an additional charge listed within the options. From Page: NPL-1100 [1] Manufacturer's Product Number: 1100P-1 Our SKU: 1100P-1 Page ID:...
Our Answer: This manufacturer only offers this surround in the brick red color that is offered. However, we do offer other colors in the surrounds manufactured by Flexi-brick. The surrounds are made of durable polystyrene and can be seen at the links...
Our Answer: This unit, along with our larger capacity models, can be used at high altitude without a problem. They will however, suffer a 6% loss in heating capacity per 1,000 feet of altitude past 4,500 feet. You may want to switch to a slightly lar...
Our Answer: The main difference between these two gaskets is the shape. Our FSD-153 is a standard rope gasket that is round in shape. FSD-VCGG is a griddle gasket that is a little flatter and is generally designated for griddle plates. The price is s...
Our Answer: While it is always best to keep brands of stove pipe and connectors the same, this elbow should connect to any single-wall, crimp type stove pipe. From Page: CPF-73840 [1] Manufacturer's Product Number: 8-24-602C Our SKU: 8-24-602C...
Our Answer: This traditional floor pad base for stone inlays measures 36 1/2" wide by 30 3/13" deep, and it is 7/8" thick. It is for use with the cast stone inlay kits found here: Empire Cast Stone Inlay Kit - For Use with Empire Traditional Floor Pa...
Our Answer: Unfortunately not. Our replacement gasket material must be applied to your stove or fireplace with gasket cement. Something like our AW Perkins Gasket Cement - FSD-80AW, for example. Please check out this product here: AW Perkins Stove Ga...
Our Answer: Unfortunately, these cabinet doors will not fit your DVRT36 unit. They are only for 36" CDV and DVB models. For reference, please see the following link for the required cabinet door frame here: Majestic Designer Black Fireplace Cabinet D...
Our Answer: This grate is 17" wide, approximately 11.5" deep, and it is 5.5" high at the front lip and 7" high at the back lip. From Page: NPL-G17 [1] Manufacturer's Product Number: G17 Our SKU: G17 Page ID: npl-g17 Links: ------ [1] http:/...
Our Answer: Our trim kits simply complete the look of their designated fireplace. The medium trim kits have a flat profile. Our curved trim kits have a rounded finish. Their edges are still square but their fronts curve out into the room. From Page...
Our Answer: No. You may use kerosene fuel only with this item. From Page: UF-C-1137 [1] Manufacturer's Product Number: C-1137 Our SKU: C-1137 Page ID: fsd-c-1137 Links: ------ [1] http://www.efireplacestore.com/fsd-c-1137.html
Our Answer: Unfortunately, this particular stove has not been tested for mantel clearance by Napoleon. The only overhead clearance listed is a minimum of 84 inches from the hearth pad to the ceiling. The closest version of this stove is the 1402 inse...
Our Answer: This unit does require assembly and it does include everything needed to get started except for the fuel. This fire-pit is capable of 40,000 BTU. From Page: UF-GAD860SP [1] Manufacturer's Product Number: GAD860SP Our SKU: GAD860SP ...
Our Answer: If you are utilizing Simpson DuraVent chimney, you can use an adaptor such as this: Dura-Vent PelletVent Pro 4-Inch Chimney Adaptor [1] You would also need to use a chimney adaptor to complete the connection to 6" DuraTech or DuraPlus chi...
Our Answer: Per the manufacturer, they do not rate these rugs to a particular temperature. The only information stated from their technical department is that the rug will stand up to, but not including, exposure to direct flame. Any fallen embers or...
Our Answer: It is only recommended to use this product in a wood burning fire. From Page: RUT-715 [1] Manufacturer's Product Number: 715 Our SKU: 715 Page ID: rut-715 Links: ------ [1] http://www.efireplacestore.com/rut-715.html
Our Answer: Per the manufacturer, this item measures 56 inches wide by 26 inches deep. From Page: ADC-H-60 [1] Manufacturer's Product Number: H-60 Our SKU: H-60 Page ID: adc-h-60 Links: ------ [1] http://www.efireplacestore.com/adc-h-60.html...
Our Answer: Unfortunately, we do not have the exact dimensions available for this unit. It is designed to be a specific ft for various Monessen appliances. If you'd like to reply with your fireplace's model number, we'd be happy to search for a compa...
Our Answer: This blower features a CFM of 105. From Page: NPL-GZ550-1KT [1] Manufacturer's Product Number: GZ550-1KT Our SKU: GZ550-1KT Page ID: npl-gz550-1kt Links: ------ [1] http://www.efireplacestore.com/npl-gz550-1kt.html
Our Answer: You are correct. We are prohibited from shipping any Napoleon item to a Canadian customer. This is a rule imposed by Napoleon as a Canadian manufacturer. From Page: NPL-F60 [1] Manufacturer's Product Number: F60 Our SKU: F60 Page...
Our Answer: Yes. This paint will adhere perfectly fine to concrete block. Keep in mind that multiple light coats will provide better results than a few heavy layers. From Page: FSD-92G [1] Manufacturer's Product Number: 92G Our SKU: 92G Page ...
Our Answer: This outside air kit must be routed to the base of the stove pedestal, which has a metal knockout that can be removed and allow the fresh air kit to be attached. Unfortunately, the kit is only available for free standing pedestal models a...
Our Answer: Please see these instructions (re: changing display from Fahrenheit to Celcius and vice versa): The factory setting for temperature is F. To change this setting to C, first press and hold the UP button and the DOWN button on the transmitt...
Our Answer: Generally, it is the other way around. Cast iron grates can last for quite some time, if they are a good quality. Many grates that are cast nowadays are very porous in nature and fail quickly. A good quality cast iron grate can withstand ...
Our Answer: Per the manufacturer, the base width of this set is just under 8". From Page: ADC-830942 [1] Manufacturer's Product Number: X830942 Our SKU: X830942 Page ID: adc-830942 Links: ------ [1] http://www.efireplacestore.com/adc-830942....
Our Answer: This item should work for your repair. It is designed to repair either masonry or metal. Ideally, it is used to repair small cracks similar to those that occur between fire bricks. You may also check out the below furnace cement. It effec...
Our Answer: According to the manufacturer, the base of this set measures approximately 10" x 6". The sizing can vary between batches, but should be within about 1/2" of this measurement. From Page: ADC-820946 [1] Manufacturer's Product Number: X8...
Our Answer: Yes, the package for this item will have the model information printed on it, so it will be apparent what the item is. Unfortunately, we do not offer a gift wrap option on this item at this time. Also, please note there is some assembly r...
Our Answer: This particular stove can be used as a direct vent model or modified to work as a B-vent unit. Because of your space limitations for venting, I would definitely go with the B-vent setup for this unit. I'm assuming the 6" whole you have in...
Our Answer: Firstly, per your dimensions, I would recommend a 30" log set. Even with the pilot assembly that you are interested in, a 30" set will fit just fine. The coals are hard to judge, though. Peterson is not so good as to provide a reference c...
Our Answer: You can indeed vent this unit through concrete. You'll simply have to drill a hole through to the outside. From Page: NPL-BGD36CFNTR [1] Manufacturer's Product Number: BGD36CFNTR Our SKU: BGD36CFNTR Page ID: npl-bgd36cfntr Links...
Our Answer: These units are relatively easy to install. You'll simply need to provide a fuel supply to the box and run a venting system. Since you have a wood burning fireplace, the venting run will be as easy as dropping a flex liner down your exist...
Our Answer: You would only need to add the pedestal base. The ash pan kit is solely an accessory. The ash pan base does require the pedestal base though. From Page: NPL-EP20PAD [1] Manufacturer's Product Number: EP20PAD Our SKU: EP20PAD Page...
Our Answer: The support legs that come with this fire back have numerous slots cut into them that allow you to position the fire back at different angles. Any of the slots can be used and it is personal preference as to what angle you would like the ...
Our Answer: Yes, the price on this item page is for one 12 oz. spray can of the Copperfield Pewter Gas Fireplace Surround Paint. From Page: CPF-43407 [1] Manufacturer's Product Number: 6321 Our SKU: 6321 Page ID: cpf-43407 Links: ------ [1] ...
Our Answer: You'll want to use the anchor plate designed for SuperPro pipe. Please find it here: SuperPro All-Fuel Fireplace Adaptor Plate with Stainless Steel Collar - For Chimney Pipes with a 6-Inch Inner Diameter [1] From Page: CPF-70677 [2] M...
Our Answer: This fireplace does take advantage of double wall pipe. We have varying lengths available, from 12" to 48". Please follow the below link. Once on the page, filter your search by selecting "FMI" as the brand and "8" as the size. Class A Ch...
Our Answer: This unit only measures 24" in diameter. So, it would only hold approximately 12-15 split logs. From Page: CPF-61050 [1] Manufacturer's Product Number: 61050 Our SKU: 61050 Page ID: cpf-61050 Links: ------ [1] http://www.efirepl...
Our Answer: Unfortunately, the item you inquired about is the closest riser bar we have to what you need. However, this item is made only for the 39" Portland Traditional II glass doors and we cannot guarantee it will work with your door. The dimensi...
Our Answer: Unfortunately, this manufacturer only makes these units in a gel fuel or electric setup. Due to the compact size of the firebox and the large amount of wood used in the cabinet surround, it would not be feasible to use a gas firebox in th...
Our Answer: Replacing these panels is fairly straight-forward. You would simply need to disconnect the attachment rod from your fireplace, slide the old panels off, then slide these new panels into place. Removal of the attachment rod will vary from ...
Our Answer: If you have a vented burner assembly, yes. If you have a vent-free (unvented) unit, no. This product is not suitable for use with a vent-free appliance. From Page: PTS-EM-1 [1] Manufacturer's Product Number: EM-1 Our SKU: EM-1 Pa...
Our Answer: "Surface mount" refers to the method of hanging this and other fireplace hoods. With a surface mount model, you will be anchoring your hood horizontally into the area above your firebox, as opposed to a "lintel mount," where the hood is m...
Our Answer: The width measurement of this door's glass panel is 15 1/2". The top is slightly arched with the highest point in the center. The center height measurement is 9 3/4". From Page: NPL-EPI-1101P-DEAL [1] Manufacturer's Product Number: E...
Our Answer: Type 1 and Type 2 are both referring to the UL1618 code, which covers wall protectors, floor protectors, and hearth extensions that are intended for use with heat producing devices, such as fireplaces, fireplace stoves, fireplace inserts,...
Our Answer: It is never recommended to use a pipe size with less diameter than your appliance's opening. You should try to use 6" pipe if at all possible. We have 6" stovepipe, class A chimney pipe and chimney liner from a few different manufacturers...
Our Answer: We do have some vent-free coal baskets. Please this link: Victorian Hearth Fireplace Inserts [1] Once here, look on the left-hand side and under the "Vent Type" section select "Vent-Free". Then you will see our selection of vent-free bask...
Our Answer: Monessen has informed us that the valve part number you provided has been replaced by part #27D8951. We can get this part for you. If you want to order this valve, please call us at 1-800-203-1642. In Response to Question: I have a M...
Our Answer: That is correct. These are indeed screen doors. From Page: CPF-61235 [1] Manufacturer's Product Number: 61235 Our SKU: 61235 Page ID: cpf-61235 Links: ------ [1] http://www.efireplacestore.com/cpf-61235.html
Our Answer: Per the manufacturer, the listed steady state efficiency rating for this appliance is 67%. The outer casing will be hot to the touch, but does not get hot enough to cause burns in most areas. The outflow louvers on the top and top sides o...
Our Answer: While we do stock Maxitrol regulators, they are threaded for 1/2" NPT inputs and ouputs. However, an increaser and reducer could be used to make the connection. Do you know the gas pressure the appliance requires? Please advise at your co...
Our Answer: Please see our full return policy for detailed information: Return Policy [1] In Response to Question: I purchased a rug 100% wool with border trim like your rug. Unfortunately, the border was glued in not dyed and when vacuumed, the ...
Our Answer: Any non-volatile, flammable fluid - like kerosene - is an ideal fuel. From Page: CPF-61098 [1] Manufacturer's Product Number: 61098 Our SKU: 61098 Page ID: cpf-61098 Links: ------ [1] http://www.efireplacestore.com/cpf-61098.htm...
Our Answer: This unit only offers grey herringbone or vintage brown as color options. We apologize, but red is not currently available. From Page: MAJ-36MCUFD-R [1] Manufacturer's Product Number: 36MCUFD-R Our SKU: 36MCUFD-R Page ID: maj-36mc...
Our Answer: I'm sorry, but we do not have a picture of this item. These doors are intended for use only with corner-style Vantage Hearth woodburning fireplaces. From Page: CUI-DC36L-R-LS-RS [1] Manufacturer's Product Number: DC36L/R/LS/RS Our S...
Our Answer: While this grate does not meet your needs, please see this one: UniFlame 30 Inch Steel Fireplace Grate [1] Please note, while it is not listed on the page, the manufacturer has informed me that the UF-C-1536 grate has a 6" clearance (dist...
Our Answer: Unfortunately, this photo does not give the best representation of the finish on this unit. It is actually a brushed stainless finish, as are most outdoor models. This is necessary to prevent corrosion. This unit would require a 53" by 53...
Our Answer: This firebox does not include the brick liner or the burner assembly. It is simply a firebox. You may find its available brick liners by following the Accessories tab. From Page: CUI-VFD42FB0L [1] Manufacturer's Product Number: VFD-4...
Our Answer: Roof pitch is only needed for flashings that are installed on the roof itself, as there are a few different flashings available. These cathedral ceiling support boxes are made to be installed into ceilings of any pitch. They are available...
Our Answer: These fireplaces are basically the same. They are manufactured on the same platform. They are simply finished out by different manufacturers. The FSD-368ST Windsor is one onto itself. There are only a few options available for it. However...
Our Answer: According to the manufacturer, the other predominant colors in this rug are beige and a dark hunter green. From Page: CPF-61144 [1] Manufacturer's Product Number: 61144 Our SKU: 61144 Page ID: cpf-61144 Links: ------ [1] http://w...
Our Answer: Per the manufacturer, the depth of this grate is approximately 17-18" deep, depending on the casting. From Page: UF-C-1552 [1] Manufacturer's Product Number: C-1552 Our SKU: C-1552 Page ID: uf-c-1552 Links: ------ [1] http://www....
Our Answer: When doing this kind of conversion, you would need the following products: Simpson DuraLiner Slip Connector and Hanger for Dura liner 6 inch Pipe [1] DuraTech All-Fuel Masonry Chimney DuraLiner Transition Plate - For Chimney Pipes with a ...
Our Answer: While this cap can technically be used with gas logs, it is not recommended. Like other top mounted dampers, there is still the risk of carbon monoxide backing up into the house if the damper is closed during operation. If you choose to i...
Our Answer: It will not unfortunately, as this is a product manufactured by Security Chimneys and Supervent is a Selkirk product. However, we do carry the Superpro line that is also made by Selkirk and is interchangeable with your product. The Superp...
Our Answer: Unfortunately, we do not have an installation video for this item. The blower will come with detailed installation instructions. Please note this item is only use with the following Monessen appliances: BLDV Belmont Direct Vent Gas Firepl...
Our Answer: On this particular burner setup, you can most certainly remove the burner end cap from the left hand side and swap the gas input onto that end if needed. From Page: PTS-G45-GL24Z-NONEN [1] Manufacturer's Product Number: G45-GL24Z-NONE...
Our Answer: This item features vinyl and not leather. From Page: UF-C-6162 [1] Manufacturer's Product Number: C-6162 Our SKU: C-6162 Page ID: uf-c-6162 Links: ------ [1] http://www.efireplacestore.com/uf-c-6162.html
Our Answer: That all depends on your Hampton Stove. If your unit is vent free, then we would have to recommend that you do not use these embers. However, if it is a vented appliance, then we would suggest you review your owner's manual for any notati...
Our Answer: It would not hinder natural draft as long as the cap is matched appropriately to your appliance. For example, this cap has a cross-sectional area of 28.3 square inches. As long as this is sufficient for your fireplace, it will work just f...
Our Answer: This firebox is sold individually, without a log set. Most vent free log sets that are sized to fit this box will have a BTU output in the range of 35K to 40K. Please let me know if I can assist you in choosing a log set to fit this box. ...
Our Answer: This particular hood cannot be used with glass doors installed. In order to use a hood with this installation, you would need to use a "glass enclosure" type of hood, such as this: Elite Glass Enclosure Fireplace Hood with Surface Mount -...
Our Answer: These flex pipes are generally designed for relining purposes or for working around obstacles. However, This pipe can indeed be used to bridge the gap between your tee and the remainder of your vent pipe. This pipe should only be used ind...
Our Answer: While we may have something that will work for you, the FSD-BKT is designed specifically for use with Chateau and Tudor Fireplaces. All of our blowers operate in basically the same way. The difference lies in the size and mounting of them...
Our Answer: This is a vent free appliance. Please be sure to review the complete users manual posted on this item page. This manual provides information about the safe operation of this vent free appliance. From Page: FSD-ANFC-C [1] Manufacturer'...
Our Answer: You may want to try some of our stove paint for such a finish. Please see this item: Stove Bright Flat Black Paint [1] This is available in 12 oz. spray cans, and it may take 2-4 cans to completely paint your stove. From Page: RUT-70 [...
Our Answer: Yes, this fireplace does have a couple of options for doors. Here are links to each of the bi-fold door options you have with the VB421: Black FMI 42 Inch Extruded Aluminum Bi-Fold Doors - Black [1] Brushed Brass FMI 42 Inch Extruded Alum...
Our Answer: This overlay is roughly 9" from top to bottom at it's center and 20 1/4" in width. This overlay is necessary to complete the door on the Osburn 1500 stove. We cannot guarantee that it will install to any other model of stove, as it is spe...
Our Answer: Unfortunately, Majestic was purchased by Monessen Hearth Systems and has since discontinued production of all parts for this particular unit. I have checked with several of my suppliers, but this conversion kit is not carried by any of th...
Our Answer: In terms of heating, the general rule for indoor applications is 35 BTU per square foot. If we apply this rule to your deck and refer to the NPL-GPF's ability to produce 60,000 BTU, we can assume that this heater is suitable as long as yo...
Our Answer: If you are planning to use this as a rear-vent fireplace and go horizontally through-the-wall, the GD7RVK is indeed an appropriate vent kit. We do have it on our website, please see the following link: Napoleon 20 Inch Flexible Rear Vent ...
Our Answer: The mantel is not included in the price for the Napoleon BGD34NT Direct Top Vent Gas Fireplace. The mantel is available separately and is available in flat, flush and corner models. The one pictured with the BGD34NT is the corner model, w...
Our Answer: Unfortunately, horizontal installation can run into this issue and it can be difficult to correct. The main issue is trying to determine when the leak occurs. If it occurs every time it rains, you will most likely need some sort of rain g...
Our Answer: The following item is a good product for cleaning vertical surfaces in most models of fireplace: Rutland August West Clean and Brite Cleaner - 16 Ounce Spray Bottle [1] This will be sufficient to remove any soot that has built up on your ...
Our Answer: These inserts by Osburn carry a Limited Lifetime Warranty. From Page: FSD-OB02401 [1] Manufacturer's Product Number: OB02401 Our SKU: OB02401 Page ID: fsd-ob02401 Links: ------ [1] http://www.efireplacestore.com/fsd-ob02401.html...
Our Answer: We currently only carry glass door inserts for the Majestic Biltmore. However, we do have screen panels available that also feature doors. Please follow the below link to view an example: Black Fireplace Screen [1] From Page: MAJ-GDB54...
Our Answer: This surround is designed specifically to fit a Napoleon GDI-30 fireplace. It's outside dimension is 42"W x 25"H. It's inside dimensions are approximately 30" W x 21 3/4" H. From Page: NPL-GI-30K [1] Manufacturer's Product Number: GI-...
Our Answer: This adaptor is designed to be installed horizontally into a masonry flue. The smooth end should insert just enough to be flush with the inside surface of your masonry flue. Your black double wall pipe would then attach to the short side ...
Our Answer: This item is meant only for use as a means of bringing in outside air for combustion with a Monessen fireplace. (Also, please note that this item is a carton of 12, not just 1.) In Response to Question: I have a chimney that I have ha...
Our Answer: This unit will be a bit too large for your application. It requires a finished opening of 34 7/16" wide by 32 1/4" tall. Our Vent-Free Innsbrook, found below, would fit well in your fireplace and the included surround would cover your fir...
Our Answer: All of our FMI appliances require the use of FMI specific venting components. You may find an example here: FMI Wood Fireplace 8-in. Diameter Chimney Venting Pipe for FMI Woodburning Fireplaces - 48-in. Length [1] From Page: FSD-B42 [2]...
Our Answer: Yes, please see the following link for the propane version of this fireplace: Empire Tahoe Premium Direct Vent Propane Peninsula Fireplace - 36 Inch [1] From Page: CUI-DVP36PP32EN [2] Manufacturer's Product Number: DVP-36-PP32EN Our...
Our Answer: The tempered glass front will be one large solid pane of glass that spans the entire front height and width of the fireplace. The border around the viewing area of the fireplace opening, behind the glass, will be black in color. The black...
Our Answer: The dimensions of this product are 9"H x 14"W X 21"L. Unfortunately, I don't believe this basket will work for your setup. From Page: ADC-800052 [1] Manufacturer's Product Number: X800052 Our SKU: X800052 Page ID: adc-800052 Lin...
Our Answer: You have two options for surrounds on this insert, both listed in the "Accessories" tab. The smaller faceplate measures 33" H x 43" W and can be found here: Monessen Small Black Fireplace Insert Faceplate - For DIS33 Vent Free Gas Firepla...
Our Answer: This adaptor does work to transition to 8" pipe on the round end. However, it is designed to work specifically with Vermont Castings stoves. It's oval opening measures approximately 5 3/8 x 9 3/4. From Page: CPF-69195 [1] Manufacture...
Our Answer: This liner is only for use with 32" Tahoe Deluxe fireplaces, and it does have all three panels--the back and both sides. From Page: CUI-DVP1SA [1] Manufacturer's Product Number: DVP-1-SA Our SKU: DVP-1-SA Page ID: cui-dvp1sa Lin...
Our Answer: The current sale price listed on the page is for a 12" section. You can choose different lengths by using the drop-down menu above the "Add to Cart" button. The additional cost for each options will be noted in the parenthesis. Options fo...
Our Answer: We do indeed carry fireback boots. These boots aid in supporting and stabilizing your new fireback. They also raise your fireback to allow it to be visible above your fireplace grate. Please follow the below links to check out our options...
Our Answer: The stock photo for this item does indeed show the assembly with polished brass trim. However, the assembly will arrive with the satin black trim indicated in the item description. From Page: FSD-9100-4221-09 [1] Manufacturer's Produc...
Our Answer: Installation costs depend largely on the amount of labor time for your project and current rates in your area. In order to get an accurate quote, it will be necessary to contact reputable mechanical contractors in your area. Most HVAC or ...
Our Answer: While it is possible that this firebox can accept a ceramic or refractory liner, I was not able to find any information for this model. Do you happen to have the owner's manual for this unit? If this fireplace cannot use a liner, the othe...
Our Answer: Unfortunately, no. The FMI 12" piping has an outer wall that is nearly 1.5" larger than the Duratech piping that this anchor plate is intended for. However, FMI appliances that use the 12" diameter piping will already come equipped with a...
Our Answer: Thank you for your patience. This item measures 10" wide by 7" deep. From Page: FSD-18041 [1] Manufacturer's Product Number: 18041 Our SKU: 18041 Page ID: fsd-18041 Links: ------ [1] http://www.efireplacestore.com/fsd-18041.html...
Our Answer: This particular item is designed to be attached to the lintel of an open faced, wood burning fireplace. For an installation with glass doors, I recommend the following type of hood: Elite Glass Enclosure Fireplace Hood with Surface Mount ...
Our Answer: We do offer a canvas lined holder with a bronze finish. Please follow the below link. UniFlame Bronze Wrought Iron Log Rack with Canvas Carrier [1] Uniflame and Woodfield are two different manufacturers for the items that we carry. Fro...
Our Answer: This sort of request will fall to the parts department for U.S. Stove/Vogelzang. Because they will only sell these individual components directly, I recommend contacting them at 1-800-750-2723. From Page: VGL-BK100E [1] Manufacturer's...
Our Answer: This tool set is manufactured of black steel. It is not wrought iron. From Page: UF-W-1246 [1] Manufacturer's Product Number: W-1246 Our SKU: W-1246 Page ID: fsd-w-1246 Links: ------ [1] http://www.efireplacestore.com/fsd-w-1246...
Our Answer: All of our flashing kits are designed to work specifically with certain fireplaces or inserts. We currently do not offer a universal fit flashing kit. If you'd like to reply with the make and model of your insert, we may be able to find a...
Our Answer: That all depends on the size of your Heatilator. This insert requires a minimum fireplace opening of 16 1/2 inches to 21 inches deep x 28 1/2 inches wide x 21 1/2 inches high. We recommend that you confirm that your fireplace can accept a...
Our Answer: These doors will measure approximately 40" wide x 24 3/8" tall x 3/4" deep. These are made specifically for the 42" Loft Outdoor fireplace and we cannot guarantee that they will attach to any other model, as they are engineered for use wi...
Our Answer: Unfortunately, we do not currently have an ETA on when this item will be available again. Please enter your email address on this page and you will be notified when it is back in stock. From Page: UF-S-1084 [1] Manufacturer's Product...
Our Answer: Both types have advantages and drawbacks. A stainless steel fireback is more effective at radiating heat into the room while the fire is burning, but does not offer any heat after the fire has gone out. They are also thinner and can warp ...
Our Answer: We carry one that might work. It is called the Import 3 Fold Stainless Steel Fireplace Screen [1]. It is stainless steel and is much more likely to resist salt air than any of the others. In Response to Question: I would like to know...
Our Answer: No, this item is only a surround for a fireplace insert that you slide into an existing fireplace. This surround is compatible with this insert: Innsbrook Medium Direct Vent Gas Fireplace Insert - Natural Gas [1] From Page: CUI-S336BL ...
Our Answer: The primary reason gas fireplaces are not used in manufactured entertainment centers is due to clearances. The electric models produce a fraction of the BTU output and as a result, can be made into an entertainment center relatively easil...
Our Answer: This product is intended primarily to bond sheet metal and masonry products to one another in high temperature situations. I cannot recommend it for glass. From Page: CPF-29525 [1] Manufacturer's Product Number: 1612B Our SKU: 1612B...
Our Answer: Yes, there is a 4" inner diameter for the exhaust included with this 7" outer diameter direct vent pipe. Please note this pipe is only tested and listed for use with Napoleon direct vent stoves. From Page: NPL-BM6745 [1] Manufacturer...
Our Answer: No, this river rock kit cannot replace the glass pebbles within the Luminary Linear Vent-Free Gas Fireplace [1]. That vent-free unit only accepts alternate glass color options; unfortunately, there is no river rock kit available for it at...
Our Answer: After checking with the manufacturer, we have been advised that while the 5053103 part number is correct for this unit, this hood has been discontinued for quite some time. Currently, there are no direct fit replacements for this unit. It...
Our Answer: While it is possible these bi-fold doors would fit your unit properly, I cannot say for sure. These doors are manufactured for specific models of FMI and Vantage Hearth (Vanguard) fireplaces, as well as older DESA units. There should be a...
Our Answer: No, this vent-free stove cannot be converted to a direct unit. Empire does make the Heritage stove in a separate direct vent model; please see below: Empire DVP30CA30 Heritage Direct Vent Cast Iron Gas Stove with Porcelain Finish - Natura...
Our Answer: We do indeed have the Porcelain Mahogany Heritage vent-free stove, please see the following link: Porcelain Mahogany Heritage Vent-Free Stove [1] Please note that is the propane model; the same stove is also available in natural gas. F...
Our Answer: The listed price is for the fireplace only and excludes any mantel cost. This unit is a rear vent model that can be installed flat against an outside wall with an external wall termination. The mantel shown in the photo can be viewed here...
Our Answer: This item takes advantage of a chemical reaction to loosen soot in dirty chimneys. To use, simply sprinkle 1/4 cup of Soot Remover onto a low fire or hot coals, then increase the fire and burn briskly for 30 minutes. From Page: FSD-201...
Our Answer: Based on your provided dimensions, this draft hood adapter will be what is needed to start your b-vent piping system. We can only guarantee that this connector will work with other Simpson Dura-vent b-vent components. From Page: CPF-684...
Our Answer: Unfortunately, no such accessory is available for Osburn's 2400. From Page: FSD-OA10100 [1] Manufacturer's Product Number: OA10100 Our SKU: OA10100 Page ID: fsd-oa10100 Links: ------ [1] http://www.efireplacestore.com/fsd-oa1010...
Our Answer: Yes, the 1100C is going to be much more than you need, as most of our stoves will be for that size of room. Here is a stove that is a nice, smaller alternative: Timberwolf 2100 Economizer EPA Wood Burning Stove [1] In Response to Quest...
Our Answer: The general difference between Napoleon's BGD and GD models is overall efficiency and BTU output. The GD models are going to have higher efficiency ratings and generate more BTUs. From Page: NPL-BGD33NR [1] Manufacturer's Product Num...
Our Answer: The mantel in this picture (found here [1]) has a top length of 64.5" and a bottom length of 54.5". The comparable small mantels manufactured by Napoleon (like the Bonaparte mantel, found here [2]) have the same dimensions. These are the ...
Our Answer: These doors will only work with the FMI Georgian 42" fireplace. You can see that fireplace here: FMI Georgian 42 Inch Smooth Faced Woodburning Fireplace [1] From Page: FSD-BDG42 [2] Manufacturer's Product Number: BDG42 Our SKU: BDG4...
Our Answer: This product is actually designed for insulating flexible fireplace liners, however there would not be an issue with using it to insulate a furnace flue. The b-vent pipe that is typically used to vent a furnace is thicker than a liner, bu...
Our Answer: This stove is approved for use in mobile homes when used with a separately purchased Fresh Air Kit. Please see the fresh air kit you would need at the following link: US Stove 69FAK Fresh Air Kit [1] For more information on mobile home in...
Our Answer: This unit requires a door overlay, a faceplate shroud and a shroud trim kit for installation. All of these items are listed in the "Accessories" tab next to the "Item Description." The door overlay and shroud trim are both available in bl...
Our Answer: This item is designed to attach to the front of an Al Fresco vent-free fireplace. You'd be interested in one of our vinyl siding stand-offs. Please follow the below link to view one of our options. Please note that these units are brand s...
Our Answer: In order to start a stovepipe installation, you will first need an appliance adaptor. This acts as the starting collar for the stovepipe and mates it to the stove. You will then proceed with as much rigid pipe as needed, until you get wit...
Our Answer: Unfortunately, these logs are not designed to be used in a Heat N Glo manufactured fireplace. They are designed specifically for use in a masonry fireplace and are not manufactured from the same material. The logs you need are a lightweig...
Our Answer: Unfortunately, our options that fit these criteria are limited. Please follow the below links for some examples. Vail 20,000 BTU Vent-Free Propane Fireplace - 26 Inch [1] Vantage Hearth Mini Classic Hearth VGMR Vent-Free Compact Propane F...
Our Answer: Those terms simply refer the position of the cap of your venting system. If your termination cap is coming out of a wall, you then have a horizontal termination. If you have more of a traditional chimney that extends through your roof, th...
Our Answer: It is indeed most common to use a cast iron boot to achieve the installation you are working on, but as you mention, vertical height will prevent the use of a boot. I am not aware of an adapter that is currently manufactured that would be...
Our Answer: This 10 lb bag should be ideal for your fireplace. From Page: FSD-AFF-COPRF-10 [1] Manufacturer's Product Number: AFF-COPRF-10 Our SKU: AFF-COPRF-10 Page ID: fsd-aff-coprf-10 Links: ------ [1] http://www.efireplacestore.com/fsd-...
Our Answer: On most stoves, this adapter will be required: Dura-Black Welded Steel Stovepipe to Appliance Adaptor - 6-Inch Diameter [1] Due to the fact that the stovepipe is welded, rather than crimped, most stoves are just far enough off that the pi...
Our Answer: In order to complete this repair, you would need a complete damper throat and plate. We sell these products in varying sizes for different fireboxes, but the most commonly sold size can be seen here: Vestal 36 Inch Cast Iron Throat-Style ...
Our Answer: Unfortunately, not. This unit is designed to burn coal only. From Page: USS-BCAC [1] Manufacturer's Product Number: BCAC Our SKU: BCAC Page ID: uss-bcac Links: ------ [1] http://www.efireplacestore.com/uss-bcac.html
Our Answer: These grates are indeed manufactured in the US by the HY-C company. From Page: HYC-G27 [1] Manufacturer's Product Number: G27 Our SKU: G27 Page ID: hyc-g27 Links: ------ [1] http://www.efireplacestore.com/hyc-g27.html
Our Answer: You are correct that this will work for your application. The paint will require a short time to heat cure, but should dry to a smooth, easy to clean finish once cured. Two or three cans of paint should work just fine to cover your Dovre ...
Our Answer: We do not have any electric units that can be placed onto a table and most must be recessed into a wall. However, you may be interested in our electric stoves. Please follow the below link to view one of these. Fire Sense Stowe Electric S...
Our Answer: These gloves have an overall length of about 14". They are a universal fit and should be large enough for your needs. From Page: CPF-74100 [1] Manufacturer's Product Number: 7900 Our SKU: 7900 Page ID: cpf-74100 Links: ------ [1...
Our Answer: Many of those heaters cannot be converted. Do you know the model number or manufacturer of your heater? We'd be happy to check our conversion kits for you. In Response to Question: I have a vent free pedestal heater my parents gave m...
Our Answer: Yes, there would be no problem mounting the FA5807 to the wall beneath your arched mantel. From Page: SEI-FA5807 [1] Manufacturer's Product Number: 37-237-058-4-01 Our SKU: 37-237-058-4-01 Page ID: sei-fa5807 Links: ------ [1] h...
Our Answer: The vast majority of our replacement ceramic liners are designated for specific fireplaces. For example, our CUI-VBP32SE that you are interested in is meant to only be used with 32 Inch Breckenridge Deluxe Fireboxes. The best way to make ...
Our Answer: Ceramic liners, such as this product, usually measure between 3/8" to 1/2". Refractory liners are thicker and will measure from 1/2" to 1". Refractory liners are standard in wood burning units and are designed to take more abuse. From P...
Our Answer: It is not required to have a mixing chamber with a natural gas log lighter, like it is with a LP lighter like this item. We sell natural gas log lighters both with and without mixing chambers. A mixing chamber would only be needed if you ...
Our Answer: The distance from the center of the vertical opening to the outside edge of the horizontal opening is 7 1/2" for this 6" 90 degree elbow. Your pipe connections will overlap by about 1 14". From Page: CPF-6912-DVL6ELB [1] Manufacturer...
Our Answer: I agree with you. This would definitely be able to sit on the existing brick corbels, assuming they are relatively level with one another. In Response to Question: I have a brick fireplace with built in corbels; bricks that protrude, ...
Our Answer: In a word, yes. Thoroughly cleaning and lightly sanding the cap prior to painting will help ensure an even and effective paint job. From Page: CPF-13115 [1] Manufacturer's Product Number: 13115 Our SKU: 13115 Page ID: cpf-13115 ...
Our Answer: Yes, we have this same cap in copper, please see this link: Draft King 9 in. x 9 in. Copper Single Flue Chimney Cover [1] From Page: HYC-CBC99 [2] Manufacturer's Product Number: CBC99 Our SKU: CBC99 Page ID: hyc-cbc99 Links: ----...
Our Answer: Empire does not provide those exact underside dimensions, but you are looking at approximately 68" lookout width and 3-4" lookout depth. From Page: CUI-MS72UH [1] Manufacturer's Product Number: MS-72-UH Our SKU: MS-72-UH Page ID:...
Our Answer: Unfortunately, these cabinets are only meant to accept electric fireplaces. While the bottom and sides of a vent-free unit like this Vail wouldn't be an issue, the standoffs inside that cabinet above the roof of the firebox will not be su...
Our Answer: Yes, the Copperfield 60F is an excellent choice for rigidity (.480" Fiberglass Rod) and value. From Page: CPF-236-60F [1] Manufacturer's Product Number: 60-X-32 Our SKU: 60-X-32 Page ID: cpf-236-60f Links: ------ [1] http://www....
Our Answer: This item is not the access door itself, but rather the insulation kit for the 8" x 12" Woodfield cast iron access doors. Please see this link for that door: Woodfield Cast Iron Access Door - 8 Inch x 12 Inch [1] This door is cast iron, w...
Our Answer: This stove has one secondary air tube. It has a 1.8 cubic foot firebox, which will put burn time between 6-8 hours. From Page: SBI-DB03120 [1] Manufacturer's Product Number: DB03120 Our SKU: DB03120 Page ID: sbi-db03120 Links: -...
Our Answer: I'm sorry, we only ship to the United States and Canada. From Page: UF-S9668 [1] Manufacturer's Product Number: S-9668 Our SKU: S-9668 Page ID: 3focasobrsc Links: ------ [1] http://www.efireplacestore.com/3focasobrsc.html
Our Answer: Unfortunately, I will not have a way of knowing if this paint would be an exact match. In order to be certain, a paint code would need to be matched up. You may contact the Forrest Paint Company, maker of Stovebright paints. The phone num...
Our Answer: This product would definitely be suitable for this application. The link for the paint is here: Patriot Blue Stovebright Stove Paint [1] Also, to answer your other prep question, it would only be necessary to sand off any surface rust, th...
Our Answer: Circulating fireboxes have the ability to pull in room air, heat it and return it to the room either passively or with the assistance of a blower. This is accomplished through the louvres above and below the firebox opening. Non-circulati...
Our Answer: This unit weights approximately 225 lbs. From Page: CUI-V3612ST [1] Manufacturer's Product Number: V3612ST Our SKU: V3612ST Page ID: cui-v3612st Links: ------ [1] http://www.efireplacestore.com/cui-v3612st.html
Our Answer: That depends on your roof pitch. If your roof pitch is 0/12 to 6/12, a minimum distance of 12" is required between the shingles and the termination. For steeper roofs with pitches from 6/12 to 12/12, you must maintain a height of 15" In...
Our Answer: Unfortunately, we do not list the specific dimensions for this item. It is designed to be used specifically with Empire fireplaces. From Page: CUI-DVG1L [1] Manufacturer's Product Number: DVG-1-LBL Our SKU: DVG-1-LBL Page ID: cui...
Our Answer: Yes, Napoleon's HD series (which includes this unit, the HD35 and the HD46) all feature a built-in adjustable flame/heat control. The hi-lo knob (manual control only) allows for 43% adjust-ability of the flame on these units. From Page...
Our Answer: As you face the burner in the fireplace, the gas inlet and valve for this burner assembly are located on the right hand side. From Page: FSD-C9B-SE-N [1] Manufacturer's Product Number: C9B-SE-N Our SKU: C9B-SE-N Page ID: fsd-c9b-s...
Our Answer: While there are a couple versions of the solid mesh, Old World screens that are slightly wider, this model is only available in the 42" width currently. From Page: FSD-18474 [1] Manufacturer's Product Number: 18474 Our SKU: 18474 ...
Our Answer: Vermiculite is designed to be a burner medium for propane fueled burner pans. Vermiculite should completely fill the burner pan - level to the top. Ember Glow is then scattered on top of the vermiculite to produce the glowing effect. Fr...
Our Answer: Most of the hearth rugs we offer do indeed have a latex backing applied, however the wool rugs use a jute backing instead. The only other material difference is with the fiberglass "guardian" rugs, which utilize a vinyl backing. From Pa...
Our Answer: This log holder is not made of wrought iron. It is manufactured of standard steel. We do indeed offer a collection of wrought iron items, though. A quick search of "wrought iron log holders" will display our options. From Page: NPL-LH4...
Our Answer: The Napoleon GI3600 gas insert comes directly from the manufacturer with a built in GZ552 blower system. This is a slightly smaller, wider version of the item in question. Generally, replacement parts can be ordered to replace any defecti...
Our Answer: While we do offer many vent free fireplaces that are narrower than 35", none of them meet that criteria with an included mantel. Perhaps, you'd be interested in one of our smaller Vail units like the below 26" unit. You could then have a ...
Our Answer: While this unit only comes in black, there is a stainless steel face available for it. Please follow the below link to find this product. Monessen Hand-Brushed Stainless Steel Curved Fireplace Face - For 42 Inch Monessen Serenade Wide Vie...
Our Answer: Unfortunately, Monessen has recently discontinued the brass trim kit, due to lack of demand. The unit is only available with the black or stainless steel trim kits that they still manufacture. I apologize for any inconvenience. From Pag...
Our Answer: The entire Breckenridge line will be a vent free firebox only. A vent free log set of appropriate size must be added. This particular model does come with a herringbone liner as standard, but a blower is not available on the Breckenridge ...
Our Answer: This particular unit does not feature an ash drawer. Ashes must be removed through the door after burn down. The unit does have a front mounted ash lip to help prevent spillage. If the unit is installed using a properly sized 6 inch chimn...
Our Answer: The picture of this MCUF firebox does indeed feature the optional arched front, and the optional cabinet frame and optional doors. We have all of these items in stock, please see the following links: Monessen 36 Inch Black Texture Arched ...
Our Answer: We're sorry, but no, these doors are only for use with select FMI 42" fireplaces. From Page: FSD-BD42 [1] Manufacturer's Product Number: BD42 Our SKU: BD42 Page ID: fsd-bd42 Links: ------ [1] http://www.efireplacestore.com/fsd-bd...
Our Answer: To install this insert and use a masonry chimney for venting you will need the following components: HomeSaver UltraPro Tee with 3 inch Take-Off for 4 inch Chimney Liner [1] 4 inch x 25-ft. HomeSaver Ultrapro 316Ti Chimney Re-Liner Pipe [...
Our Answer: We have a variety of both vent-free and direct vent inserts on our site. You can see both at the following links: Vent Free Fireplace Inserts [1] Direct Vent Fireplace Inserts [2] Cost is similar, but vent-frees are a bit more economic, e...
Our Answer: This hopper measures 16 inches deep, 25 1/2 inches long, and 13 inches tall. From Page: SBI-AC01314 [1] Manufacturer's Product Number: AC01314 Our SKU: AC01314 Page ID: sbi-ac01314 Links: ------ [1] http://www.efireplacestore.com...
Our Answer: Unfortunately, it cannot. None of our electric fireplaces are currently available in a two-sided or see-through setup. From Page: NPL-EF39HD [1] Manufacturer's Product Number: EF39HD Our SKU: EF39HD Page ID: npl-ef39hd Links: --...
Our Answer: Unfortunately, no. There is no option for a remote control on the GVFT8. The only way to operate this unit is with the on/off switch on the GVFT8 itself. From Page: NPL-GVFT8 [1] Manufacturer's Product Number: GVFT8N Our SKU: GVFT8...
Our Answer: Unfortunately, not. Our surrounds and facings are designed to work specifically with the fireplaces for which they are manufactured. From Page: CUI-DVF2 [1] Manufacturer's Product Number: DVF-2-BL Our SKU: DVF-2-BL Page ID: cui-dv...
Our Answer: While this item is not what you need, you may be interested in purchasing a fireback to put in your fireplace. These will radiate heat back out of the fireplace. Please see this link for our selection of firebacks: Fireplace Firebacks [1]...
Our Answer: Unfortunately, the brick liner in this unit is not available in any other color. I assume you will have a chase cover made for this pipe, which has an outside diameter of 12 3/8". If you are passing through any floors or ceilings, you wil...
Our Answer: This mantel is indeed in stock and can ship directly. Standard ground transit will get this item to you in Arlington in about 3 days. From Page: CUI-MS48PG [1] Manufacturer's Product Number: MS-48-PG Our SKU: MS-48-PG Page ID: cu...
Our Answer: This grate is actually square. It measures 5 1/4" wide in the front and back. It is also 5 1/4" deep. From Page: UF-C-1812 [1] Manufacturer's Product Number: C-1812 Our SKU: C-1812 Page ID: uf-c-1812 Links: ------ [1] http://www...
Our Answer: Yes, you may use these elbows directly off your insert and connect the HomeSaver 6" liner from there. From Page: CPF-21657 [1] Manufacturer's Product Number: 21657 Our SKU: 21657 Page ID: cpf-21657 Links: ------ [1] http://www.e...
Our Answer: Indeed you may build up a 12-inch hearth and install this Plantation model. However, please note that you would need to also purchase the 48 Inch Floor Protective Hearth Spacer for it, found here: FMI 48 Inch Floor Protective Hearth Space...
Our Answer: Our vented Peterson log sets can indeed be converted from one gas type to another. We do not deal in the Pyromaster product line. I am unsure of the convertibility of this product. From Page: PTS-NOG45-2-24-SPK-26N [1] Manufacturer's...
Our Answer: This screen has an overall width of 52 inches, with the center section measuring approximately 31 inches across. Most of our 3 panel screens measure 48 to 56 inches in total width. You may consider using a smaller single panel screen inst...
Our Answer: This unit measures 36" tall. It is designed to be used with 5 x 8 direct vent components. However, being made by FMI, it would work best with other FMI components. In Response to Question: I have an existing Heat & Glo Model 6000TR w...
Our Answer: Please view the the installation instructions for this hood by downloading the PDF on the product page: Elite Square End Fireplace Hood with Lintel Mount - 36 Inch x 4 Inch [1] This hood will mount into the lintel of your fireplace, as il...
Our Answer: This particular model of stove is not multi-fuel certified and cannot burn corn. However, we do offer a couple of other multi-fuel models that can burn corn, along with several other fuels. They can be seen at the following links: US Stov...
Our Answer: The sound you are hearing is commonly called "oil canning". If the unit is fairly new, this can occur for the first several times the unit is burned. It is important to burn the unit for at least one hour on maximum temperature settings w...
Our Answer: Unfortunately, this flashing will not work for your particular needs. This is intended for an FMI pipe that has a 12" inner diameter, but a 15.5" outer diameter. We do carry a flashing for the Monessen SK8 chimney series, which has an 8" ...
Our Answer: This item should work well for your application. Or if you'd prefer to mix your own mortar, please check out our Dry Refractory Mortar by following the below link. Rutland Dry Refractory Mortar Mix - 10 Pound Tub [1] In Response to Ques...
Our Answer: While the venting system cannot end into your existing chimney, you can run the vent pipe through the existing chimney flue to the outdoors. The "chimney flue" that is mentioned in the manual is referring to the vent pipe from the unit it...
Our Answer: This starter pipe is approximately 15" in overall length. Currently, we do not have any other starter collars with different lengths than this item. From Page: CPF-69442 [1] Manufacturer's Product Number: 46DVA-ADP Our SKU: 46DVA-A...
Our Answer: This set allows for easy removal of the tools and has a stable base. While you may not be able to fit your hand through the loops, you can certainly gain the stability you need by grasping the loop. From Page: FSD-18003 [1] Manufactur...
Our Answer: Yes, you may install ventless gas logs in this fireplace. However, please note, as specified on in the owner's manual, you must purchase a hood for this unit if you install ventless gas logs. Please see page 18 of the owner's manual on th...
Our Answer: These types of mesh panel screens are indeed the kind used on most manufactured units. However, the Temco brand is no longer around and I do not have specific information that covers the opening dimensions of this unit. While the overall ...
Our Answer: While we do not carry any rugs that already offer the non-skid backing, we do offer two different sizes of backings that can be trimmed to fit your application. They can be seen at the following links: Goods of the Woods Non Skid Pad for ...
Our Answer: Per the manufacturer, you can indeed place this unit directly on carpet. From Page: FSD-7100A-O [1] Manufacturer's Product Number: 7100A-O Our SKU: 7100A-O Page ID: fsd-7100a-o Links: ------ [1] http://www.efireplacestore.com/fs...
Our Answer: The inside diameter, or dimension "A", is 9 1/8". This component is designed to trim the outside of a round ceiling support and is larger than the vent pipe itself. There is not a specific trim collar for the double wall pipe, as it canno...
Our Answer: This paint features more of a satin finish. It can be viewed by clicking the image of the paint swatch on this item page. Clicking the image will enlarge it; offering a better view. This paint should adhere just fine to hearth tiles but m...
Our Answer: It will be necessary to use a castable refractory cement to secure the frame of the damper into position. We carry this material at the link below: Rutland Castable Refractory Fireplace Cement - 12.5 Pound Tub [1] We will be happy to answ...
Our Answer: We do indeed still carry the 14" version of this same cap. It can be seen here: Draft King 14 in. Black Painted Galvanized Steel Round Bolt-On Single Flue Chimney Cover [1] You may place an order online, which will be processed automatica...
Our Answer: Due to the dimensions of your existing opening, it would be necessary to install a slightly narrower fireplace and trim the opening or modify the opening to be a bit taller. The current units we have will not fit exactly. Also, please let...
Our Answer: Your thoughts to fully frame in the firebox and venting run are right on track. However, this unit is not designed to be installed outdoors. Even if the unit is protected from the elements, the ambient humidity would wreak havoc on the un...
Our Answer: The dimensions listed on our site of 49" W x 31" H is actually for the screen itself and excludes the extra width of the tool hangers on either side of the screen. From Page: NPL-SC5 [1] Manufacturer's Product Number: SC5 Our SKU: S...
Our Answer: Indeed, you may. However, it should be placed at least 18" above the top of this fireplace. From Page: CUI-VFP36FP30LN-KIT [1] Manufacturer's Product Number: VFP-36-BP30LN Our SKU: VFP-36-BP30LN Page ID: cui-vfp36fp30ln Links: -...
Our Answer: For this fireplace, you will need to purchase the optional remote control separately. We recommend either the Ambient RCB On/Off Remote Control [1] or the Ambient RCST Standard Thermostat On/Off Remote Control [2]. The only additional req...
Our Answer: This mat is very flexible and will indeed be able to fit inside an 8" tube. Provided the tube is 54" long, of course. From Page: FSD-12202 [1] Manufacturer's Product Number: 12202 Our SKU: 12202 Page ID: fsd-12202 Links: ------ [...
Our Answer: Quite simply, the difference between DuraTech and DuraPlus is that DuraTech is a double-wall pipe and DuraPlus is a triple-wall pipe. In Response to Question: I am going to replace an old dura vent chimney that is corroding. It is 30 ...
Our Answer: The BD36B doors are actually finished in brass, rather than black. The BD36 doors will have a black finish. Both doors are the exact same design and will fit the same models of fireplace, the only difference is the brass finish on the BD3...
Our Answer: This ceiling support box is made to receive 8" DuraBlack (single-wall) stovepipe or 8" DVL (double-wall) stovepipe. We offer both on our website. These would connect to the ceiling support box with a close clearance adaptor (Dura-Vent 8-I...
Our Answer: You may want to call Empire, the manufacturer, to troubleshoot this issue. From Page: CUI-DVB1 [1] Manufacturer's Product Number: DVB-1 Our SKU: DVB-1 Page ID: cui-dvb1 Links: ------ [1] http://www.efireplacestore.com/cui-dvb1.h...
Our Answer: While it would be OK to use this as a panel in your gas fireplace, it is not recommended. You would be better finding a ceramic fiber panel to use, which would weight significantly less and would be less cumbersome to hold in place. With ...
Our Answer: The panels would need to be cut to size, using the existing panels as a template. You can cut these with a masonry or tile saw. Most panels are held in place with removable steel brackets. The existing brackets would need to be utilized w...
Our Answer: In a word, yes. This grate works perfectly well in a fireplace and being stainless steel it is ideal for outdoor applications. From Page: UF-C-7727 [1] Manufacturer's Product Number: C-7727 Our SKU: C-7727 Page ID: fsd-c-7727 Lin...
Our Answer: The Majestic Stove that you are interested in is made as a Direct Vent stove that requires 4x7 venting. So, as long as your existing masonry chimney has the available width to fit a 7" rigid direct vent pipe, you'd be good to use the unit...
Our Answer: If you are installing the fireplace as you mention, you will indeed need to select the Black Border assembly with tempered glass. This is listed as one of the options on the drop down menu on the item page when you order the fireplace. If...
Our Answer: Yes, we do sell inserts approved for use for mobile homes, but you must add a separately-purchased fresh air kit. Please see this example: Osburn 1100 Insert [1] Fresh Air Kit [2] Fresh Air Kit - Liner [3] From Page: SBI-DB03120 [4] M...
Our Answer: You could use this Heat-Fab stovepipe, but we would recommend using Simpson Dura-Vent products. You could use either the single-wall DuraBlack or the double-wall DVL stovepipe until you get to your wall, then convert to either double-wall...
Our Answer: These gaskets only require the running of a bead of gasket cement to seal them into place. Rutland E-Z Spread Fiberglass Stove Gasket Cement - 10.3 Ounce Cartridge [1] From Page: RUT-91N [2] Manufacturer's Product Number: 91N Our SK...
Our Answer: This paint will achieve that purpose, as will the Stove Bright paint you can see here: Stove Bright Flat Black Paint [1] From Page: CPF-43400 [2] Manufacturer's Product Number: 1A262H227 Our SKU: 1A262H227 Page ID: cpf-43400 Link...
Our Answer: This screen and the recommended screen rod will indeed fit into your specified opening. It would also be possible to use a slightly longer screen as well. We carry a 27 1/2 inch version that can be viewed here [1]. From Page: FSD-RMP242...
Our Answer: Please follow this link to download your manual. FMI Fireplace Manual [1] Please let us know if you have any additional questions. From Page: FSD-B42 [2] Manufacturer's Product Number: B42 Our SKU: B42 Page ID: fsd-b42 Links: ---...
Our Answer: We have adjustable fireplace hoods that range from 28"-48" in width, available in both 4" and 6" projections. These are also available in surface mount or lintel mount. Please see these pages and the accompanying owner's manual links whic...
Our Answer: We do offer this stove, which has cast aluminum cook surfaces: Napoleon 1150P EPA Wood Gourmet Cook Stove [1] Obviously, there are no stainless steel coils, but the cast aluminum is a better conductor. From Page: FSD-OB02000 [2] Manuf...
Our Answer: Most gas valves have a jam nut that holds the valve stem tightly in position. The nut can back off over time, which allows the stem to become loose, causing a gas leak. I recommend checking the nut before replacing the valve. A deep well ...
Our Answer: These are small rocks of varying sizes. From Page: PTS-STN-RIVERROCK [1] Manufacturer's Product Number: STN-RIVERROCK Our SKU: STN-RIVERROCK Page ID: pts-stn-riverrock Links: ------ [1] http://www.efireplacestore.com/pts-stn-rive...
Our Answer: The closest thing we have would be the SuperPro Adaptor plate. Please view it here: SuperPro All-Fuel Fireplace Adaptor Plate with Stainless Steel Collar - For Chimney Pipes with a 6-Inch Inner Diameter [1] From Page: CPF-77747 [2] Ma...
Our Answer: As far as how much area this fireplace will heat, a rough estimate would be about 1,000 square feet. The actual area heated would depend on your ceiling height, the windows and/or doors in the room, the insulation, et al. From Page: NPL...
Our Answer: While this flex pipe is ideal for making an offset, it cannot be passed through a wall. The pipe is not insulated like the rigid pipe is and will allow to much heat to radiate in the combustible framing members. You will only be able to u...
Our Answer: This item is intended to replenish vented gas log sets. From Page: RUT-587 [1] Manufacturer's Product Number: 587 Our SKU: 587 Page ID: rut-587 Links: ------ [1] http://www.efireplacestore.com/rut-587.html
Our Answer: This screen is intended to stand on the hearth in front of your fireplace. It does not require installation onto the fireplace front. From Page: FSD-18433 [1] Manufacturer's Product Number: 18433 Our SKU: 18433 Page ID: fsd-18433...
Our Answer: It is generally best to have the center section of these screens as close to your fireplace opening width as possible. From Page: UF-S-1184 [1] Manufacturer's Product Number: S-1184 Our SKU: S-1184 Page ID: fsd-s-1184 Links: ---...
Our Answer: This unit is a non-catalytic appliance that takes advantage of primary and secondary air for complete combustion. The secondary air is introduced via the secondary air tubes in the top of the fire chamber. From Page: NPL-2300 [1] Man...
Our Answer: Yes, it will. From Page: PTS-EPK-1P [1] Manufacturer's Product Number: EPK-1P Our SKU: EPK-1P Page ID: pts-epk-1p Links: ------ [1] http://www.efireplacestore.com/pts-epk-1p.html
Our Answer: This unit does indeed require the use of a 110V electrical outlet, in conjunction with the provided transformer for operation. The unit is provided with a battery backup that will allow the unit to operate in the event of a power outage, ...
Our Answer: Unfortunately, not. We do not currently offer a conversion kit for your unit. From Page: CUI-6000CKN [1] Manufacturer's Product Number: 6000CKN Our SKU: 6000CKN Page ID: cui-6000ckn Links: ------ [1] http://www.efireplacestore.c...
Our Answer: This stove is appropriate for spaces between 500-2,100 square feet. From Page: SBI-DB03030 [1] Manufacturer's Product Number: DB03030 Our SKU: DB03030 Page ID: sbi-db03030 Links: ------ [1] http://www.efireplacestore.com/sbi-db03...
Our Answer: Yes, this may be installed inside a brick firebox. Fireplace inserts in general must be installed in masonry fireplaces. Specifications for this model in particular can be found in the owner's manual, which you can be downloaded on this p...
Our Answer: This screen panel kit does include the attachment rings and coil pulls. The only thing that you will need to provide is the mounting rod. This kit has a pair of 24" panels, so there would be a lot of folds in the panels when used with a 3...
Our Answer: The tip of this bellow is made of cast iron. From Page: UF-C-6144 [1] Manufacturer's Product Number: C-6144 Our SKU: C-6144 Page ID: fsd-c-6144 Links: ------ [1] http://www.efireplacestore.com/fsd-c-6144.html
Our Answer: While unvented heaters may produce some odor it is not normal for the odor to be over powering or overly noticeable. However, a "burn in" is necessary to burn off the oils and lubricants used during assembly. It is recommended to open a f...
Our Answer: This Majestic chimney system has an 11" I.D. and a 14" O.D. It will readily connect to any section of existing Majestic 11CF chimney, using the built in twist lock mechanism. From Page: MAJ-11CF4 [1] Manufacturer's Product Number: 11C...
Our Answer: They told you correctly. Most all gas log manufacturer's require that you use their logs on their burner assemblies. This is true for our Peterson log sets, as well. In Response to Question: I have a Lennox see through fireplace and w...
Our Answer: Here are the shipping weights for our FMI Wood Fireplace 12-in. Diameter Chimney Venting Pipe for FMI Woodburning Fireplaces: 12-12DM 12'' length - 5 lbs 18-12DM 18'' length - 8 lbs 24-12DM 24'' length - 10 lbs 36-12DM 36'' length - 14 lb...
Our Answer: Unfortunately, FMI (the manufacturer of this unit) lists no approximate burn times or efficiency rating for this unit. This is a low-efficiency unit, and the burn time would depend on the quality of your firewood. From Page: FSD-C36LH ...
Our Answer: This heater has physical dimensions of 21.5" tall, 13.5" wide, and 7" deep. From Page: CUI-VSHR10T [1] Manufacturer's Product Number: VSHRN10T Our SKU: VSHRN10T Page ID: cui-vshr10t Links: ------ [1] http://www.efireplacestore.co...
Our Answer: This rod could clean a liner from the bottom up, however it will be difficult to do this from inside the insert. Most inserts will not allow direct access to the flue collar and you must slide the insert out of it's opening to gain access...
Our Answer: Here are the doors we have for the Majestic BC36 fireplace: Majestic Standard Bi-Fold Black Glass Fireplace Doors with Black Track - For Majestic 36 Inch Royalton and Designer Wood Burning Fireplaces [1] From Page: MAJ-36GDKBKSR [2] M...
Our Answer: This particular blower assembly is intended for use only with Napoleon's GD19 Vittoria gas fireplace. Due to the thermostatic settings of the blower, it is unlikely that it would function properly in an electric fireplace. My recommendati...
Our Answer: When sizing fireplace doors, you need to measure your fireplace's opening, including front width at the bottom and top and height at the far left and far right. From Page: ADC-800400 [1] Manufacturer's Product Number: X800400 Our S...
Our Answer: Unfortunately, no. While Napoleon has recently introduced the same decorative fire art for the LHD50 that is available for the LHD62, they have not yet designed a log set to fit the LHD50. While it is possible that they will introduce thi...
Our Answer: You have a couple of options to connect 6" DuraTech pipe to 6" Dura-Black single-wall stovepipe. Please see the following items: Dura-Black Welded Steel Stovepipe Slip Connector - 6-Inch Diameter [1] This is a slip connector for use with ...
Our Answer: This item is indeed a ring only. It will come shipped in individual sections that can be bolted together, then used to surround a manufactured or dug out fire pit. From Page: PDM-BEARCUB [1] Manufacturer's Product Number: BEARCUB Ou...
Our Answer: Per the manufacturer, these andirons are approximately 16" in height and 7" in width at the base. They are designed to be a proportional fit to the 60" Monessen Covington model. From Page: CUI-FAI16 [1] Manufacturer's Product Number: ...
Our Answer: No, this stove does not have a rear vent option. The only such wood stove we offer that does is the Napoleon 1600C Series Cast Iron Wood Burning Stove [1]. The center of that 6" diameter flue collar would be 24.125" from the bottom of the...
Our Answer: This profile mantel is only available in 52 and 48 inch varieties. However, the mantel could be narrowed by cutting the breast board and top shelf. Material could be removed from the end of the breast board and the shelf could be shortene...
Our Answer: Yes. All of our Goods of the Woods rugs do indeed meet CPSC FF1-70 flammability test. From Page: FSD-10310 [1] Manufacturer's Product Number: 10310 Our SKU: 10310 Page ID: fsd-10310 Links: ------ [1] http://www.efireplacestore.c...
Our Answer: Indeed, this blower will come with a 110 volt power cord, variable speed switch and thermodisc, as well as the requisite wiring harness. From Page: NPL-EP62-1 [1] Manufacturer's Product Number: EP62-1 Our SKU: EP62-1 Page ID: npl...
Our Answer: Assuming you have this model fireplace (FMI Bungalow B42L), we can indeed get the replacement refractory panel for the back. It is part number 108310-01 (see page 18 of the owner's manual at this link: http://lib.store.yahoo.net/lib/yhst-...
Our Answer: The blower and thermostat are not included with this furnace. You may select them from the Accessories tab on this unit's item page. Without these items, the unit would heat your room/home via radiant heating and would be controlled manua...
Our Answer: This screen has a projection of approximately 6 inches, per the manufacturer. From Page: UF-S-6957 [1] Manufacturer's Product Number: S-6957 Our SKU: S-6957 Page ID: uf-s-6957 Links: ------ [1] http://www.efireplacestore.com/uf-s...
Our Answer: This is a vent kit for a direct vent fireplace, which should not be causing problems with cold draft, as the unit should be sealed off from the room with a glass panel affixed to the front. While some cold air can radiate through the glas...
Our Answer: Unfortunately, we are not familiar with this accessory manufactured by Dexen. However, comparing it to our Peterson PCC1, we can say that no real repair is available for these sound modules. They are a closed unit and no replacement parts...
Our Answer: The Vail series of vent-free fireplaces features a solid panel mesh screen that covers the opening. As with any vent-free fireplace, there is no glass door option, only decorative screen doors for select models. From Page: CUI-VFP32FP3...
Our Answer: You can download the PDF version of these instructions on this item page under product manual.. However, application is a breeze. A form is not required. You'll simply apply the CrownSeal with a trowel or putty knife, then scrape off the ...
Our Answer: These boots will support the fireback with a slight angle towards the back of the firebox. It would be necessary to move the fireback forward in the firebox to compensate for the shape of the back wall. From Page: PEN-SB3 [1] Manufact...
Our Answer: You will need a listed stainless steel 6" liner for this insert. Here are a couple of options: DuraFlex SS Stainless Steel Chimney Liner - 6 inch x 25-ft. [1] This has a 25-foot length, we also have it available in 15-, 20-, 30-, and 35-f...
Our Answer: If you are planning on installing a gas appliance into a bathroom or bedroom, it must be a vented appliance. Vent free units cannot be installed into this type of room. That being the case. I would recommend one of our direct vent units. ...
Our Answer: First of all, thank you for the kind review and publicity for our site. Of course, thank you also for your business. This venting kit would get the job done for you without the need to add-on any other components. I tried to build this ki...
Our Answer: Any of our vent free Peterson units, including our PTS-VOG8R-16-ManualP, would work just fine in this application. Like you mentioned, you'd want to make sure the stove remained open while the set is on. Also, we'd want to double-check yo...
Our Answer: The outer diameter of the biggest locking ring on this cap is 11 1/8". If you have a 13" diameter pipe, it is most likely that you have a different brand of flue pipe, as the next size up in the Majestic line has a 14" outer diameter ring...
Our Answer: You may elevate this firebox up to the point where you still have AT LEAST 42" from the top of the unit to your ceiling. Please see this link for the owner's manual: http://fmisupport.hcents.com/supportdocs/WS%20105163-01E.pdf Page 8-11 w...
Our Answer: The remnants of Martin Hearth have since been absorbed by Majestic Hearth. While they did retain some of the same model numbers, the boxes have been redesigned extensively and do not use the same liners. We have since exhausted our stock ...
Our Answer: Unfortunately, no, this model is not available in a corner unit. However, you may also be interested in the Classic Flame Martha's Vineyard Dual Corner/Wall Electric Fireplace with Mahogany Mantel [1]. From Page: SEI-FE9278 [2] Manuf...
Our Answer: The RCK-K can indeed serve as a replacement for the RX05 model that you have currently have. This will allow you to keep the same functions and thermostatic control that you have now. From Page: HPC-RCK-K [1] Manufacturer's Product Nu...
Our Answer: Yes, sir our FSD-OBCO19N1F is a vented appliance. The minimum vent diameter depends on the height of the chimney. For example, a 10' chimney requires a minimum opening diameter of 5". From Page: FSD-OBCO19N1F [1] Manufacturer's Produc...
Our Answer: Unfortunately, we do not have dimensions for the item you inquired about. The reason is that FMI, the manufacturer of these panels, makes these panels specifically for their 36"Cape Cod firebox only, as they are not intended for use with ...
Our Answer: This blower mounts on the back of the stove without utilizing any knockout. The blower will require approximately 5 inches of space when mounted. Unfortunately, there is no way to decrease the space requirement, so it will be necessary to...
Our Answer: he heat shield and the blower are separate items. These are accessories for the Napoleon 1600C Series Cast Iron Wood Burning Stove. Here's a link to the heat shield: Napoleon 1600C Wood Stove Rear Shield [1] Here are links to the blowers:...
Our Answer: Per the manufacturer, the ports in the burner pipe are a little under 1/8 of an inch in diameter. From Page: FSD-611-LP-B [1] Manufacturer's Product Number: 611-LP-B Our SKU: 611-LP-B Page ID: fsd-611-lp-b Links: ------ [1] http:...
Our Answer: This particular set is a complete model that only requires you to provide an incoming gas line to your fireplace. All decorative embers, grate, burner, etc are provided for the install. It is necessary to install this set into an existing...
Our Answer: These bellows feature handles made of pine with an oak finish. The trim is indeed real leather. From Page: CPF-68060 [1] Manufacturer's Product Number: 1110 Our SKU: 1110 Page ID: cpf-68060 Links: ------ [1] http://www.efireplac...
Our Answer: These trim kits are designed to be installed onto one of four Napoleon fireplaces - the BGD33NR, BGD34NT, GD33NR, and GD34NT gas fireplaces. They come in preset sizes and cover openings 35" W and 30" H. What type of fireplace do you have?...
Our Answer: What you need would depend on the type of pipe you already have. If you have a direct vent furnace that utilizes 5 x 8 venting, and you already are using the DirectVent Pro pipe, then yes, this will work. Otherwise, you would need to iden...
Our Answer: The main advantage of the lintel mount hood is that it does not take up any space on the facing of your fireplace. It is also helpful because you do not have to drill into the facing material, which can be difficult to do if it is tile or...
Our Answer: apologize for the trouble you are having with your remote receiver. Since the unit appears to be receiving the signal generated by the remote, the first thing I would do is to double check that there is not a bad connection between the re...
Our Answer: We do have a 17" x 17" fireback. Please see the item here: Renommee Fireback [1] We also have a plain, stainless steel 15" x 15" fireback you may be interested here: Copperfield Stainless Steel Radiant Fireback - 15-in. X 15-in. - 70020 [...
Our Answer: This griddle gasket uses graphite impregnated fiberglass only. It does not utilize any type of wire mesh in it's construction. From Page: FSD-VCGG [1] Manufacturer's Product Number: VCGG Our SKU: VCGG Page ID: fsd-vcgg Links: ---...
Our Answer: BTU output from this unit will vary largely, depending on the type of wood that is burned. Softwoods will create a small, cooler fire. Hardwoods can yield a much higher BTU output, usually in the 70 to 80K range. This unit, being an open ...
Our Answer: Thank you for shopping at eFireplaceStore.com. The dimensions for this faceplate-door kit are as follows: 40.25" peak height (top of the keystone), 36.36" at the top of the shoulder before it arches, and 40.5" total width. Please note tha...
Our Answer: This hood is designed to be installed directly onto the lintel of your fireplace. If you have an enclosure on your fireplace, you may be interested in one of our surface mount units. We have several lengths available. Please follow the be...
Our Answer: This unit can be converted to B-Vent with the Napoleon GS-150KT. Please follow the below link to view this item. Napoleon B-Vent Gas Stove Pipe Adaptor Kit [1] From Page: NPL-GDS60 [2] Manufacturer's Product Number: GDS60-1N Our SKU...
Our Answer: Unfortunately, we do not carry any see-through or two-sided electric fireplaces. In addition to the fireplace you inquired about, here is our selection of electric fireplaces: Electric Fireplaces [1] In Response to Question: Is this i...
Our Answer: Assuming this heater would be installed in a room with 8 foot ceilings and decent insulation, this model would be able to heat an area of approximately 800 square feet. Factors such as high ceilings, poor insulation, and a divided floor p...
Our Answer: I spoke with the technical department at Ambient Technologies and they reminded me that receivers with four-wire connectors are usually ones with a thermostatic control. In this case, since you are looking to replace your variable flame r...
Our Answer: While this screen's outside dimensions will completely cover your fireplace opening, the door size is a bit small. The use of your fireplace may be a bit limited. The below screen may be a little closer to a proper fit for your applicatio...
Our Answer: Yes, you may use cement that we sell to repair. For example, this furnace cement can be used for applications 1/16" up to 1/4" thick: One Pint Tub of Black Furnace Cement [1] This fireback does indeed radiate heat back into the room, and ...
Our Answer: This fan features both a thermostatic switch and a manual speed control. The fan will not activate until the switch has detected sufficient heat for the blower to be effective. Once the blower is operating, you can manually control the bl...
Our Answer: This item comes complete with burner, coals and basket. However, it is a vented appliance. Please follow the below links to view our vent free options. Vent Free Burners: Victorian Hearth Vent-Free Natural Gas Burner with Realistic Coals ...
Our Answer: This price is for all three sections in this liner kit. However, this kit is not meant for the SR42, which is a wood burning fireplace. These ceramic liners are meant for gas only and will deteriorate rapidly in a wood burning unit. I can...
Our Answer: Unfortunately, not. We currently only carry these complete kits and not their component parts. From Page: USS-BSK1000 [1] Manufacturer's Product Number: BSK1000 Our SKU: BSK1000 Page ID: uss-bsk1000 Links: ------ [1] http://www....
Our Answer: Depending on the type of stovepipe you currently use, it may be possible to keep your existing pipe with this stove. We sell some 6-to-8 inch diameter stovepipe-to-stovepipe increasers. Please see the following links: Imperial 6 Inch x 8 ...
Our Answer: The 1001BE is not a suitable replacement for SkyTech's 1001SR. However, the MRCK is. Please follow the below link to view this item. SkyTech SKY-MRCK Rotary Adjustable Flame Height Remote Control - For Operating Maxitrol Servo Motor Valve...
Our Answer: The OD of this pipe measures 6 5/8". From Page: CPF-686-6GVPIPE [1] Manufacturer's Product Number: 6GV06 Our SKU: 6GV06 Page ID: cpf-686-6gvpipe Links: ------ [1] http://www.efireplacestore.com/cpf-686-6gvpipe.html
Our Answer: The Arlington is a great free-standing stove option. It will actually generate a bit more BTU than the Tahoe fireplace that you originally had. From Page: NPL-GDS20 [1] Manufacturer's Product Number: GDS20N Our SKU: GDS20N Page I...
Our Answer: You can indeed continue to use the unit if the facade paint begins to peel, as it is a non flammable paint. If the paint begins to peel, the face of the unit can be redone with any of our high heat paint products. A good product to use wo...
Our Answer: While it's primary purpose is to add humidity to the air, this kettle can indeed be used to boil water for consumption. However, it is recommended to clean the inside of the kettle thoroughly, then boil water in the kettle 2 or 3 times to...
Our Answer: This is indeed the correct blower assembly for the model of fireplace that you list. Please let me know if you have any installation or ordering questions. From Page: CUI-FBB4 [1] Manufacturer's Product Number: FBB-4 Our SKU: FBB-4 ...
Our Answer: This item features dimensions of 40" wide x 37 1/2" tall x 24" deep. From Page: CUI-VPN36-A [1] Manufacturer's Product Number: VPN36-A Our SKU: VPN36-A Page ID: cui-vpn36-a Links: ------ [1] http://www.efireplacestore.com/cui-vp...
Our Answer: This type of gas fireplace insert is intended specifically for use with a masonry/clay chimney flue. However, the flue must be lined using one of the direct vent liner kits available from Empire. This kit consists of a pair of 3" aluminum...
Our Answer: No, the ceramic brick liner and the medium black trim kit are extra pieces not included with the fireplace. Both of these items can be found in the "Accessories" tab on the fireplace's item page. From Page: CUI-CDVT36NSC7 [1] Manufac...
Our Answer: Unfortunately, the trim for this unit is not available in any color other than black. The kit is the Majestic BLMTK32C Medium Black Fireplace and Firebox Trim Kit [1]. Please note that while the other colors are still displayed in the pho...
Our Answer: Many thermostatic controls are not pole specific. They work fine with the connections made in either location. This is likely the reason that each of your wires are bare with no identifying features. The unit should operate with the wires...
Our Answer: Our Majestic pipe is designed specifically to connect to other Majestic pipe or a Majestic appliance. However, we do offer SuperVent pipe manufactured by Selkirk. Please follow the below link to check it out. SuperVent All-Fuel Insulated ...
Our Answer: Per our supplier, this agent should actually work rather well for you. As it turns out, the crown forms with which this product is made to work are made of a type of Styrofoam. In Response to Question: My name is Andrew Newell and I ...
Our Answer: To get a better working knowledge of this burner, I recommend that you download the installation manual from this webpage. The burner does indeed lie flat on the floor of your fireplace. From Page: PTS-G45-2-GLA-24S-APK-15P [1] Manuf...
Our Answer: The mantel this unit is shown installed into can be seen at the following link: Vantage Hearth 21 Inch Traditional White Wooden Wall Mantel [1] This unit is indeed remote ready and can be utilized with the remote at the following link: Va...
Our Answer: This mantel is designed with the Vantage Hearth, Classic Hearth series in mind. These units measure 26 3/4" wide by 26" tall. As a result, the opening in this mantel is similarly sized and comes with decorative wooden panels to trim the u...
Our Answer: The 812 AirMax is an excellent choice for use with a propane stove, as it will begin to circulate air at a relatively low temperature, unlike other models. Your room size will not be an issue for circulation, but the high ceilings will ha...
Our Answer: All three sides of this peninsula vent-free firebox will have mesh pull screens; there is no glass on the unit. Please see page 16 of the owner's manual [1] for an illustrated parts breakdown. From Page: CUI-FBPS [2] Manufacturer's P...
Our Answer: We should be able to special order these brick liners for you. Would you mind replying with the actual model number and serial number from your fireplace so that we can be sure to order the correct pieces? In Response to Question: I n...
Our Answer: The brass components in the photo are upper and lower louvers, as well as the surrounding trim. I will be happy to check into the correct replacements for this unit. Please provide the manufacturer name and model number of the fireplace a...
Our Answer: It sounds like you are referring to the framing kit that is required to finish these Napoleon fireplaces. You would need either FK80-A (arched) or FK80-R (rectangular). We do not separately list this item from the GD80 on our site but we'...
Our Answer: This unit does not come with a blower. However, one can be added. Please look in the accessories tab or follow the below link to view this accessory. Napoleon EP62-1 Variable Speed Blower [1] From Page: NPL-1400 [2] Manufacturer's Pro...
Our Answer: Napoleon does not include a flex connector on the GDI-30N because some local jurisdictions require a rigid gas line connection to gas appliances such as that insert. This item will indeed connect to the GDI-30N, as one end of this connect...
Our Answer: Indeed we do, please see this link for these Decorative Arch Louvers for the Empire 32" Vail and Breckenridge units: Empire Decorative Arch Louvers - For 32 Inch Fireboxes and Fireplaces [1] From Page: CUI-FBG36A [2] Manufacturer's Pr...
Our Answer: The manufacturer offers a 90-day warranty on this fireback, and a replacement will be shipped to you at no charge if it happens to crack in that time frame. This is a very rare occurrence, but you do have coverage against it for 90 days. ...
Our Answer: The Monessen DBX units are only available in a 24" size. Between the DFS and DFX, the DFS is the larger, warmer fireplace. The DFS is capable of up to 34,000 BTU and is suitable for spaces as large as 2200 square feet. The DFX can produce...
Our Answer: Yes, this item will meet your needs. From Page: CPF-19050 [1] Manufacturer's Product Number: 19050 Our SKU: 19050 Page ID: cpf-19050 Links: ------ [1] http://www.efireplacestore.com/cpf-19050.html
Our Answer: This picture is true to the actual product. After being pulled in by the blower assembly on the left, heated air is forced out through the slats on the right front. bottom of the grate. From Page: FSD-GWH2220 [1] Manufacturer's Produ...
Our Answer: Gas log sets are designed to burn very efficiently without producing soot. As such, they should not contribute to the staining on the front of your fireplace. However, this set would not be ideal for an outdoor application. An outdoor fir...
Our Answer: This would be an excellent replacement screen for your application. The pair of 24-inch panels will completely screen the opening with some decorative draping. From Page: FSD-2418 [1] Manufacturer's Product Number: RMP2418S Our SKU:...
Our Answer: No, this Innsbrook insert model has a built-in modulating thermostat with no option to add a remote control. For the same insert with remote ready controls, please see the Medium Innsbrook Vent-Free Gas Fireplace Insert with Millivolt Con...
Our Answer: When dealing with a vent-free set in a masonry fireplace, your options will be limited. There is no blower that can be used with a vent-free log set when used in a masonry fireplace. Unless the fireplace has a built-in housing to accept a...
Our Answer: While Napoleon does offer fresh air kits for most of their stoves, the 1100C does not currently offer one. This is due to the smaller size of the combustion chamber that eliminates the need for combustion air in most circumstances. In cas...
Our Answer: Unfortunately, we do not currently offer screens in the dimensions you request. The extra width could removed or simply gathered at the side of the fireplace opening. From Page: FSD-2422C [1] Manufacturer's Product Number: RMP2422S ...
Our Answer: This electric insert is meant for installation into a mantel cabinet. However, to be sure this would work with your frame, you would need to check your dimensions against those listed on the page, and we would need to determine the proper...
Our Answer: We do sell the FMI 12" Inner Diameter pipe that is required to vent this fireplace. Please see a 48" length of this pipe at the following link: FMI Wood Fireplace 12-in. Diameter Chimney Venting Pipe for FMI Woodburning Fireplaces - 48-in...
Our Answer: To be certain this adapter will fit, it will be necessary to measure the oval opening on your stove. There are many different sizes of oval that have been used between different brands and a standard size was never really established. You...
Our Answer: All of our surface mount hoods are indeed adjustable, unfortunately. More than likely, they would interfere with the operation of your glass doors. However, you may be interested in our Surface Mount Hoods for Glass Enclosures. The hoods ...
Our Answer: This particular mantel has not been tested for use in an outdoor environment. Although it is constructed of high quality material and it will be covered, I fear the humidity will take a toll on the unit over time. I cannot advise that it ...
Our Answer: The 6" description refers to the diameter of the slip connector. The overall length is 11" and it can be used to add up to 9.5" of additional length to your stovepipe installation. A minimum of 1.5" of the connector must overlap the pipe ...
Our Answer: This insert has a BTU rating of 20,000 BTU/Hr. Indeed, code calls for no more than 10,000 BTUs in a bedroom, and the manufacturer makes it clear that you may not use this in a bedroom or bathroom. Unfortunately, there is no way to change ...
Our Answer: Chimney size is very important. We strongly recommend that you vent with the same diameter as the flue outlet on whatever stove you end up choosing. Different stoves call for different diameters based on engineering and what the manufactu...
Our Answer: Because of the fact that this product was not formulated to Jotul's paint codes, it will definitely have some variance. I cannot say exactly as to how well it would match, due to many factors that change the paint color on stoves over tim...
Our Answer: You are correct. When purchasing our CUI-GCUF32C-F, the gas log set is not included. You have the option to pick any of our vent free log sets for installation into this firebox. Due to the dimensions of this firebox, we would recommend y...
Our Answer: This Cathedral Support Box will include a trim collar that fits around the outside of the box to secure it to your slanted ceiling. The trim collar is free-floating so it can be angled to any degree necessary. From Page: CPF-67682 [1] ...
Our Answer: Most log lighters do not offer a high enough flame to offer a good appearance with gas logs. For maximum affect and to guarantee proper positioning of the flame with the logs, it is highly recommended that you purchase a burner and log ki...
Our Answer: The cap in the photo will not be included. The cap would be specific to the type of chimney system that you would be installing through the surround. It would be necessary to run the pipe to the top of the surround, then install the prope...
Our Answer: While in some cases you can get a reducer piece to do as you describe, it is never recommended to decrease the flue size to smaller than your appliance's opening. Please see your owner's manual for details. From Page: CPF-69122 [1] M...
Our Answer: Using this gas valve in place of one of our valves should not be a problem. We usually do not recommend this, but this particular model is almost a perfect replica of the APK-15 valve that we currently sell. You would simply need to order...
Our Answer: Depending on ambient temperature and conditions, it can take up to 7 days for this product to fully cure. Longer cure times usually occur in high humidity or were the product is used generously. From Page: FSD-71 [1] Manufacturer's Pr...
Our Answer: Our CrownSeal Flexible Coating has an approximate coverage of 18 sq. ft. per gallon at a 1/8" thickness. Due to this coverage and the size of your crown, I would recommend a smaller container of this sealant. Take a look at our CPF-24565:...
Our Answer: These Victorian Hearth inserts are designed to be used with the below firebox. Please follow the below link to view this item. Victorian Hearth 301 Zero Clearance B Vent Firebox [1] This unit will not be large enough to house an 18" log s...
Our Answer: The inside space between the rear legs of this grate will be approximately 19 1/8". The grate sizing will very slightly during manufacturing, so please allow up to 1/2" of variance. From Page: FSD-18600 [1] Manufacturer's Product Numb...
Our Answer: Your flue should be kept open while using this product. From Page: FSD-210 [1] Manufacturer's Product Number: 210 Our SKU: 210 Page ID: fsd-210 Links: ------ [1] http://www.efireplacestore.com/fsd-210.html
Our Answer: This model of poker is not available in a model that can be hung. Because of the fact that it is sold individually, it is assumed that it will indeed be placed in a corner, rather than being used as part of a complete tool set. Most sets ...
Our Answer: It can indeed be relocated from room to room. However, due to it's BTU rating it cannot be installed in a bedroom. From Page: CUI-VFD26FM30NN [1] Manufacturer's Product Number: VFD-26-FM30-NN Our SKU: VFD-26-FM30-NN Page ID: cui-...
Our Answer: This unit only requires a framing depth of 21". This dimension assumes the use of 1/2" wall board as finishing material. From Page: CUI-VFP36SB2EF [1] Manufacturer's Product Number: VFP-36SB2E-F Our SKU: VFP-36SB2E-F Page ID: cui...
Our Answer: Our Shenandoah Mantel Shelf is a solid wood shelf. However, the corbels are packaged separately and will need to attached upon installation. This unit weighs approximately 33 pounds. From Page: PRM-412 [1] Manufacturer's Product Numb...
Our Answer: This insert is meant only for installation into a pre-existing masonry fireplace or manufactured fireplace specifically listed to accept inserts (The factory built fireplace must be listed per UL 127 or ULC S610.). From the owner's manual...
Our Answer: These two part numbers you provided are for the same blower. The GZ550-1KT blower will work with your fireplace. This has been verified this with Napoleon's technical department. From Page: NPL-GZ550-1KT [1] Manufacturer's Product Nu...
Our Answer: Converting a Peterson Real Fyre log set from Propane to Natural gas only requires the swapping out of the Air Mixer on the burner for a Fuel Injector. As well as the replacement of the Vermiculite ember fill with Peterson Select Sand (PTS...
Our Answer: Indeed it is. Olefin fiber is natural resistant to flame and cinders. It is designed to protect your floor, while maintaining a decent appearance over time and use. From Page: FSD-10730 [1] Manufacturer's Product Number: 10730 Our S...
Our Answer: Although it is always better to remove the damper throat to gain better access for vent pipe installation, aluminum liners can usually be compressed up to one inch to fit through the damper throat. Because of the fact that you are already...
Our Answer: Our ash buckets do indeed feature a double bottom for extra safety. From Page: UF-C-1709 [1] Manufacturer's Product Number: C-1709B Our SKU: C-1709B Page ID: uf-c-1709 Links: ------ [1] http://www.efireplacestore.com/uf-c-1709.h...
Our Answer: This cement will be dry to the touch within a few hours. After that, you may use your stove normally. The first fire you burn can be of normal size and it will indeed serve to fully cure the cement. From Page: CPF-81300 [1] Manufactu...
Our Answer: Yes, this paint is suitable for your needs, as is this paint: Copperfield Black Gas Appliance Firebox Paint [1] From Page: CPF-43205 [2] Manufacturer's Product Number: 6304 Our SKU: 6304 Page ID: cpf-43205 Links: ------ [1] http:...
Our Answer: The mantel shown is our Medium Distressed Oak finish. This mantel is shipped with a wall cleat for attaching to your fireplace. From Page: PRM-412 [1] Manufacturer's Product Number: 412-24 Our SKU: 412-24 Page ID: prm-412 Links:...
Our Answer: These tongs are operated by grasping and lifting the small horizontal bar located directly beneath the spiraled handle. From Page: CPF-71893 [1] Manufacturer's Product Number: WR-02T Our SKU: WR-02T Page ID: cpf-71893 Links: ---...
Our Answer: While you cannot adjust the flame height on this unit yourself, all flames will be random by design, flame height will go up and down accordingly. Yes, there is an electric blower fan available for this unit, please see it here: Empire FB...
Our Answer: While your unit and the one listed are both Vent Free fireboxes, I believe the similarities end there. I am not familiar with any of our units that have a blower assembly similar to the one in your firebox. You may try searching for a dat...
Our Answer: Please advise if you are looking for an insert to slide into an existing masonry fireplace/chimney, or if you just need to find a unit that will fit those dimensions in a wall or a mantel cabinet. With this information, we can provide sug...
Our Answer: You are correct regarding this fireplace's zero clearance to combustible against its back wall. The same is true for the sides of the firebox, as well. There is an available blower and brick liner for this unit, as well. These items can b...
Our Answer: In theory, this should be the correct damper for your needs. The minimum interior dimensions for proper fit of this damper is 10" x 10". As long as your flue does not measure any smaller than this, the Lyemance damper will suit your needs...
Our Answer: A blower can help to an extent, but the fireplace must be a model of firebox that can accept a blower system. Is the wood burning unit a masonry fireplace or a prefabricated metal unit? You may also consider installing a deflector hood, i...
Our Answer: Usually, you will need to contact the retailer that the unit was purchased from. They will file a warranty claim for replacement parts with Southern Enterprises. On some occasions, you may be instructed to contact the manufacturer directl...
Our Answer: While this tee does not come with a cap as standard, we do offer the following item that is compatible for use with the tee: HomeSaver RoundFlex Tee Cover for 6 inch Chimney Liner [1] From Page: CPF-21045 [2] Manufacturer's Product Nu...
Our Answer: This rock media kit can indeed be used to replace the glass media that is provided with the unit. The rocks must be used in conjunction with the RAK-36 adapter kit, seen here: Napoleon RAK36 River Rock Adaptor Kit [1] You must use the ada...
Our Answer: This stove does indeed offer an optional heat shield for close clearance applications. It can be viewed in the accessories tab listed above, along with other options for the stove. From Page: SBI-DB07200 [1] Manufacturer's Product Nu...
Our Answer: Certainly. An insert is one of the most straight forward wood burning appliances to install. As long as your masonry or manufactured chimney is in good condition and you have good general knowledge of appliance installation, the job shoul...
Our Answer: We do not organize our blower selection by overall dimension. Rather, we list them by compatible fireplace model. For example, this blower is designed for use with Empire's Breckenridge fireplace. If you'd like to reply with your fireplac...
Our Answer: Unfortunately, we do not currently offer a 26" direct vent unit. However, we do offer a 27" unit. Please find it below. Small Loft Direct Vent Gas Fireplace with Remote-Ready Millivolt Controls [1] From Page: CUI-VFD26FP30L10N [2] Man...
Our Answer: There is no standard liner with this firebox; there is none included. You must choose one of the options for liner listed in the "Accessories" tab (to the immediate right of the "Item Description") on this page. From Page: CUI-VFD32FB0L...
Our Answer: These can only be used in one room. You'd simply have to pick in which room you'd prefer to place it. From Page: PTS-PCC1 [1] Manufacturer's Product Number: PCC1 Our SKU: PCC1 Page ID: pts-pcc1 Links: ------ [1] http://www.efire...
Our Answer: This item is designed for use with direct vent co-linear vent system that employ a pair of 3" liners. We should have a cap that will work for you, though. From Page: CUI-HEDVRT [1] Manufacturer's Product Number: HEDVRT Our SKU: HED...
Our Answer: The temperature of the stove pipe will exceed the rating for this particular product. Instead, I would use Rutland Pre-Mixed Black Furnace Cement - 10.3 Ounce Cartridge [1]. This high temperature, semi-flexible sealant will allow you to a...
Our Answer: This damper plate is designed to be used in masonry fireplaces as a replacement. It is not for use with manufactured fireplaces like yours. From Page: CPF-26250 [1] Manufacturer's Product Number: 97-010 Our SKU: 97-010 Page ID: cp...
Our Answer: Unfortunately, the MBU36 does not offer provisions for a blower, as it is a smooth faced model and does not have the built in housing that the MBUC36 has. From Page: NPL-64KT [1] Manufacturer's Product Number: GS-64KT Our SKU: GS-6...
Our Answer: Rough opening requirements for the DVCD32: 35 3/4" H 34 3/8" W 16 3/8" D Please download the manual from this item page. The FSD-ROOS-42 should work fine, as the interior dimensions are larger than what you need to frame this fireplace (4...
Our Answer: In addition to the different styling of the Olde World sets, the finish is darker than the vintage iron. It gives the appearance of iron that has not suffered the effects of corrosion and appears to be newly forged. The vintage iron sets ...
Our Answer: This damper's approximate physical dimensions are 7" D x 34 1/2" W. So, it should work just fine in your application. From Page: CPF-26265 [1] Manufacturer's Product Number: 97-014 Our SKU: 97-014 Page ID: cpf-26265 Links: -----...
Our Answer: This door would indeed cover the entire opening in your masonry floor, however the opening would need to be elongated slightly to make this item fit. It requires an 8 5/8" opening for the frame to seat, so 5/8" of surrounding mortar or br...
Our Answer: Yes, this conversion kit will work with your DESA unit. The model number is still the same as a Vantage Hearth, and its roots indeed lie with DESA. In Response to Question: I have a Desa Fireplace, the model#: VKC36P. I want to conve...
Our Answer: Unfortunately, we do not offer this mantle or any other in a 60" interior width. 56" is as close as we come. From Page: PRM-120 [1] Manufacturer's Product Number: 120-48 Our SKU: 120-48 Page ID: prm-120 Links: ------ [1] http://...
Our Answer: According to the manufacturer, the weather enclosure is a solid stainless panel that has a riveted stainless handle attached for installation. Please keep in mind that the panel cannot be installed on a unit that has glass doors already i...
Our Answer: This hood is manufactured with masonry fireplaces in mind and while it can be used with some manufactured fireplaces, it is not an ideal match to your unit. Even though DESA has gone out of business, the subsequent company, FMI, still mak...
Our Answer: Unfortunately, this product would not be able to withstand the heat on the inside of a wood burning fireplace. The paint would quickly discolor and eventually peel. The only product that we currently have that can withstand the interior t...
Our Answer: These are ceramic fiber panels meant for use only in a gas fireplace. However, we do offer some universal refractory panels that will work for your woodburning fireplace. Please see the following links: Hargrove Replacement Fireplace Refr...
Our Answer: This fireplace can generate up to 25,000 BTUs, which will heat approximately 700 square feet. However, B-Vent units are very inefficient and most of that heat will be lost up the flue. We recommend using a direct vent unit, if possible, i...
Our Answer: Because the unit has a heat register that is mounted in the top of the fireplace, a minimum distance of 36 inches must be maintained above the unit to prevent any damage to electronics. From Page: NPL-EFL48 [1] Manufacturer's Product ...
Our Answer: We would strongly recommend not to do this, as, since the face of the insert is not the shortest part, you would not be able to pull the insert out of your fireplace once it is installed. This is one of the reasons the manufacturers make ...
Our Answer: You can indeed connect a section of rigid pipe via an elbow to a length of flexible venting. However, the length of your horizontal run is dependent upon the height of the vertical section. Please visit the venting requirement graph found...
Our Answer: These doors are only for use on select manufactured FMI, Vantage Hearth or DESA woodburning fireplaces. If you have a manufactured fireplace, please reply with the manufacturer and model number, and we can research available doors. Please...
Our Answer: This item definitely leans toward a modern styling. There are no logs. Instead, it features just a burner. From Page: CUI-OLP42FP72S [1] Manufacturer's Product Number: OLP-42-FP72SN Our SKU: OLP-42-FP72SN Page ID: cui-olp42fp72s ...
Our Answer: Per the manufacturer, these 42GDKBK doors actually require six (6) #10 x 1" sheet metal screws for installation. These should be readily available at a local hardware store. In Response to Question: In order to install these doors, t...
Our Answer: Most all of our fireplace replacement liners are specifically designed for particular fireplaces. However, we do offer a couple of universal fit liners for wood burning fireplaces. Please follow the below links. Hargrove Replacement Firep...
Our Answer: It will not. Your DFX32NVC requires either a BLOT or FK-180. Please view both of these by following the below links. BLOT [1] FK-180 [2] From Page: CUI-BLOTSC [3] Manufacturer's Product Number: BLOTSC Our SKU: BLOTSC Page ID: cui-...
Our Answer: Occasionally, a strong downdraft can cause smoke to back puff from these stoves. Due to the way they are constructed it is rare for this to happen, but if the wind is blowing in a direction it normally does not, you can get smoke intrusio...
Our Answer: This type of infrared heater uses a very small, contained flame that heats the individual burner plaques that make up the element. Unlike a standard wall heater, this unit does not heat the surrounding air, but radiates heat directly onto...
Our Answer: No, you will need a much bigger propane tank that is installed outside your home to operate a propane fireplace. You may want to look into purchasing a 40-gallon tank or possibly renting a 100-gallon tank. From Page: CUI-VFD26FM30WP [1]...
Our Answer: This kit contains one single bag of 5 grams of platinum bright blowing embers. This is enough material to dress up log sets up to 42 inches. From Page: ACS-PBE [1] Manufacturer's Product Number: PBE Our SKU: PBE Page ID: acs-pbe ...
Our Answer: The full insulation fireboxes are useful and a wise choice if you are installing your unit on an exterior wall in your home. The insulation will keep the cold air from outside from coming into your home and hampering the performance of yo...
Our Answer: This mantel shelf will come with a wall cleat, but no hardware. You will need some masonry screws or fasteners to mount the wall cleat on your brick, then you will mount the mantel on the cleat. For more information, please refer to the i...
Our Answer: Depending on the size of the stove, it can take anywhere from 2-4 cans. If you can supply your dimensions, one of our fireplace specialists can give you a better estimate. From Page: CPF-42100 [1] Manufacturer's Product Number: 42100 ...
Our Answer: Yes, this item only consists of the two 24" W x 21" H mesh panels with rings and matching coil pulls. You would need to install a track on which these panels would attach and slide back and forth. In Response to Question: Hello. I ma...
Our Answer: Because of the fact that there are so many different shapes of damper, it is hard to say for sure that this would be a problem. It is doubtful that you would harm the brush in any way, as they are made to handle the abuse of cleaning a ch...
Our Answer: The Empire heaters will come with a build tag attached to the left front, the right front, or the rear panel. This tag will have the type of fuel the heater needs to operate. Unfortunately, this is really the only way to tell, other than ...
Our Answer: Many newer stoves are not capable of venting into a chimney system that is larger than their flue outlet. This is simply because new stoves are so efficient that they do not lose the necessary heat into the chimney that is required to mai...
Our Answer: They are indeed difficult to see, but the blower channels are built into the face of the unit, just inside the top and bottom of the surrounding outer frame. The channels have been kept to a minimum in size to maintain the clean faced app...
Our Answer: You are correct - you should be able to complete this repair if the right size damper plate was available. Unfortunately, our CPF-26265 (97-014) looks a bit small for your application. Sadly, it is the largest we carry. This unit would wo...
Our Answer: We do indeed offer venting kits for these direct vent appliances. For your appliance, you'll want to purchase 4"x7" venting components. Our venting kits generally consist of varying lengths of flex pipe and a termination. For example, che...
Our Answer: We have many options if you are looking for a hearth rug or extender, available in all kinds of styles and sizes. Please see our hearth rugs link for all of your options: Hearth Rugs [1] Here is a brief rundown of the materials used in so...
Our Answer: Fireplace inserts must be installed into either a masonry fireplace or an approved zero-clearance firebox. They are not designed to stand on their own. From Page: FSD-OB02401 [1] Manufacturer's Product Number: OB02401 Our SKU: OB024...
Our Answer: The Osburn 2200 insert actually measures a total of 28 3/8" from the back edge to the front grill. I hope this information is helpful. From Page: FSD-OB02201 [1] Manufacturer's Product Number: OB02201 Our SKU: OB02201 Page ID: fsd...
Our Answer: All of the dimensions, specifications, and capacities for these stoves are the same. The 1450 is simply a stripped down version of the 1400. The 1450 works in the same fashion, it simply is not as dressy as the 1400 nor does it offer as m...
Our Answer: Though it does not currently appear on our website, we do now offer the 7" DuraBlack stovepipe, so we would be able to get you the appliance adaptor, the pipe and the appropriate transition pieces to class A chimney pipe. Since the items ...
Our Answer: Please follow the below link to view a similar door in black. FMI 42 Inch Extruded Aluminum Bi-Fold Doors - Black [1] We recommend confirming with your owner's manual that these doors are right for your installation. From Page: CUI-BD4...
Our Answer: A reduced depth coal basket, such as this item, would be a fine choice for this type of application. Before installing something like this, it would be a good move to have the chimney inspected. Whether using a vented or vent free applian...
Our Answer: Please see the following link for the stainless tee support bracket for this DuraTech 6" stainless tee: DuraTech All-Fuel Stainless Steel Chimney Tee Support Bracket - For Chimney Tees with a 6-Inch Inner Diameter [1] From Page: CPF-706...
Our Answer: This unit carries a CSA certification, which allows it to be installed in all U.S. states as well as Canada. However, I do recommend checking with your local code office prior to purchasing the unit. They will have final authority on use ...
Our Answer: Unfortunately, Skytech does not have a way of programming their products to work with Logitech products or any other universal remote system. This was a question that has come up in the past, but Skytech advised that they use an RF signal...
Our Answer: You have two options for a blower, one is manually controlled while the other is thermostatically controlled. Please see them at the following links: BK (manual control): Vantage Hearth Squirrel Cage Manual Variable Speed Blower Kit [1] B...
Our Answer: You do not. Fireback boots are simply used to stabilize and raise the fireback if needed. It is entirely possible to use the fireback by just leaning it against the back wall. From Page: ADC-670320 [1] Manufacturer's Product Number: X...
Our Answer: I will be happy to assist you in locating the correct screen assembly. By your description, I am assuming you are looking for a screen that has built-in access doors, rather than a screen that you must move to access the fire. Also, is th...
Our Answer: This unit includes a faceplate and blower assembly. The only thing that you will have to add to complete installation is a chimney connector. Please visit the below link to view our selection of flexible chimney liners. Chimney Liners [1]...
Our Answer: A blower increases the circulation of heat generated by your fireplace, blowing the warm air out into the room. A blower like this item would only be intended for use inside a manufactured fireplace -- in this case a Napoleon NZ-26 model....
Our Answer: We do not have this particular rug in a 36" width. However, we do have the following rugs in that size. Please follow the below link. Napa Forge Textured Weave Large Leaf Hearth Rug [1] Napa Forge Textured Weave Scroll Hearth Rug [2] F...
Our Answer: A wood burning fireplace is a factory built, sheet metal type of box that needs to be installed into a wooden framed opening and finished out. A factory built metal chimney is then used to vent it. A wood burning insert is slid into a mas...
Our Answer: No, it is not made of wrought iron, but rather steel. The handles will screw on as well. Please see this comparable set, available in wrought iron: Woodfield Black Wrought Iron 4 Piece Fireplace Tool Set with Ring Handles [1] From Page:...
Our Answer: This fireback is 1.5" thick. Also, please note, the manufacturer has informed us that the correct dimensions for this fireback are 20.5" W and 23.5" H, not the 22" W and 20" H we currently show on the page. This mistake is being fixed. To...
Our Answer: This unit can not be purchased without the legs or pedestal. However, an insert version is available. Please view the below link. Timberwolf TI-2201 EPA Wood Burning Fireplace Insert with Flashing [1] A blower is available as an accessory...
Our Answer: For optimal efficiency, it will be necessary to line your existing chimney to the proper 3 or 4 inch vent this stove calls for. An unlined chimney will have a negative impact on the heating capacity of the stove. We will be happy to get t...
Our Answer: The part you mention, CPF-69880, is generally the Cathedral Ceiling Support Box that we recommend to customers that need to support triple wall pipe as it passes through their ceiling. We also have several different brands of triple wall ...
Our Answer: The main reason these are not recommended is due to the safety liabilities involved with gas logs. Top mounted dampers are easy to forget about and if the log set is operated with the damper closed, harmful byproducts can back up into the...
Our Answer: This is absolutely possible. However, to combine the venting of your 5" boiler and 3" water heater, you'll want your exhaust pipe to be 6" in diameter. Please find the Wye for this job here: Dura-Vent Type B Gas Vent Double-Wall Wye with ...
Our Answer: This unit is capable of a range heat output, from 15,000 to 30,000 BTU. This is sufficient for around 400 to 900 square feet. From Page: CUI-VSH30T [1] Manufacturer's Product Number: VSHN30T Our SKU: VSHN30T Page ID: cui-vsh30t ...
Our Answer: We have had no complaints about any of the sets we sell behaving in the manner you describe. Should any item prove to be defective in this way, it should be covered under warranty for a period of 1 year, at least. From Page: UF-T51030PK...
Our Answer: This unit is capable of generating 70,000 BTU's at high burn, heating an area up to 2,000 square feet. Burn time is listed at 9 hours (low fire). You can find all this information and more on page 5 of the owner's manual, which you can fi...
Our Answer: This grate will be approximately 12 inches in depth. The casting process will cause a variance in size of up to a 1/2 inch. From Page: UF-C-1533 [1] Manufacturer's Product Number: C-1533 Our SKU: C-1533 Page ID: fsd-c-1533 Links:...
Our Answer: This sealant by Napoleon is not silicone based. Instead, it is Millpac. Millpac is comprised of high temperature elemental fibers and ceramic fillers that are encapsulated in a high temperature organic based resin. This sealant has a much...
Our Answer: We do not offer either the transmitter or the receiver for sale without the other. They are only sold as a kit. From Page: CUI-RCMT [1] Manufacturer's Product Number: RCMT Our SKU: RCMT Page ID: cui-rcmt Links: ------ [1] http:/...
Our Answer: This unit is a completely self contained model that does not have any provisions for a chimney. As such, it is not possible to vent this unit or control heat output beyond the adjustment on the gas valve itself. From Page: CUI-DFS32NVC ...
Our Answer: The frame of this screen sits directly on the hearth and is held in place by the support feet that are welded to either side of the frame. The screen must have something to lean back against, otherwise it would fall back into the fireplac...
Our Answer: Indeed, these Geo Shapes can be cleaned. Any cleaner recommended for use on ceramic gas logs should do the trick. Please follow the below link to view one of our options. Rutland Log Bright Gas Log Soot Remover [1] You may try relocating ...
Our Answer: It's totally up to you! Both the GZ550-1KT and the B440-KT are approved for the GD33NR. The economy B440-KT is not quite as powerful or as efficient as the GZ550-1KT but it will do the job just fine. From Page: NPL-GZ550-1KT [1] Manuf...
Our Answer: Most of our inserts do indeed have a 6" flue. The flexible liner is a good choice for venting our inserts. Especially, as you'll be venting through an existing chimney. We'd first recommend attempting to remove your damper plate, if possi...
Our Answer: This product is not insulated or weatherproofed for use on an exterior wall. As such, its use should be restricted to bridging a wall between interior rooms. From Page: CUI-VI368ST [1] Manufacturer's Product Number: VI368ST Our SKU:...
Our Answer: This item is made for use with Napoleon's GDI44 fireplace only. For our selection of fireplace doors that you may be interested in, please see the following link: Fireplace Doors [1] From Page: NPL-SK44-A [2] Manufacturer's Product Nu...
Our Answer: This particular kit only includes a handle and brush with rod. It is not set up to be used in conjunction with a drill for cleaning a dryer vent. You would simply need to sweep the brush back and forth through the vent until all deposits ...
Our Answer: We do have the color "Surf Sand" in this paint: Copperfield Surf Sand Fireplace Surround Paint [1] From Page: CPF-43405 [2] Manufacturer's Product Number: 6320 Our SKU: 6320 Page ID: cpf-43405 Links: ------ [1] http://www.efirep...
Our Answer: This unit does not come with any ceramic brick liner, and it is not required for use with this firebox and a ventless log set (which is also not included). Please see the "Accessories" tab on the item page for available options for liners...
Our Answer: Per the manual and as long as your fireplace is a 42" unit, yes. These doors will work just fine with your Bungalow fireplace. From Page: FSD-BD42B [1] Manufacturer's Product Number: BD42B Our SKU: BD42B Page ID: fsd-bd42b Links...
Our Answer: Yes, this cap is 316-alloy stainless steel. From Page: CPF-10460 [1] Manufacturer's Product Number: 10460 Our SKU: 10460 Page ID: cpf-10460 Links: ------ [1] http://www.efireplacestore.com/cpf-10460.html
Our Answer: The price listed is for the base unit, before any of the decorative facings, doors, etc. have been added. You must select a door, faceplate, grill, and keystone finish to complete the unit. Many different finishes are available and give a...
Our Answer: No, this unit must utilize FMI's 8" inner diameter air-cooled class A chimney pipe (outside diameter is 12 3/8"). We have this pipe and all necessary components available on the site, please see this link for example: FMI Wood Fireplace 8...
Our Answer: This vent kit is indeed available, and you can find it here: Empire DVVK3FV Innsbrook Direct Vent Gas Fireplace Vertical Vent Kit - 25 Foot [1] This venting kit is not included in the price for the Innsbrook insert. This kit includes 50 f...
Our Answer: If you have already checked the obvious issues - flue size, flue blockage, etc., then you may need to look into getting a smoke guard such as this: SmokeGuard 8 in. Smoke Rollout Eliminator in Black [1] We would recommend checking the own...
Our Answer: Empire says your problem may be alleviated by re-positioning the bulb to a cooler location. The tech says it is probably getting too hot too quickly and causing this problem. If you have already tried this, or you try and it and your prob...
Our Answer: Yes, this bellows features real leather. From Page: FSD-19634 [1] Manufacturer's Product Number: 19634 Our SKU: 19634 Page ID: fsd-19634 Links: ------ [1] http://www.efireplacestore.com/fsd-19634.html
Our Answer: That measurement is up to you. The corbels are shipped unattached from the mantel shelf. You have the option to place them in any location beneath the shelf you choose. You may also leave them off. From Page: PRM-412 [1] Manufacturer...
Our Answer: This woodburning fireplace would suit your application well. Please be aware, though, that when installing this fireplace combustible materials that protrude out from the face of the fireplace cannot be installed within 9" of the fireplac...
Our Answer: The manufacturer recommends that the interior of this particular unit be finished out with either fire brick, stone, or refractory mortar. I called them to check if refractory panels are recommended for use, but they advised against this....
Our Answer: Yes, it may. Here is what Napoleon says about such an installation in the owner's manual: Use the periscope kit to locate the air termination above grade. The periscope must be installed so that when final grading is completed, the bottom...
Our Answer: The replacement shoulder screws that attach the door handle assembly can be replaced and should alleviate this problem. The screws are part number W570-0048.Please give us a call if you would like to order these items. From Page: NPL-NZ...
Our Answer: This screen door accessory is designed to be used specifically with Napoleon's 1600C wood stove. From Page: NPL-EP90-K [1] Manufacturer's Product Number: EP90-K Our SKU: EP90-K Page ID: npl-ep90-k Links: ------ [1] http://www.ef...
Our Answer: Indeed, we do. We'll be able to ship this item immediately. From Page: CUI-ODG36WE [1] Manufacturer's Product Number: ODG36WE Our SKU: ODG36WE Page ID: cui-odg36we Links: ------ [1] http://www.efireplacestore.com/cui-odg36we.htm...
Our Answer: It is. Please view the circulating version of this unit at the link below: FMI Bungalow - Builder 42 Inch Circulating Wood Burning Fireplace [1] In addition to the unit, you will need to select one of the blower options from the accessory...
Our Answer: It is light gray to white in color. It is available in no other colors. This mantel would accept Napoleon's BGD36CFNTR. However, you would need to trim out the appliance to cover the gap between the fireplace and the mantel. From Page:...
Our Answer: Yes, this firepit is designed to house a 20 lb propane tank. It can be converted to use either propane or natural gas. From Page: COC-LACOSTA [1] Manufacturer's Product Number: LACOSTA Our SKU: LACOSTA Page ID: lagrfipata Links:...
Our Answer: A fire can be burned 30 minutes after the gasket is applied. It is recommended to burn a small fire immediately after the 30 minute mark in order to help the adhesive cure fully. Burning a large fire before the adhesive has cured will cau...
Our Answer: This particular product is designed for use with masonry or cemented joints only. It does not have the ability to bond to cast iron. We do carry a product that can be used to seal small cracks in a casting: Rutland Pre-Mixed Black Furnace...
Our Answer: Unfortunately, the RX05 controller is no longer manufactured. We only sell the Acumen remote assemblies as a matched remote/receiver package, such as the RCK-M shown above From Page: HPC-RCK-M [1] Manufacturer's Product Number: RCK-M...
Our Answer: This conversion kit is manufactured for specific Napoleon gas valves and is not likely to fit the Honeywell or SIT valves that are used in Majestic fireplaces. Unfortunately, your model of Majestic fireplace was made by the CFM corporatio...
Our Answer: This insert will work for your application. In fact, this will be your only option - it is the smallest unit that we currently offer. In Response to Question: hi, I have a very small fireplace and I am trying to figure out if this in...
Our Answer: You've made some good choices. However, this particular item has 1/4" threads. So, to use it with the Copperfield 5' fiberglass rods, CPF-2360-59F, you will need an adaptor. Our CPF-23709 would do the trick. You can view it here: Copperfi...
Our Answer: According to the manufacturer, this product has a width measurement of approximately 14 inches. From Page: ADC-800053 [1] Manufacturer's Product Number: X800053 Our SKU: X800053 Page ID: adc-800053 Links: ------ [1] http://www.ef...
Our Answer: This particular unit comes complete, less the class A chimney pipe that is needed for your installation. The fireplace is not configured for a blower and features a radiant smooth faced design. As long as you have the unit and chimney pip...
Our Answer: Any of Osburn's inserts would be incomplete without the door overlay kit, faceplate and faceplate trim. Orders shipped to Kentucky are free of sales tax. Our stoves and inserts are shipped via common carrier and are delivered to the curb ...
Our Answer: These doors are not air tight from the factory and are recommended for use in applications that will not expose them directly to smoke, as to prevent any leakage from occurring. While the door could be gasketed to give a tighter seal, I c...
Our Answer: Due to the high amount of insulation that goes into the high efficiency units, they do not have an overall measurement that is this small. The NZ-26 is the smallest of the closed combustion fireplaces that we carry. It would be necessary ...
Our Answer: We have quite a few wood burning fireplaces that would be able to take the place of your corner gas unit. Our NPL-NZ-26 is, indeed, one of these. Special allowances will need to be taken into consideration when framing in this unit. Pleas...
Our Answer: While this is not an item we have listed for individual sale, we can special order the door for you. It will fit if the casting on the unit is not the older style. What is the serial number for the unit? What will be the color of the door...
Our Answer: You will most likely be interested in this product: Simpson DuraLiner 24 inch Rigid Reline Pipe - 6 inch Diameter [1] It is a rigid, insulated chimney reline pipe that would be ideal for your installation. We also offer this product in 3 ...
Our Answer: The unit that this kit is designed to work with is 37" wide by 36" tall. You may be able to modify the height of this kit to make it work for your application, but because of the fact that you will not be using it with the GD70, I cannot ...
Our Answer: You are correct. At one time, FMI offered this unit as a B-vent/Direct Vent convertible model. It is shown in the photo as a B-vent conversion. The direct vent model that we currently offer would have the sealed glass window and coaxial v...
Our Answer: This MetalBest Ultra-Temp 6 Inch Diameter Chimney Pipe Firestop/Joist Shield is not a part of a chimney system for venting exhaust, but it does support the pipe as the pipe passes through the floor. From Page: CPF-77916 [1] Manufactur...
Our Answer: The difference between Napoleon's two cabinet styles is depth. The flush cabinet is only 8" deep. The flat cabinet is 28" deep. From Page: NPL-MBMF [1] Manufacturer's Product Number: MBMF Our SKU: MBMF Page ID: npl-mbmf Links: --...
Our Answer: This shelf comes with a wall cleat for installation. You would mount the cleat onto your stone wall and the shelf would then hang from it. No mounting hardware is included. From Page: PRM-412 [1] Manufacturer's Product Number: 412-24...
Our Answer: The following information is from Empire: The return depth on this mantel is only going to be about 3/4". It is made with 1/2-inch cabinet-grade plywood construction with real hardwood moldings. From Page: CUI-MFL52UH [1] Manufacture...
Our Answer: The "track mount" refers to the screen track that is built into many manufactured fireplaces. If you have a metal firebox, it will most likely have a channel built into the top of the box that allows the screen panels to slide back and fo...
Our Answer: We are located in Memphis, TN and do not have any locations in that area. However, shipping on orders over $99 are indeed shipped for free so the sale price would be your final price. We also do not charge tax on orders shipped to that lo...
Our Answer: The manufacturer says that measurement is approximately 7.5". From Page: UF-S-1096 [1] Manufacturer's Product Number: S-1096 Our SKU: S-1096 Page ID: fsd-s-1096 Links: ------ [1] http://www.efireplacestore.com/fsd-s-1096.html
Our Answer: Everything you need to convert from propane to natural gas will be included with this kit. Please note that this kit is only for the 36" Solitaire Direct Vent fireplaces with Signature Command Controls. From Page: MAJ-BLCK400CKNS [1] ...
Our Answer: Perhaps you'd be interested in one of our variable flame ventless log sets - take a look at the below link. Per your room dimensions, the maximum allowable BTU would be around 60,000 (assuming 8' ceilings). Please note that the below log ...
Our Answer: We have this item that may interest you: Woodfield Hanging Fireplace Spark Screen Rod Kit [1] From Page: FSD-RMP2417 [2] Manufacturer's Product Number: RMP2417 Our SKU: RMP2417 Page ID: fsd-rmp2417 Links: ------ [1] http://www.ef...
Our Answer: This unit does indeed come with screening that is installed on all sides of the fireplace. You will also have your choice of styles for the screening as well. The current designs that are offered can be seen in the drop down menu on the i...
Our Answer: For any vent free appliance, the first part that comes to mind as the potential cause of your complaint would be the ODS pilot assembly. For a natural gas SR18T, this would be part number R-6307. Of course, this is solely a guess and we r...
Our Answer: This is indeed one of the better outdoor linear burners on the market. HPC has refined their linear burner series and added new ignition controls recently and an improved gas valve. The unit is supplied with lava rock, which the manufactu...
Our Answer: 1. From the owner's manual: MINIMUM MASONRY OPENING Height 23 1/8" (587 mm) Width 28" (711 mm) Depth 18" (457 mm) 2. No, it does not. This insert requires a 6" stainless steel liner, which we offer. Depending on the height of your chimney...
Our Answer: Generally, a conversion can be done by using a different style of burner pan or a retrofit kit. However, I am uncertain if Heat N Glo has a unique conversion kit for this procedure. I would highly recommend contacting a Heat N Glo dealer ...
Our Answer: While you can use this paint for the inside of a woodburning firebox, please be advised that the heat and possible flame contact will eventually cause the paint to peel. We offer no paint that can resist this inevitable result, but paint ...
Our Answer: Per your dimensions, we'd recommend the below "basket-style" fireplace grate. G1000 Series 24 1/4 in. 'Basket Style' Cast Iron Fireplace Grate [1] From Page: HYC-G1028-4 [2] Manufacturer's Product Number: G1028-4 Our SKU: G1028-4 ...
Our Answer: Unfortunately, we do not offer custom-made blowers. This blower is for use only in certain FMI woodburning fireplaces; it is not for inserts. In Response to Question: I have a fireplace insert. The opening is beneath the door causing...
Our Answer: Unfortunately, there is no matching stovepipe available for the Porcelain Sand. While we do carry some gas vent pipe spray paint, none of the colors we offer will provide an exact match to this color. From Page: CUI-DVP30CA30BN [1] M...
Our Answer: This unit is made as a visual effect model only. Napoleon does not currently offer an optional heater for this model. From Page: NPL-EF39S [1] Manufacturer's Product Number: EF39S Our SKU: EF39S Page ID: npl-ef39s Links: ------ [...
Our Answer: Unfortunately, not. The twist-lock components of each of these brands feature proprietary designs and are not compatible with each other. From Page: CPF-68620 [1] Manufacturer's Product Number: 6GVL45 Our SKU: 6GVL45 Page ID: cpf...
Our Answer: This unit is designed to be operated at your leisure and will not be damaged if it remains off during stove operation. As a result, a power outage would not affect it. From Page: USS-MH6 [1] Manufacturer's Product Number: MH6 Our SK...
Our Answer: Unfortunately, we do not have a full, accompanying bookcase to go with this insert and cabinet. The closest alternative would be an entertainment center, like this item: Classic Flame Brookfield Media Center with Electric Fireplace - Prem...
Our Answer: Unfortunately, we do not have the manufacturer-specific panel that you are looking for, but we do offer some universal refractory panels that will work for your woodburning fireplace. Please see the following links: One 24\"h x 28\"w Pane...
Our Answer: IAll of the Viper products come standard with a M10 size connection. This is true also for the brushes. If your current rods have this type of connection, then this brush will work for you. From Page: CPF-442-POLY [1] Manufacturer's P...
Our Answer: You may use whatever surround you like with our Tahoe fireplaces. You'll just want to confirm dimensions on that surround. This fireplace features dimensions of 43 3/8" wide by 34 3/4" high. From Page: CUI-DVX42FP33CLN [1] Manufactur...
Our Answer: This unit is able to be installed on combustible flooring and combustible flooring can be run up to the base of the fireplace without a problem. If you wish to install drywall in close proximity to the fireplace, it will be necessary to l...
Our Answer: Ideally, you want the ratio of your fireplace opening to flue size to be 10:1. In order to purchase the correct rollout eliminator, you would need to calculate the number of square inches of your opening, in comparison to your flue, then ...
Our Answer: Please allow us to check with the manufacturer regarding availability of a replacement panel for this unit. If it is available, it will take about 4-6 weeks to ship to you. If you are still interested, please reply with your shipping zip ...
Our Answer: This rug is made of 100% wool. So, any fabric cleaner approved for this application should work just fine. Of course, we recommend trying any cleaning product in an inconspicuous are to avoid adverse effects. From Page: FSD-10313 [1] ...
Our Answer: Depending on the fault the RF system is indicating, bypass of the system may not cure the problem you are having with the unit. The system has an LED indicator light that will flash a number of times to indicate the problem. Please advise...
Our Answer: Unfortunately, not. This unit is not made to stand up to the corrosive nature of the great outdoors. We currently only have one unit that provides this option. Please follow the below links to check out this fireplace and its stainless st...
Our Answer: This item is indeed unfinished and is designed to be stained prior to installation. The primed mantel you're noticing may simply be our advertisement for similar items to this mantel. This ad is displayed once you add the unfinished versi...
Our Answer: This unit could be installed into a wood burning fireplace. However, no surround or flashing kit is available. So, mounting the unit into a wall and finishing it with drywall is a much easier installation option. From Page: FSD-36EB111-...
Our Answer: I'm sorry, but we do not offer an adaptor such as you describe. You could either try to run L-vent (pellet vent) pipe through this pipe, if feasible (our 3" PelletVent Pro pipe has an outside diameter of 3 5/8"), or have something fabrica...
Our Answer: It is not recommended to use a log lighter such as yours with this application. While you may have enough room to fit it under the grate--depending on your application--your log lighter may have to be completely removed for this item to f...
Our Answer: This rug meets the federal standard DOC-FF-1-70 requirements for surface flammability. It will protect your floor from sparks and embers, but it has not been tested with full pieces of coal. The sparks and embers may leave burn marks on t...
Our Answer: Ceramic liners, such as this model, are manufactured specifically for use with the particular fireplace line that is listed. That being the case, they can generally not be used with other models. The ceramic liners are not able to be modi...
Our Answer: This does not include the mantel. Please see one of the available mantels for this unit here: Vantage Hearth 26 Inch Traditional Medium Oak Wooden Wall Mantel [1] You can see all of them by entering "Vantage Hearth 26 Mantel" in our searc...
Our Answer: Yes, custom dating is available. While these units are standardly produced with the current year, we may have them cast with any date you wish. There would be a custom casting fee of $125 and a lead time of 6 to 8 weeks associated with th...
Our Answer: This type of stove pipe is rated to 2,100 degrees and is indeed compatible for most boiler applications. It has a life expectancy of 25 years when used with most boilers. The manufacturer of the boiler will have final say on what type of ...
Our Answer: This Monessen DFX24C is indeed a complete fireplace system, with the burner and logs included with the firebox. It does not come with the ceramic brick liner you see in the picture, that is available in the "Accessories" tab on this page....
Our Answer: This remote is designed to be used with fireplaces that feature a Signature Command control system. Any remote for millivolt appliances should work fine for your application. Please follow the below link to view a remote more appropriate ...
Our Answer: The only required additional purchase would be the proper vent pipe for this direct vent fireplace. We have some vent kits available, depending on if you want to vent this unit vertically or horizontally. This fireplace uses the Simpson D...
Our Answer: Either of the following remotes are designed by Empire to be used with this unit: Empire Battery-Operated Remote Control [1] Empire Battery-Operated Remote with Thermostat Control [2] You may also utilize a wall thermostat with this unit,...
Our Answer: While Bio Flame has released other models of fireplace that allow you to choose between fuel cans and a fuel tray, they have not yet offered the option for this model. Since this is still a fairly new unit, I anticipate that they will be ...
Our Answer: This particular unit is non-insulated, however we can order an insulated model from the manufacturer if needed. Both the non-insulated and insulated versions are set up from outside combustion air from the factory. The outside air kit wil...
Our Answer: The first step would be to consult a plumber about the cost estimate and viability of running a gas line to your fireplace. Different factors may make the installation easy or nearly impossible. Running a gas line into a manufactured (met...
Our Answer: This insert you inquired about, as with all fireplace inserts, are made to slide into existing masonry fireplaces/chimneys. We did also receive your other email asking about inserts in general, and this is the case for all fireplace inser...
Our Answer: This unit is actually shown installed into an optional mantel that is not included with the firebox itself. We offer the following models of mantel to fit the unit: Vantage Hearth 21 Inch Traditional White Wooden Corner Mantel [1] Vantage...
Our Answer: The only thing you need to add to this fireplace to allow it to circulate heated air is a blower. We have two different options. You may find them by selecting the Accessories tab on this item's webpage. Vantage Hearth Value Line Series 3...
Our Answer: Due to the buildup of soot and ash, it is advisable to only use this fireplace outdoors on an unenclosed patio or porch. The only situation this could be overlooked is if gel fuel cans were burned in the unit for aesthetic purposes. Fr...
Our Answer: The tops of the direct vent gas stoves are not going to get hot enough to do anything other than warm a kettle of water; you would never be able to boil it. The kind of heat you would need would only come from a woodburning stove, like th...
Our Answer: Unfortunately, there is no screen included with the fireplace, nor does Napoleon make a screen for it. From Page: NPL-HD81NT [1] Manufacturer's Product Number: HD81NT Our SKU: HD81NT Page ID: npl-hd81nt Links: ------ [1] http://...
Our Answer: In a word, yes. However, it requires the addition of the SCSACM control module. Monessen's BDV 300 can use two blowers. Either this unit or the BLOT.. You may find this other blower by following the below link. Monessen Variable Thermosta...
Our Answer: Technically, neither. The 500DVBLNV accepts the MAJ-FBBLDV500TB. It can be found at the below link. Majestic Tavern Brown Firebrick Wall and Hearthbrick Kit - For 42 Inch Solitaire Direct Vent Gas Fireplaces [1] From Page: MAJ-FB400W10B...
Our Answer: Galvanized and galvalume are the same and will be susceptible to rust and corrosion if exposed to the weather. Stainless steel will not rust or corrode and therefore is strongly recommended for any use where your pipe will be exposed. How...
Our Answer: First, let me clarify that this is a woodburning fireplace, not a direct vent unit like your Heat N Glo. Being a woodburning unit, you will need to have a class A chimney pipe system venting vertically and terminating at least 3 feet abov...
Our Answer: Due to the sensitive nature of a vent free system, it is not recommended to use these embers. The only embers that can be utilized are the embers provided with your system or any embers that are sold as an accessory in the manual that cam...
Our Answer: We do not. Arched hoods are something that would be best received from a custom fabrication shop. From Page: FSD-EUCH6S [1] Manufacturer's Product Number: EUCH6S Our SKU: EUCH6S Page ID: fsd-euch6s Links: ------ [1] http://www.ef...
Our Answer: The wall cleat for mounting this mantel shelf is indeed included. From Page: CUI-MS48PG [1] Manufacturer's Product Number: MS-48-PG Our SKU: MS-48-PG Page ID: cui-ms48pg Links: ------ [1] http://www.efireplacestore.com/cui-ms48pg...
Our Answer: This brush features a 3/4" loop on one end and a 3/8" pipe thread on the other. Our quick connects allow for the rapid connecting/disconnecting of chimney cleaning rods and brushes. Please follow the below links to view them. Copperfield ...
Our Answer: Unfortunately, these doors do not come with a lock. However, a locking clasp could be added to them by attaching it to the top or bottom door rails. I apologize that this item does not already come with a lock as an option. From Page: C...
Our Answer: The 8" inner diameter Majestic triple-wall type "S" pipe has an outside diameter of 13 3/8". From Page: MAJ-84 [1] Manufacturer's Product Number: 84 Our SKU: 84 Page ID: maj-84 Links: ------ [1] http://www.efireplacestore.com/ma...
Our Answer: The height of this cast iron fender at its tallest point is 5 1/4". The "spikes" are about 1" above the top horizontal bar, so that part measures about 4 1/4" high. From Page: PTS-FF04-24 [1] Manufacturer's Product Number: FF04-24 ...
Our Answer: These Plazmafire's can indeed be used with a remote. You can find our two most popular options by following the two links below: F45 [1] F60 [2] From Page: NPL-WHD31 [3] Manufacturer's Product Number: WHD31N Our SKU: WHD31N Page I...
Our Answer: This brush features a thread dimension of 1/4". From Page: UF-BRU-T5 [1] Manufacturer's Product Number: BRU-T5 Our SKU: BRU-T5 Page ID: fsd-bru-t5 Links: ------ [1] http://www.efireplacestore.com/fsd-bru-t5.html
Our Answer: Unfortunately, we do not carry a longer escutcheon that would make up the now larger gap to the valve. I have had some customers in the past mention finding a nylon "extender" that is designed to lengthen the shaft, but I have not located...
Our Answer: According to FMI tech, this unit was manufactured in the early 90's by a proprietary company that built some FMI units. The unit uses a pair of 5" flexible vents, side by side. They also require a unique firestop and termination. These pa...
Our Answer: This particular item will include the firebox itself, along with the mesh pull screens and fireplace grate. It will be necessary to purchase the needed flue pipe, as well as a blower and doors, if you want to add them. All available acces...
Our Answer: The sides of this mantel cabinet should touch the wall in the same way that the top does. The top shelf does indeed overhang the cabinet on both sides and in the front. However, it sits flush on the back edge. As such, these units do not ...
Our Answer: The GD19N Vittoria fireplace ships as a top vent, but it can be converted to a rear vent. Please see page 22 of the owner's manual (can be downloaded on this product page). From Page: NPL-GD19N [1] Manufacturer's Product Number: GD19...
Our Answer: Interior dimensions are approximately 33 1/2 inches wide and 23 3/8 inches tall. The surround has a 6-inch boarder thickness on all sides. While it is designed for use with the Empire Large Innsbrook Fireplace Insert, it could be adapted ...
Our Answer: The standard unit with the reed switch is a low voltage model that uses a simple mercury switch for operation, much like an older HVAC thermostat. A supply and return wire would need to be run to the unit for the thermostat to work. The o...
Our Answer: The pot is rated at a 2 gallon capacity and is rated to hold about 15 pounds, per Napoleon. It is designed to be used specifically with the NZ6000 fireplace and does not come with hardware to be used with any other unit. Hardware is pre-a...
Our Answer: Your thoughts are correct. Our universal fit replacement brick panels would do the trick. Your other option would be to locate the model of the fireplace and order the specific replacements for it. This information can be found on the dat...
Our Answer: It does not. That item can be found by following the below link. Napoleon GD70 Gas Fireplace Faceplate-Door Kit with Upper and Lower Ornamental Insets [1] From Page: NPL-GD70-1SE [2] Manufacturer's Product Number: GD70NT-2SE Our SKU...
Our Answer: This surround measures 37" wide and 23.5" tall. From Page: CUI-DF28GBL [1] Manufacturer's Product Number: DF-28-GBL Our SKU: DF-28-GBL Page ID: cui-df28gbl Links: ------ [1] http://www.efireplacestore.com/cui-df28gbl.html
Our Answer: As you know, this item is a woodburning fireplace. Please see these see-through gas units that you may like: Napoleon GVF40 Multi-View Vent Free Gas Fireplace [1] Empire Tahoe Premium Direct Vent Natural Gas See-Thru Fireplace - 36 Inch [...
Our Answer: The only difference between these two items is the black wrought iron will come with a matte black finish that has been applied by the manufacturer, while the vintage iron will not. The vintage iron screen will retain the natural, dark gr...
Our Answer: The plug for this tee is actually designed for the bottom only. It can be easily removed for cleaning or access to the chimney for inspection. From Page: CPF-77898 [1] Manufacturer's Product Number: 6T-IT Our SKU: 6T-IT Page ID: c...
Our Answer: This unit's manual lists installation above 4,500 ft as a potential risk of pilot outage. However, depending on your local gas supply the unit may run just fine. Some gas companies at higher elevations amend their gas supply for their con...
Our Answer: This surround that you have inquired about is made only for use with the Empire Medium Innsbrook Fireplace Insert. For that reason, the chances of this surround working for your stove right out of the box are slim to none. Most surrounds ...
Our Answer: This particular model of fireplace does not come with gas logs or a burner assembly. In order to see the vent free units that come with logs, please visit the link below: Vent Free Fireplaces [1] Within this section, you will see about 4 ...
Our Answer: Please see this tool set, which has a height of approximately 39": Pilgrim 5 Piece Large Vintage Iron Fireplace Tool Set [1] From Page: FSD-18002 [2] Manufacturer's Product Number: 18002 Our SKU: 18002 Page ID: fsd-18002 Links: -...
Our Answer: All of the blowers we offer are all brand specific. This particular unit is compatible with several Majestic and Monessen appliances. Due their specificity, we do not list individual blower measurements. The best course of action is to de...
Our Answer: An electrician may indeed be able to remedy the issue, as the electric inserts made by Twin Star are fairly simple. The most common thing to go out is the drum motor, which is a fairly universal part that can be serviced in field. If it i...
Our Answer: Each of these options would require either drilling into the granite front or the concrete lintel. Surface mounts are just that - they feature a mounting bracket that would be screwed right into the fireplace front. Our lintel mounts atta...
Our Answer: Each fireplace model requires a different conversion kit. Model number and sometimes even a serial number is required to determine the correct conversion kit. This can generally be found on the fireplace's data plate. Data plates are gene...
Our Answer: Unfortunately, we do not offer a stainless steel door for this unit. Moreover, this unit is not truly designed to be installed outdoors - even halfway. The steel body of the fireplace is simply not made to withstand the corrosive nature o...
Our Answer: This can be accomplished by resetting the transmitter. After depressing the reset button inside the battery door, simply press the "On" button to cycle between degrees Celsius and Fahrenheit. From Page: CUI-RCSTEBA [1] Manufacturer's...
Our Answer: Unfortunately, this particular item would be a bit too small for your needs and the next size up would be too large. It sounds as if your damper is designed like most common, cast iron damper plates, so finding a correct replacement would...
Our Answer: If you do indeed have the Santa Fe by FMI, the unit can only be used with the log set that it is shipped with. The unit uses a unique, "X" shaped burner that is specifically configured for logs only. Given that this is a direct vent firep...
Our Answer: While it seems like this may be a good product for the problem you are having, please give us a call to discuss at 1-800-203-1642. From Page: CPF-13130 [1] Manufacturer's Product Number: 13130 Our SKU: 13130 Page ID: cpf-13130 Li...
Our Answer: While this manufacturer does not have a specific boot set to fit this model, the CPF-61097 is an acceptable alternative that can be used with the fire back. Due to the thickness of this model of fire back, it will be relatively vertical i...
Our Answer: The hold is sturdy, it is made of wrought iron. The overall weight of this item is about 20 lbs. The longest tool will be the shovel, which is 23 5/8" long. The other tools will vary between approximately 19"-23". From Page: UF-W-1052 ...
Our Answer: This cast iron surround is specifically designed to be used with Napoleon fireplaces. However, it features an adjustable width measurement. It's interior opening dimension can be as narrow as 28.5" and as wide as 41.5". It's interior heig...
Our Answer: This hood is designed to mount into the lintel on your fireplace. Please see the owner's manual for an illustration. The owner's manual can be downloaded on this product page. The kind of hood you are looking for is a surface mount. Pleas...
Our Answer: The valve could possibly be defective. Could you please reply with the model number of this control device so that we can research your question further? In Response to Question: I have a Hargrove Remote Cortrol Gas Jet Turn-on and Of...
Our Answer: This fireplace does not come with a blower, but you can certainly add one. Here is the blower for this unit: Majestic BLOTBLDVSC Signature Command System Dual Forced Air Fireplace Blower [1] From Page: MAJ-WDV500NTSC [2] Manufacturer'...
Our Answer: The base of this item measures 12" by 6". From Page: FSD-18015 [1] Manufacturer's Product Number: 18015 Our SKU: 18015 Page ID: fsd-18015 Links: ------ [1] http://www.efireplacestore.com/fsd-18015.html
Our Answer: While it is recommended that only R.H. Peterson logs be used with this burner system, it is possible to use other manufacturers of log on this type of vented burner. It is important to note however that the warranty for the burner will no...
Our Answer: You would indeed be able to utilize the thermodisc from this kit for your needs, however it will require a bit of modification to attach it to the inside of the blower housing. All but the earliest Osburn 2400 models came equipped with a ...
Our Answer: It is recommended that only one surround be installed at a time. If you'd like to reply with your fireplace's model number, we'd be happy to see if any of our surrounds are compatible. From Page: CUI-DF36M4BL [1] Manufacturer's Produ...
Our Answer: This rug does not have a backing per se; both sides are fiberglass. You may be interested in purchasing one of our non-skid pads for your new rug. Please follow the below link to view this item. Goods of the Woods Non Skid Pad for Hearth ...
Our Answer: This unit cannot be safely installed into a wall for a see-thru application, however we do carry a version of this unit that is a true see-thru model. Please see this unit at the link below: Breckenridge Premium Vent-Free See-Thru Gas Fir...
Our Answer: This grate is indeed cast from one solid piece and is ready for installation with no assembly. From Page: HYC-G800-27 [1] Manufacturer's Product Number: G800-27 Our SKU: G800-27 Page ID: hyc-g800-27 Links: ------ [1] http://www.e...
Our Answer: Whether or not a vent free appliance will create a film depends largely on the air quality and volume in the home. If the appliance is burned in a humid environment, it can cause a gradual buildup of condensation on the glass which will d...
Our Answer: This damper is designed to be used with flues with an inside dimension of 61/4" x 11" to 8-1/8" x 12-1/8. If your 8 x 12 measurement is your inside dimension, then this damper should work well for you. From Page: CPF-12109 [1] Manufa...
Our Answer: A direct vent unit like this Tahoe can indeed vent and terminate either vertically or horizontally. Please see the owner's manual (starting on page 18) for more details on venting this unit. The owner's manual can be downloaded on this it...
Our Answer: This concern is reminiscent of one we see often when supply pressure to a gas appliance is too low. Using a manometer, confirm that you have a pressure of at least 11" of w.c.being supplied to the unit. From Page: CUI-BF20LP [1] Manuf...
Our Answer: Yes, this item has a total length of 25 inches. The kindling extension measures about 6". From Page: ENC-LR1b [1] Manufacturer's Product Number: LR1b Our SKU: LR1b Page ID: rerabyen Links: ------ [1] http://www.efireplacestore.co...
Our Answer: Your fireplace would likely take 36" doors. However, we will only be able to recommend a set of doors if you are able to provide the model number of your fireplace. Without this information, there's no way to know which doors will fit. ...
Our Answer: All of our trim kits are specifically made to fit particular fireplaces or inserts. If you'd like to reply with the model of your direct vent appliance, perhaps we'll be able to find a trim kit for you. In Response to Question: I am ...
Our Answer: This particular set is indeed manufactured out of powder coated steel bar. The approximate weight of the set is 21 lbs. From Page: FSD-19012 [1] Manufacturer's Product Number: 19012 Our SKU: 19012 Page ID: fsd-19012 Links: ------...
Our Answer: This kit contains the exterior termination cap, stove adaptor, and the pipe clamp. It does not include the flex liner. This is meant for use with 5" inner diameter aluminum liner, either flexible or rigid, which you will need to provide a...
Our Answer: Here are the specifications from the owner's manual for this fireplace: Weight: 385 lbs Height: 43 1/4" Width: 36 3/4" Depth: 26" These dimensions will include the 2 heat-activated blowers that are included with the fireplace. I will be s...
Our Answer: Unfortunately, this is the only way Napoleon makes this tool sets, with these different styles for the different sets. They cannot be mixed and matched. From Page: NPL-TS6 [1] Manufacturer's Product Number: TS6 Our SKU: TS6 Page I...
Our Answer: This gasket does indeed require cement. You may find a couple of these items by clicking the Accessories on this webpage. From Page: RUT-90 [1] Manufacturer's Product Number: 90 Our SKU: 90 Page ID: rut-90 Links: ------ [1] http...
Our Answer: Yes, you may install this fireplace into an existing home and use a set up that you described. You must follow the clearances and venting specifications for this fireplace, which are listed and detailed in the owner's manual, which you ca...
Our Answer: This thimble can only be adjusted down to a 6" thickness, so it would indeed be necessary to build the surrounding wall out or trim the sheet metal collars on the thimble down to a shorter length. From Page: CPF-77915 [1] Manufacturer...
Our Answer: Per the location of the blower and the rear channel, your unit should be circulating heated air. Of course, unless the stove is fully up to heat, it will not have the capability to heat the air it is circulating. From Page: SBI-DB03030...
Our Answer: Because of the fact that each manufacturer uses different means to attach their louvers, it is doubtful that the Empire product would be interchangeable with your Majestic fireplace. I have looked into the Majestic unit you have, but have...
Our Answer: This blower is designed to be installed into the confined space of one of our Napoleon appliances. It is not intended to be used as a universal blower. From Page: NPL-B440-KT [1] Manufacturer's Product Number: B440-KT Our SKU: B440...
Our Answer: This unit does not require a blower. Indeed, this option is not even available. Millivolt control simply speaks to the control valve for the unit. It features simple On/Off controls and the option to be controlled via remote. From Page:...
Our Answer: Peterson's vent-free log sets feature a combination burner-grate. The grate is incorporated into the burner assembly. No additional grate will be needed. From Page: PTS-CHASG10-16/18-ManualN [1] Manufacturer's Product Number: CHASG10...
Our Answer: After speaking to the manufacturer, they advise that these doors can be retrofitted to the 36ECMII, but will not fit the standard 36E. However, the original doors are still available and can be special ordered. The new part numbers are VD...
Our Answer: This unit would be provide supplemental heat to an area of about 600 square feet. Additional components needed would be one of the following surrounds: Empire Contemporary Black Steel Fireplace Insert Surround - For Small Innsbrook Firepl...
Our Answer: Our NPL-TB636 is designed to work specifically with Napoleon fireplaces. We currently do not offer generic trim kits. If you could please reply with your fireplace model, we may have a trim kit that would work for you. From Page: NPL-TB...
Our Answer: These blowers (and all blowers from Napoleon for that matter) have just two leads coming from their motor. One is designated for the thermodisc switch and the other is intended for a variable speed switch. Leads from these switches would ...
Our Answer: Much like the receiver portion of the remote controls, this wall switch must be wired to the burner's control valve. From Page: PTS-POG45-24-APK-17P [1] Manufacturer's Product Number: POG45-24-APK-17P Our SKU: POG45-24-APK-17P Pa...
Our Answer: Many gas appliances are not compatible with remote controls. If you'd like to reply with your fireplace's model number, we'd be happy to search for the proper remote for it. In Response to Question: What kind of remote would I be abl...
Our Answer: You'll need two items. An adaptor and a vent pipe. Please follow the below links to view them. Fresh Air Adaptor for Osburn High Efficiency EPA Woodburning Stoves [1] Insulated Pipe for Osburn Fresh Air Adaptor [2] Generally, you'd pipe t...
Our Answer: This replacement hood mounts in place of the Breckenridge's standard hood. There are mounting screws on the inside top and sides of the firebox's perimeter. This hood extends 2" further than the standard Breckenridge hood. From Page: C...
Our Answer: This unit's stabilizing feet protrude both to the front and back. From Page: FSD-19254 [1] Manufacturer's Product Number: 19254 Our SKU: 19254 Page ID: fsd-19254 Links: ------ [1] http://www.efireplacestore.com/fsd-19254.html
Our Answer: This particular oval liner has an O.D. measurement of 10 3/4 inches on the long side, so it would fit your application. This is an excellent product for longer chimney relines, due to its factory insulation and sturdy double wall construc...
Our Answer: The stainless steel and ceramic facing kit that is used on an outdoor application does a very good job of insulating the unit and will be comparable to a high quality triple pane window in keeping cold air out of the home. I cannot say th...
Our Answer: Circulating describes a fireplace that can have a blower installed. Smooth faced or non-circulating units cannot use blowers. These fireboxes are large enough to accept any of our see-through Peterson vent-free log sets. You can take your...
Our Answer: While the overall height of this grate is 8", it only has a clearance height of 3". The Pilgrim 10-Bar grate may be a better option for you. Please follow the below link to check out this item. Pilgrim Ten-Bar Steel Fireplace Grate with C...
Our Answer: Unfortunately, not. We currently only ship to the US and Canada. From Page: NPL-WHVF31N [1] Manufacturer's Product Number: WHVF31N + S31RK Our SKU: WHVF31N + S31RK Page ID: npl-whvf31n Links: ------ [1] http://www.efireplacestor...
Our Answer: This hood is manufactured with a piece of metal facing straight back into the fireplace, in order to secure it to the lintel. It is possible to use a sheet metal brake to bend this piece of metal vertical. It could then be secured to the ...
Our Answer: The windbeater cap can indeed work for twist lock style pellet pipes that are terminated vertically. Because of the fact that this cap is crimped along the bottom, it will simply slide down into the pellet pipe. You will need to secure th...
Our Answer: No, these doors must be purchased complete. We apologize for the inconvenience. From Page: FSD-BDB36B [1] Manufacturer's Product Number: BDB36B Our SKU: BDB36B Page ID: fsd-bdb36b Links: ------ [1] http://www.efireplacestore.com...
Our Answer: For the most part, the difference in priced is based on the material with which each is manufactured. Napoleon's 1100C is a cast iron stove, while this Timberwolf 2100 is made of various gauges of steel. Also, the 1100C has 110 lbs of bri...
Our Answer: This unit does indeed require a glass front or door to complete installation. This item is a solid pane of ceramic glass with either a painted black, stainless steel, or gold-plated perimeter. However, the arched front with screen door ki...
Our Answer: This item does have welded prongs that are designed to hold the candles in place, should the holder be struck or moved accidentally. From Page: ADC-304135 [1] Manufacturer's Product Number: X304135 Our SKU: X304135 Page ID: adc-30...
Our Answer: Actually, the correct fireback supports for this fireback can be found here: Black Wrought Iron Fireback Supports [1] Please disregard the item title on that page, as those are indeed Black Wrought Iron Fireback Supports, and NOT andirons...
Our Answer: The longest bellows that we currently offer measure 25" in total and can be seen at the following link: Copperfield Long John Pine Bellows [1] These will supply enough air for most large wood and coal burning fires. From Page: CPF-61072...
Our Answer: I contacted Majestic's technical department regarding your conversion. Per the tech I spoke with, there is no available conversion kit for this fireplace. I apologize for the inconvenience. In Response to Question: I have a CFM Inc. ...
Our Answer: Installation of a smaller wood stove will generally run between $800 to $1500 dollars in labor costs. The exact figure can vary greatly, depending on the amount of chimney pipe that must be installed, labor rates in your area, and any str...
Our Answer: This is indeed the closest sized damper plate that we carry and would almost be a direct fit replacement for your application. From Page: CPF-26260 [1] Manufacturer's Product Number: 97-013 Our SKU: 97-013 Page ID: cpf-26260 Link...
Our Answer: The approximate burn time for this stove is 10-12 hours. This will vary depending on numerous factors, most importantly the quality of the firewood, draft, and the location/insulation of your home. From Page: FSD-OB02411 [1] Manufact...
Our Answer: Unfortunately, not. We currently only offer this item with the 30' of cable. We do offer an extra hardware pack. You may view it by following the below link. Lock-Top Installation Cable Pack [1] From Page: CPF-09507 [2] Manufacturer's...
Our Answer: No. While decorative filigree panels for this model are optional, the unit will come standard with the matte black louvers that are shown on the item page. From Page: MAJ-CDVR36NSC7 [1] Manufacturer's Product Number: CDVR36NSC7 Our ...
Our Answer: Per the manufacturer, this grate is both 30" wide and 30" deep. From Page: UF-C-1549 [1] Manufacturer's Product Number: C-1549 Our SKU: C-1549 Page ID: uf-c-1549 Links: ------ [1] http://www.efireplacestore.com/uf-c-1549.html
Our Answer: Thank you for your input. Napoleon is a quality manufacturer and we are proud to be an authorized dealer of their products. From Page: NPL-1450 [1] Manufacturer's Product Number: 1450 Our SKU: 1450 Page ID: npl-1450 Links: -----...
Our Answer: Per the manufacturer, this blower measures a very compact 8" long, 3" tall, and 3" deep. The CFM output of this model is 55 and it draws 20 watts at full speed. From Page: NPL-GS66 [1] Manufacturer's Product Number: GS66 Our SKU: GS...
Our Answer: Almost all of Napoleon's direct vent units can utilize the GPV power vent kit, but each fireplace will require an adaptor in addition to the kit. For example, this model, the GD36NTR, will require the PVA36 adaptor in addition to the GPV ...
Our Answer: This unit has a steady state efficiency rating of 67 percent, although use of a blower can increase efficiency rating of up to 2 percent. Napoleon's linear fireplaces are definitely the most efficient direct vent models that we offer curr...
Our Answer: These surrounds are made to fit precisely around Napoleon models GI3600, GI3016, GDI-30, NPI40, and NPI45 and may not achieve the function you desire. Are you just wanting to frame your opening with these? If so, please advise and I will ...
Our Answer: The BTU output of this firebox will depend solely on the log kit you choose to install into it. Most 18" vent free log sets that fit this model produce between 20 to 35 thousand BTU's. Actual output will depend on the overall efficiency o...
Our Answer: We are glad to build a chimney quote for you. We even have a quote form that you can complete and submit. Please follow this link to view our chimney quote form. Chimney Pipe Design & Quote Form [1] The prices listed online are the best p...
Our Answer: The chimney in the picture features a clay flue with a brick surround. The juncture between the flue and the brick is sealed with mortar or cement. This wash can be made from a tub of our Castable Cement. Please find our cement by followi...
Our Answer: Generally, these fireplaces are installed level with the floor. However, it is perfectly acceptable to build up a hearth area to raise the fireplace. The raised hearth can simply be made of framing materials designed to support the weight...
Our Answer: Indeed, this RTV is a great option for your needs. Please follow the below link to view the manufacturer's spec sheet for this item. http://www.rutland.com/back/tds/document_28.pdf From Page: RUT-76RT [1] Manufacturer's Product Number...
Our Answer: This burner features a set, non-adjustable air shutter that pulls in oxygen to be mixed with the supply gas. From Page: PTS-OCBE-34P [1] Manufacturer's Product Number: OCBE-34P Our SKU: OCBE-34P Page ID: pts-ocbe-34p Links: -----...
Our Answer: None of the inserts that we carry utilize outside air for combustion. The combustion chamber of a wood burning insert is very compact and as a result, does not usually need outside air for combustion. The unit draws only a very small amou...
Our Answer: Like most of our chimney pipe, Majestic pipe uses locking tabs to keep its individual components held together. The pieces are pressed firmly together and then twisted a quarter turn clock-wise to be locked. If you'd like help building a ...
Our Answer: The fan/blower kit is optional with this freplace. You may find the options available on the accessories tab of the main item page. From Page: FSD-C36LH [1] Manufacturer's Product Number: C36LH Our SKU: C36LH Page ID: fsd-c36lh L...
Our Answer: This remote can only control a millivolt gas valve. It only has the capability to turn such a valve on or off, either manually or thermostatically. We do offer some remotes that work with Signature Command Series controls that can control...
Our Answer: Indeed, this does sound like an issue with something in the fireplace behind or above the insert. As the unit heats the space around it, it brings out the odor in the surrounding area. I'd recommend having the unit pulled out and the inst...
Our Answer: This thimble is used when passing stovepipe through a combustible wall into a masonry chimney. The stovepipe will pass through the center of this thimble and terminate even with the inside of the masonry flue. It is not designed to provid...
Our Answer: This is a fixed, snap on hood that is compatible for use with many of the Empire manufactured fireboxes. In order to attach the hood, the metal delete plate must be removed from the top of the unit and the hood can be carefully snapped in...
Our Answer: This unit has a 42" wide by 24" tall viewing opening. It utilizes FMI's air cooled, double walled chimney system. While there is a larger 12" diameter chimney system made by FMI, the 8" system is sufficient to vent this fireplace, given i...
Our Answer: Unfortunately, no. These doors are specifically designed for use with Majestic's 36 Inch Al Fresco Outdoor Wood Burning Fireplaces and 36 Inch Sovereign Radiant Wood Burning Fireplaces. Your MBUC36 takes door kits HGD-36 or UGD-36A. Anoth...
Our Answer: This unit naturally pulls combustion air from the room in which it is installed. However, you do have the option to install a fresh air intake kit onto the unit. This will ensure a steady supply of combustion air. The fresh air adaptor is...
Our Answer: This unit simply requires the use of a flat head screwdriver or an adjustable wrench to tighten the set screws on the collar. The cap will need to be placed on the top of the chimney flue tile, then held level as you tighten the set screw...
Our Answer: This ceramic liner kit has 4 pieces--2 for the rear and 1 for each side. Please note they are only intended for use with Empire's 36" Tahoe Deluxe fireplaces. Here are the dimensions of the panels: Rear panel #1: 18 15/64" W x 13 17/64" H...
Our Answer: The LED lights are replaceable, but the big advantage of LED vs. incandescent is in life span. The operational life of LED lamps is 100,000 hours or 11 years of continuous operation. We do not offer any electric units with incandescent bu...
Our Answer: Replacement sand and embers should be all you need to make your log set look new again. However, our Platinum Bright Embers are a great addition to any gas log set. You may also consider adding lava rocks or granules to the floor of the f...
Our Answer: You are correct - our CPF-54110 is indeed designed to be mounted to the underside of a mantel to protect it from the rising heat of your fireplace. Is your tapestry hung directly above the fireplace, thereby above the mantel? If so, I thi...
Our Answer: This cap will likely not work for you. This style of cap is designed to press down inside factory built pipe with a 9" inside diameter. Of course, if there is access between the 2nd and 3rd wall of your chimney pipe, it may slide down int...
Our Answer: The B440-KT is not the correct blower for the HD81. However, the NZ64 is. You may find this blower here: Napoleon NZ64 Fireplace Circulating Blower Kit [1] From Page: NPL-B440-KT [2] Manufacturer's Product Number: B440-KT Our SKU: B...
Our Answer: I'm sorry but we do not offer installation of our products and are not affiliated with any installers in your area. You may try contacting a local plumber or contractor to assist you. Please let us know if you have any additional question...
Our Answer: I apologize that you are having trouble with your fireplace. We can most certainly order replacement parts for the unit. We do also offer wall mounted or hand held thermostats that can better control the unit. A few of those models do off...
Our Answer: This siding standoff will not match the DVVK4RP venting kit, however this part can be used: Dura-Vent DirectVent Pro Heat-Shielding Vinyl Siding Standoff - For Vent Pipes with a 4-Inch Inner Diameter [1] The DVVK4RP kit is comprised of Si...
Our Answer: While it is never recommended to reduce your venting diameter from the size of your flue collar, we do have a double-wall stovepipe reducer from 8" to 6". However, it is manufacturer specific, meaning you would have to have Selkirk DSP do...
Our Answer: Our Peterson log sets will burn with a bright yellow-orange flame, no matter the gas type. From Page: PTS-ESVG18-30-12P [1] Manufacturer's Product Number: ESVG18-30-12P Our SKU: ESVG18-30-12P Page ID: pts-esvg18-30-12p Links: --...
Our Answer: This brush features dimensions of 4 1/2" tall, 1 1/4" wide and 4 7/8" long. This brush has 1/4" thread holes, as well. From Page: UF-BRU-N5 [1] Manufacturer's Product Number: BRU-N5 Our SKU: BRU-N5 Page ID: fsd-bru-n5 Links: ---...
Our Answer: Per the manufacturer, a grate is not included with this stove. In fact, per page 5 of the owner's manual, you have the option to use either a layer of sand or firebrick approximately 1 1/2" thick. US Stove does make a grate specifically f...
Our Answer: Yes, you will want to find a local professional to install this insert and the 6" stainless steel liner that is required to vent it (not included). You may want to check out the National Fireplace Institute's website to find a local certi...
Our Answer: While the math is not exact, the closest thing to the oval is a 6 inch circle. A 6 inch circle is a couple of square inches smaller, but 7 and 8 inch liner is much bigger and would be too large for the application. From Page: CPF-69215 ...
Our Answer: This unit is indeed capable of operating with an outside air combustion kit. Installation of the kit is covered in section 2.6 of the downloadable owner's manual. The following items will be needed to complete the installation: Drolet Fre...
Our Answer: This is actually a crimp type reducer, as are all of the Snap-Lock products. Unfortunately, it is not available in stainless steel. Due to a low demand for stainless stovepipe, we do not currently carry any single wall pipe with a stainle...
Our Answer: I would highly recommend using at least one more set. These rocks are meant for use on a single 18" or 24" pan burner, so they would not fill out a fireplace of your size. From Page: PTS-STN-RIVERROCK [1] Manufacturer's Product Number...
Our Answer: This surround measures roughly 44" wide by 40" tall. It is designed for use with a particular model of manufactured fireplace and as a result, would need to be modified extensively to be used with a masonry fireplace. The surround has att...
Our Answer: We do not currently stock a mantel that can be adjusted to fit those exact measurements. We may be able to special order a mantel if the manufacturer is one that we deal with. Please advise who manufactured the unit and the model number. ...
Our Answer: You would need sufficient black stove pipe, including an elbow and stove adaptor, to run from the stove up to your wall exit point. You would also need a wall thimble, chimney tee with clean out, tee support and chimney components for out...
Our Answer: This item comes with the logs and the burner, as well as an automatic pilot kit for operation. You can add a remote control or wall switch to operate this set, these options are available in the drop-down menu below the pricing informatio...
Our Answer: You will need to install a shutoff valve to control flow of gas to this log lighter. While I cannot say there are any statewide restrictions on a product such as this, I would definitely advise to check with local code enforcement to ensu...
Our Answer: I was unable to locate an exact replacement door kit for your fireplace. In fact, my search lead me to believe that your fireplace is a Superior or Lennox fireplace. We do not offer doors for either of these brands. Please check out our u...
Our Answer: The listed 5 1/4" depicts the overall height of the grate. From Page: HYC-G22 [1] Manufacturer's Product Number: G22 Our SKU: G22 Page ID: hyc-g22 Links: ------ [1] http://www.efireplacestore.com/hyc-g22.html
Our Answer: We do. This unit requires 6" venting components. We have the necessary adaptors, stove pipe and chimney pipe that you'll need. If you'd like to reply with the details of your upcoming venting run, we'd be happy to build you a quote. You c...
Our Answer: This firebox does not come standard with any ceramic liner. The options for liner are listed in the "Accessories" tab on this page and you can choose any of those. These liners are not required, and if you purchase this firebox without ad...
Our Answer: In order to use the mantel that you have currently, the height of the opening would need to be altered somehow. The vent-free units that we carry to meet your width requirements are substantially taller than your mantel can house. Most ve...
Our Answer: A correction to my earlier email: According to the manufacturer, this unit will burn for approximately 11 hours with a fully filled fuel tray, and on the maximum setting of 10,000 BTUs/hour. From Page: NPL-WMFE3 [1] Manufacturer's Pro...
Our Answer: Unfortunately, we do not list a thermostat available for this unit at this time. Please call Empire at 866-214-9918 for further information on your model. From Page: CUI-RH50BLP [1] Manufacturer's Product Number: RH-50BLP Our SKU: ...
Our Answer: Per your criteria, yes, this tool set would be ideal for you. This is an affordable, quality alternative to some of our more expensive units. For example, please follow the below link. Pilgrim 5 Piece Burnished Bronze Iron Gate Fireplace ...
Our Answer: Napoleon's 1600 can effectively heat between 500 and 1500+ square feet. The 1100C has a slightly larger firebox and is suitable for spaces between 600 and 1600 square feet. The 1100C would be a fine choice for secondary heating at a more ...
Our Answer: While it is recommended to insulate chimney liners, it is not a requirement. Insulation will maintain the high flue temperatures needed for a strong draft. It will also provide appropriate clearance to combustibles. From Page: USS-2200...
Our Answer: We recommend a direct vent fireplace insert such as this Innsbrook model for a few reasons. Primarily, you would not need to concern yourself with the possible issues a vent-free insert brings (local building code enforcement restrictions...
Our Answer: This B-Vent fireplace or any of our Direct Vent fireplaces can be installed by a gas certified plumber or local contractor. From Page: CUI-VP325B1 [1] Manufacturer's Product Number: VP325B1 Our SKU: VP325B1 Page ID: cui-325b1 Li...
Our Answer: Unfortunately, we do not carry conversion kits for this type of appliance, as they use a different type of orifice and fuel injector than hearth appliances. I would recommend contacting the manufacturer directly for the proper part number...
Our Answer: This unit does not include venting components, however we do carry all the needed parts to vent the unit properly. From Page: MAJ-WDV500PTSC [1] Manufacturer's Product Number: WDV500PTSC Our SKU: WDV500PTSC Page ID: maj-wdv500ptsc...
Our Answer: This particular insert is designed to install into a masonry or factory built (metal) fireplace that is rated for a gas insert. As long as your fireplace meets this criteria and the wooden surround you are referring to meets minimum clear...
Our Answer: A regulator that can supply the gas valve with between 11 and 13 inches of water column must be used. Depending on the gas pressure that is being supplied from your tank, you may need to use a pair of regulators, as most household gas reg...
Our Answer: Per Peterson, the dimensions of the fireback are as follows: Center panel height - 16" Center panel width - 21.5" Side panel widths - 12" Side panel height - 14" The side panel and center panel heights are the same for all Peterson fireba...
Our Answer: An enclosure near the fireplace would have to be constructed if the unit is to be used under a covered patio. Past customers have had an enclosure built on the side of the home to conceal the tank and allow access to it. Burn time would b...
Our Answer: Listed shipping weight for this unit is approximately 300 lbs. From Page: CUI-WMC42 [1] Manufacturer's Product Number: WMC42 Our SKU: WMC42 Page ID: cui-wmc42 Links: ------ [1] http://www.efireplacestore.com/cui-wmc42.html
Our Answer: The back width of this grate is approximately 19". It is about 15" deep. Please note, as the page states, due to the nature of the manufacturing process, actual product dimensions may vary up to one inch. From Page: UF-C-1533 [1] Manu...
Our Answer: We can order these replacement parts directly from the manufacturer for your unit. The standard lead time for these parts is about 10 business days. From Page: FSD-B42L [1] Manufacturer's Product Number: B42L Our SKU: B42L Page ID...
Our Answer: No, this is not a universal fireplace hood. This is actually a hood extender, for use only on Empire's 42" Breckenridge Deluxe, Premium, and Select fireboxes. We do have some universal hoods, but the one we carry to fit over glass doors s...
Our Answer: Overall front width of this unit is 38". The manufacturer has designed these products with a 42" maximum allotment for televisions. Anything larger will likely not fit into the corner. From Page: FSD-18DM2105EMAH-SO [1] Manufacturer's...
Our Answer: This FMI specific blower measures 17 3/4" long by 5" tall by 2" deep. Each fan is about 3 3/4" wide. From Page: FSD-BK3 [1] Manufacturer's Product Number: BK3 Our SKU: BK3 Page ID: fsd-bk3 Links: ------ [1] http://www.efireplace...
Our Answer: This insert requires the use of a 6" liner or chimney system. From Page: NPL-EPI-1101P [1] Manufacturer's Product Number: EPI-1101P Our SKU: EPI-1101P Page ID: naepawobufii Links: ------ [1] http://www.efireplacestore.com/naepaw...
Our Answer: The louvers on this unit cannot be closed and you should always be circulating heat into the room. This process is aided by an electric blower that can be added to this model, if you don't already have one. The "L"-shaped handle you refer...
Our Answer: This cap should press right into your factory pipe with no problem. However, you'll want to confirm with your fireplace's installation manual that a cross-section of 50.3 square inches is an adequate vent opening. In Response to Questi...
Our Answer: Pilgrim does manufacture some of our better quality fireplace accessories. They are made of high quality materials here in the US and abroad. From Page: FSD-18006 [1] Manufacturer's Product Number: 18006 Our SKU: 18006 Page ID: f...
Our Answer: Per the manufacturer, a minimum of 24" needs to maintained above all flooring material. The unit also needs 6" on either side from any combustibles or surrounding enclosure. The unit must also have 18" above the mounting point for proper ...
Our Answer: This remote system will work with any non-solenoid type electronic spark ignition valve. I cannot say that I am familiar with this particular log set and I was not able to find any information on whether or not this is a solenoid equipped...
Our Answer: You may want to take a look at the following units. All of these use the same 4 x 7 twistlock piping system. The dimensions are all a bit narrower and a little taller than your previous model, but Majestic/Monessen have redesigned there u...
Our Answer: Typically, this issue occurs when the unit is not properly grounded. First, verify that the outlet the unit is plugged into is grounded properly. If you have a good ground at the outlet, there may be an issue with the ground to the chassi...
Our Answer: The variable flame pilot kit does have a standing pilot. The only pilot kit for vented logs that does not is the electronic pilot kit, but unfortunately this pilot does not provide the variable flame feature. Here is this log set with the...
Our Answer: While this model is too large to work, the smaller version of the unit would fit nicely: Small Innsbrook Vent-Free Gas Fireplace Insert with Built-In Thermostat [1] Any of the decorative surrounds could then be used to complete the unit. ...
Our Answer: This rack can be used with 2 x 4's of any length. It is completely customizable. From Page: HYC-SLRK [1] Manufacturer's Product Number: SLRK Our SKU: SLRK Page ID: hyc-slrk Links: ------ [1] http://www.efireplacestore.com/hyc-sl...
Our Answer: While we do not offer a duplicate setup like this in natural gas, we do carry several units that can be inserted into a white cabinet mantel and flanked by accessory bookcases, such as this item. One thing to consider however, is that the...
Our Answer: Given your description, it would seem that you only have an existing chimney with a clay thimble that the freestanding stove vents into. Unfortunately, we do not have a direct vent unit that can utilize this current setup. We do have line...
Our Answer: These should work fine for your application. However, being made of steel they do not offer as much flexibility as some of our other rods. So, depending on your insert and the presence of a secondary air tube or similar item, they may not...
Our Answer: The fireplace itself only requires the addition of an optional blower for completion. The venting system simply requires the needed length of chimney pipe (it is available in various lengths), a firestop support (if the chimney run is gre...
Our Answer: There should be no problem at all with installing this unit in this sort of application. As long as the chimney system is installed correctly with the proper rise above the roof, you should have no issues. Standard exit height is 3' above...
Our Answer: The item you've selected would work just fine for you. Or, if you'd like your grate to be a bit wider, you may be interested in our FSD-18610. Please follow the below link to view this item. Pilgrim Seven-Bar Narrow Steel Fireplace Grate ...
Our Answer: These bricks can indeed be used in the bottom of your fireplace. They should be mortared together with refractory cement. Please follow the below link to view an ideal cement. Rutland Pre-Mixed Refractory Fireplace Cement - 1/2 Gallon Tub...
Our Answer: Per the manufacturer, this product will not harm most types of asphalt or metal shingles. However, it is advisable to wash away any runoff onto the roofing material, as some older shingles can discolor if the product remains on them for t...
Our Answer: Being a vent free appliance, this unit is 99% efficiency. This is simply a function of the absence of a vent pipe in this unit. The logs and burner could be replaced if they developed a defect. However, they are singular to this insert. N...
Our Answer: While other models from the Classic Hearth series offer standard or optional blower systems, this model does not offer a blower. Due to the low output of this model, a blower would not be beneficial. I apologize for the confusion. The sta...
Our Answer: Yes, assuming proper clearances are met. The biggest thing to look for when determining how far above a gas unit you need to be before mounting a TV is the "mantel clearance" section of the owner's manual. Depending on the unit, this meas...
Our Answer: An insulated unit is recommended when installing on an exterior wall. The insulation prevents cold air from entering through the fireplace when it is not in use. The available glass doors for either unit can be found by clicking the Acces...
Our Answer: This unit is made of steel and features an Oil Rubbed Bronze finish. It's shipping weight is 47 pounds. It's dimensions are approximately 40" W x 25-1/4" H. From Page: UF-WAD792SP [1] Manufacturer's Product Number: WAD792SP Our SKU:...
Our Answer: The 3301 and 3301P do indeed utilize the same receiver assembly. However, the remote and receiver come as a matched set and a new receiver would be provided with the purchase of the 3301P. You can also use the 3301P manually and do not ha...
Our Answer: No, this item is just the firebox and does not include a burner or gas logs. Please see our gas logs page for some options: Gas Logs [1] This firebox will allow most of our 24" "see-thru" (2-sided) log sets if you want to use an automatic...
Our Answer: This lighter will have gas ports on one side only and the ports will be intended to face the front of the fireplace. The lighter is tapped and threaded to accept a gas line from either the left or right side of the fireplace and is provid...
Our Answer: Vent free fireplaces, even low BTU models like this one, are not suitable for a bathroom installation. It would be necessary to use a direct vent gas fireplace that has been rated for use in a bathroom. We have several models that meet th...
Our Answer: You may follow the below link to view the installation manual for Vermont Castings' current Encore stove. http://literature.mhsc.com/vermont_castings/manuals/30005295_Encore_2N1_7.pdf Page 19 appears to depict the installation instruction...
Our Answer: Yes, this blower will have a standard power cord that you will need an outlet to plug into for operation. From Page: FSD-BK [1] Manufacturer's Product Number: BK Our SKU: BK Page ID: fsd-bk Links: ------ [1] http://www.efireplace...
Our Answer: We are sorry, but that is not an item we are able to get separate from this fireplace. From Page: FSD-G50H [1] Manufacturer's Product Number: G50HA Our SKU: G50HA Page ID: fsd-g50h Links: ------ [1] http://www.efireplacestore.co...
Our Answer: The unit itself comes complete and ready to burn, however there is no pipe included and you will need to also purchase the CF11 double-wall class A chimney pipe. Please see the following link for the 48" length section of this pipe: Mones...
Our Answer: Indeed, there is. Please follow the below link to view our Real Fyre Crackler by R.H. Peterson. Real Fyre Crackler [1] From Page: SEI-FG9427 [2] Manufacturer's Product Number: 37-038-031-6-12 Our SKU: 37-038-031-6-12 Page ID: sei-...
Our Answer: We unfortunately do not offer a full enclosure screen like you are requesting. We currently only have the three-sided models. In Response to Question: I was wondering if you sell any woodstove guard screens that also have a top and a...
Our Answer: Absolutely, you may use the PTS-VR-1A remote as a replacement for your SR1001. From Page: PTS-VR-1a [1] Manufacturer's Product Number: VR-1a Our SKU: VR-1a Page ID: pts-vr1a Links: ------ [1] http://www.efireplacestore.com/pts-v...
Our Answer: The closest direct vent fireplace we have to your dimensions is the Medium Loft by Empire. You may view it by following the below link. Medium Loft Direct Vent Gas Fireplace with Remote-Ready Millivolt Controls [1] In Response to Questi...
Our Answer: Due to the heavy scaling on the gas starter pipe, I would recommend disconnecting the feed from the gas starter and replacing the whole assembly. Threading an older pipe will usually cause it to crack. It would be necessary to use a repla...
Our Answer: The primary concern with insulation being against the vent pipe is with the transfer of heat. The insulation, while noncombustible by nature, can heat up and transfer heat to adjacent framing members. This can cause the wood to dry out ov...
Our Answer: We have both wall mounted and hand-held thermostatic controls. The wall mounted unit can be found here: Vantage Hearth Wall Mounted Thermostat Kit - For Vantage Hearth Remote Ready Appliances [1] The hand-held version is here: Ambient RCS...
Our Answer: Lining a chimney will indeed work to ensure proper drafting of any appliance. Insulating a chimney liner for a gas furnace is not generally required unless climate constraints demand it. This, of course, is assuming that the manufacturer ...
Our Answer: This item is more designed for the removal of soot and creosote buildup. We really only list one item that fits your need. Unfortunately, we only offer it in one size. Please follow the below link to check it out. ChimneySaver Brick and M...
Our Answer: The best unit for your requirements will most likely be this model: Vantage Hearth LogMate VBV36 Value Series Smooth Vent-Free Gas Firebox - 36 Inch [1] It is just large enough to meet the minimum requirements and features a clean black s...
Our Answer: Unfortunately, we do not carry any universal faceplates, flashings or surrounds. All of our faceplates, such as this model for the Drolet Escape 1400 Woodburning Fireplace Insert [1], are model-specific. We apologize for this inconvenienc...
Our Answer: This fireplace does not require electricity to operate. It will continue to burn in the event of a power failure. However, if you are using an optional blower with this fireplace, it will only work during a power failure if you have also ...
Our Answer: Unfortunately, all of our current mantels offer heights around the 40" mark. However, some of our Pearl Mantels can be used with plinth blocks that raise their height. Please view one of our Pearl mantels here: Pearl Mantels Windsor Unfin...
Our Answer: The Viper GFK boasts a stand that allows the unit to stand on its own and does not need to be held to be used. This item would indeed be able to negotiate a 90 degree turn. A square brush is the ideal item to clean a square flue. A round ...
Our Answer: It is not recommended to use any adhesive when installing these panels. They should be cut to fit together inside your firebox and secured with clips that held the previous panels. If your firebox does not have clips, you may be able to f...
Our Answer: The proper plinths for the PRM-140 Classique mantel are the 604 plinths. These are not currently on our site but can be special ordered for you. Unfortunately, our free shipping policy does not include shipping to Alaska. In Response t...
Our Answer: This item is just a vent-free firebox, with no burner or ventless gas logs. You can indeed select a ventless gas log set that uses propane with its burner to use in this firebox, as long as the log set fits. Please see our ventless gas lo...
Our Answer: We may have a surround that can be retrofitted for use with your heater, but will need the complete height, width, and depth dimensions to be certain. Please provide this information and we would be happy to check. From Page: CUI-WSH24F...
Our Answer: If you have a vented log set, this stainless steel fireback will work well. It is 24" long, but features a three-sided folded heat shield design. If you have a ventless log set, it would not be recommended to use this or an other fireback...
Our Answer: Our ENC-LR1B has a total length of 25 inches. The kindling extension measures about 6". From Page: ENC-LR1b [1] Manufacturer's Product Number: LR1b Our SKU: LR1b Page ID: rerabyen Links: ------ [1] http://www.efireplacestore.com/...
Our Answer: That would all depend on the intended venting run and whether you are referring to maximum horizontal or vertical length. For example, with no vertical rise and venting right from the rear of the appliance, the longest allowable horizonta...
Our Answer: We do not currently offer either the transmitter or receiver for sale without the other. Please follow the below link to find an exact replacement for your current remote. Ambient RCT Programmable Thermostat On/Off Remote Control [1] In...
Our Answer: Unfortunately, it appears that neither of these Napoleon inserts would fit inside your fireplace. With your rear width and depth, they will not be able to be recessed far enough into your unit to fit properly. In Response to Question: ...
Our Answer: The 1450 actually does not have an ash pan as part of the stove. Please see this from page 29 of the owner's manual: "Since these models have no ash pan, shovel some ashes out through the door into a metal container with a tight fi tting ...
Our Answer: Per U.S. Stove, the built in thermostat can be adjusted down to 55 degrees. Due to the limitations of hydraulic thermostats, this is usually the lower limit. From Page: USS-DV21L [1] Manufacturer's Product Number: DV21L Our SKU: DV2...
Our Answer: According to the rated input of these units at full burn, it would consume approximately 6.24 gallons of fuel over a 24 hour period. From Page: CUI-DV25IN33LP [1] Manufacturer's Product Number: DV-25IN-33LLP Our SKU: DV-25IN-33LLP ...
Our Answer: These logs measure approximately 14" long and 3" across. From Page: PTS-SB-BONUS [1] Manufacturer's Product Number: SB-BONUS Our SKU: SB-BONUS Page ID: pts-sb-bonus Links: ------ [1] http://www.efireplacestore.com/pts-sb-bonus.ht...
Our Answer: Yes, we only have a few log styles available in a 36" see-thru (two-sided) setup. These include the Charred Royal English Oak, Golden Oak Designer Plus and the Split Oak Designer Plus. From Page: PTS-SDPG4-2-36-APK-17P [1] Manufactur...
Our Answer: Please note that this trim kit is simply an accessory for the R-Co Square Chimney Surround. You may find this surround by following the below link. Surround [1] To answer your question, this surround could work for you. You'd simply have ...
Our Answer: Technically, a 20 lb propane tank could fuel this heat, at the highest setting, for approximately 28 hours. However, due to the limited surface area available in a 20 lb tank and the evaporative nature of liquid propane, you will likely o...
Our Answer: This particular stove has a 19" clearance to each sidewall, using either single or double walled stovepipe. The unit requires 17.5" to a back wall with single wall stovepipe and 12.5" with double wall stovepipe. From Page: NPL-2100 [1] ...
Our Answer: I'm showing that your stove uses a SIT 820 control valve. These valves can only use remotes or thermostats made specifically for them. We do offer a few thermostatic remotes that are designed for use with a SIT 820 valve. Please follow th...
Our Answer: Per the manufacturer, this unit does not have an ICC Evaluation report. FMI currently has their products tested and listed by PFS Corporation and has done so for many years. This may be an acceptable alternative for local building codes. ...
Our Answer: If you need an electric fireplace to go within this mantel, we do have a variety of options that will fit within the 48" or 58" opening width, and you would need to fill in the remaining space. Please see these links for a couple of sugge...
Our Answer: There is no real way to reduce the heat output of this unit while maintaining large, attractive flames. However, it can indeed be controlled thermostatically. We have a few different options. Please follow the below links to view two of t...
Our Answer: It does not. All that is included is the fireplace, burner, and log set. This unit is 34 1/2" tall and 16" deep. The unit does not include a blower. It takes a BLOTMC. Please follow the below link to view this accessory. Monessen BLOTMC F...
Our Answer: Yes, this is incorrect, as this stove has a single door, as pictured. We apologize for the confusion. \ The Napoleon stove with double doors is the 1600C, please see it here: Napoleon 1600C Series Cast Iron Wood Burning Stove [1] From P...
Our Answer: It does indeed sound like you are encountering an issue with back draft that is causing the pilot to extinguish or a possible fluctuation in gas pressure that causes the pilot to go out on shutdown or start up. If the pilot goes out rando...
Our Answer: These fiber cinders are designed for use with Monessen DIS33 Vent-Free Fireplace Inserts and DFS Vent-Free Fireplaces. The cinders have a red glow when installed on the ember burner of a compatible Monessen fireplace. From Page: CUI-CI...
Our Answer: Due to the large wood mantel and the limited BTU output of the gel canisters, there would be no issue with installing a TV above this fireplace. From Page: FSD-7100A-O [1] Manufacturer's Product Number: 7100A-O Our SKU: 7100A-O P...
Our Answer: Direct vent appliances feature two vent pipes and a sealed combustion chamber. They pull combustion air from outside the home and vent their exhaust right back outside, as well. Of course, vent free units are different in that they use av...
Our Answer: While this plate is designed for 42' dampers, it actually measures 7" D x 34 1/2" W. This damper plate, our largest, will unfortunately not be large enough for your application. From Page: CPF-26265 [1] Manufacturer's Product Number:...
Our Answer: Unfortunately, the manufacturers of the remotes we carry will not sell just the transmitter. A transmitter will only be sent out to replace a defective unit that you already have in your possession. Otherwise, a complete transmitter and r...
Our Answer: This item is simply a small trim piece designed to fit onto the bottom of Empire's SC256BL Cast Iron surround Kit. You may view the SC256BL by following the below link. Empire SC256BL [1] This C256BL trim piece only measures about 1 5/16"...
Our Answer: This cap is indeed designed to protect your B-Vent appliance during bouts of high wind. However, it is only designed for use with Simpson Dura-Vent chimney systems. It features twist-lock tabs that are specific to this line of chimney pip...
Our Answer: There is a small button located on the face of the receiver that must be pressed and held using a pen or toothpick. The receiver should emit an audible tone at this point. Once the tone is heard, you may push any button on the remote unti...
Our Answer: Yes, you may add glass doors to this unit. Please see the following link for a set of black doors: Vantage Hearth Black Bi-Fold Glass Door with BlackTrim for See-Thru Woodburning Fireplaces [1] Here are your other options: Brushed Brass D...
Our Answer: Yes, all of our direct vent gas inserts that use propane will have a fixed glass panel that cannot be opened during operation. This insert is vent-free and, like all vent-free units, will not have a fixed glass panel as it must be open to...
Our Answer: The blower in this unit is indeed a squirrel cage fan, and the glass is ceramic on this insert. Our gas fireplace inserts use a millivolt pilot, which is not the same as an automatic starter or electronic ignition. The millivolt pilot sys...
Our Answer: Empire says the bottom width of this 60" mantel shelf is 53 3/8". From Page: CUI-MS60UH [1] Manufacturer's Product Number: MS-60-UH Our SKU: MS-60-UH Page ID: cui-ms60uh Links: ------ [1] http://www.efireplacestore.com/cui-ms60u...
Our Answer: A poker style can be swapped out for a rotary style. You will indeed need to drill a hole through the face of your fireplace to install the rotary style. No sealant will be required. From Page: CPF-26290 [1] Manufacturer's Product Nu...
Our Answer: Per Vestal, the nominal thickness of the cast damper plates is 1/4". Slight differences in the manufacturing of the plate can result in slightly thinner or thicker spots. From Page: CPF-26255 [1] Manufacturer's Product Number: 97-011 ...
Our Answer: This wood burning insert can only be utilized in a masonry or manufactured fireplace that is listed to accept an insert. If you plan on removing any existing appliance, you would need to replace it with another manufactured fireplace or a...
Our Answer: Most certainly. Manufactured fireplaces, such as this model, are designed for the versatility and can be installed in homes new and existing. You will simply need to pick a spot that will have the space to accommodate the unit and the ass...
Our Answer: This gasket is not hollow braided, and it is graphite-impregnated for enhanced durability and abrasion-resistance. From Page: RUT-723W [1] Manufacturer's Product Number: 723W Our SKU: 723W Page ID: rut-723w Links: ------ [1] htt...
Our Answer: Obviously, the liners on this page will not work for your unit because they are fiber liners meant for use in gas fireplaces. We do not have model-specific wood burning refractory panels, but we do have some universal ones you could use. ...
Our Answer: Unfortunately, not. We currently only offer these kits and not their component parts. From Page: USS-BKAD500 [1] Manufacturer's Product Number: BKAD500 Our SKU: BKAD500 Page ID: uss-bkad500 Links: ------ [1] http://www.efireplac...
Our Answer: Yes, the unit can generate up to 55,000 BTUs and heat up to 1,500 square feet. From Page: NPL-1100C [1] Manufacturer's Product Number: 1100CP-1 Our SKU: 1100CP-1 Page ID: npl-1100c Links: ------ [1] http://www.efireplacestore.co...
Our Answer: Every model of fire back that we currently carry has been designed for installation into a traditional, open faced fireplace. The temperatures achieved by a closed combustion wood stove would damage a fire back, even a stainless model suc...
Our Answer: At the least, you will also require several sections of FMI Class A chimney, a ceiling firestop, and a termination cap. I will be happy to get a list of needed items together for you. Will the unit be installed on an interior wall or buil...
Our Answer: Unfortunately, the manufacturer has recently discontinued the 17" straight LP log lighter (labeled "E" in the picture) and it is no longer available. We apologize for this inconvenience. From Page: CPF-47120 [1] Manufacturer's Produc...
Our Answer: This unit does indeed come complete with everything needed for installation. You will simply need to have a gas line in place and frame the unit into a wooden wall cavity or cabinet. We also offer the decorative wooden cabinet that the un...
Our Answer: Peterson's WS-3 includes about 15' of wiring, 4 AA batteries, a white switch cover and black plastic toggle switch to vary the flame height of your Peterson burner assembly. In Response to Question: I have a Peterson Real-Fyre Vented...
Our Answer: If you are unsure of the installation of this gas insert, I would recommend consulting with a reputable local contractor or HVAC technician. Usually, either of these options will be good resources to install a unit such as this. From P...
Our Answer: Unfortunately, no. While this mantel is made of solid pine, it is not treated to withstand the elements. It is designed to be used indoors only. From Page: PRM-412 [1] Manufacturer's Product Number: 412-24 Our SKU: 412-24 Page ID...
Our Answer: While we do carry several large wood burning inserts that have a small ledge, these differ in their installation from the NZ6000. The NZ6000 is a built-in fireplace, which requires wooden framing prior to installation. The inserts are des...
Our Answer: This mesh curtain is made of heavy duty 19.5 gauge steel. This gauge and the small 3/16" diameter of the mesh will help prevent this screen from suffering the same fate as your existing screen. From Page: FSD-RMP2426 [1] Manufacturer...
Our Answer: The primer is a translucent white color and will need to be painted, as it does not completely cover the wood grain on it's own. Detailed installation instructions are included with the mantel on delivery. You can definitely cut the breas...
Our Answer: The basic 810 models are capable of moving 105 CFM of air, while the larger 812 model can move 150 CFM. The operating temperature between the two is very similar. Besides differences in blade color, these are the only things that separate...
Our Answer: You have a variety of options for a replacement gas fireplace. We recommend reading our Gas Fireplace and Stove Buying Guide [1] for more information. As for the pipe, you will need to vent the gas unit separate from your existing triple-...
Our Answer: That would depend on the make and model of your fireplace. These particular panels are designed to be used exclusively with Vantage Hearth's LogMate Fireplace. If you'd like to reply with the model number of your fireplace, we'll be happy...
Our Answer: Unfortunately, the BR36 is a manufactured unit that is not rated for use with a wood burning fireplace insert. The 1101 also cannot be used without being installed into an approved manufactured or masonry fireplace. It would be necessary ...
Our Answer: This door is designed to be used specifically with FMI's Mission fireplaces. As it is an FMI proprietary product, they will not provide the specifics as far as measurements are concerned. A universal fit door would probably be the best op...
Our Answer: This is most easily done by measuring across your flue opening. A flue that is 6" in diameter requires a 6" brush. From Page: RUT-16906 [1] Manufacturer's Product Number: 16906 Our SKU: 16906 Page ID: rut-16906 Links: ------ [1]...
Our Answer: This concern could be caused by a few different things. These range from clogged burner ports to blocked venturis in the burner tubes. There is also an excessive flow safety device that could have potentially been tripped. Please download...
Our Answer: This item can be viewed in a much larger format by opening the product brochure. This is listed as a PDF at the bottom of the item features page, titled "download product manual #2". This brochure will contain a large image of the unit on...
Our Answer: As this paint is designed to withstand high-temp applications, it would indeed be suitable for stove pipe. From Page: CPF-43255 [1] Manufacturer's Product Number: 6283 Our SKU: 6283 Page ID: cpf-43255 Links: ------ [1] http://ww...
Our Answer: A 45 degree elbow could not be utilized directly off the back of the stove, however it could be attached directly onto the back of the pipe adapter that is provided with the kit. You can then utilize straight pipe to pass through the wall...
Our Answer: This mantel is only available with a primed finish or as an unfinished unit. You may find the unfinished version by clicking the Accessories tab on this item page. From Page: CUI-MFL48PG [1] Manufacturer's Product Number: MFL-48-PG ...
Our Answer: The stove you mention is a tad bit large for your application. Our general rule of thumb is 35 BTU per square foot. Per your description, the USS-2000 would be a great option for you and it includes a blower. Please follow the below link ...
Our Answer: Indeed, this unit will work well for your application. From Page: CPF-47117 [1] Manufacturer's Product Number: 47117 Our SKU: 47117 Page ID: cpf-47117 Links: ------ [1] http://www.efireplacestore.com/cpf-47117.html
Our Answer: Either of the following door assemblies would be compatible with the unit you have. FMI Extruded Aluminum Bi-Fold Glass Doors for 42 Inch Mission Gas Fireplace - Black [1] FMI Extruded Aluminum Bi-Fold Glass Doors for 42 Inch Mission Gas ...
Our Answer: This unit can accept logs with a maximum length of 21 inches. A total of 4 logs, ranging from 3 to 4 inches in diameter will be the maximum capacity for this stove to burn efficiently. It is not recommended to stack the logs in the unit. ...
Our Answer: This adaptor features an oval measurement of 7" x 6". From Page: CPF-73675 [1] Manufacturer's Product Number: BM0039 Our SKU: BM0039 Page ID: cpf-73675 Links: ------ [1] http://www.efireplacestore.com/cpf-73675.html
Our Answer: This Classic Flame insert is manufactured by Twin-Star International, which has dedicated manufacturing facilities in southern China. From Page: FSD-36EB110-GRT [1] Manufacturer's Product Number: 36EB110-GRT Our SKU: 36EB110-GRT ...
Our Answer: The 4" refers to the horizontal base of the triangle, the bottom of the hood, measuring the protrusion of the hood from the wall. From Page: FSD-EUCH4L [1] Manufacturer's Product Number: EUCH4L Our SKU: EUCH4L Page ID: fsd-euch4l...
Our Answer: Unfortunately, no. We only carry the Empire floor furnaces. These require floor openings of 32 5/16" x 20 5/16" (model 3588), 34 5/16" x 22 5/16" (model 5088), and 34 5/16" x 30 5/16" (model 7088). From Page: CUI-3588NAT [1] Manufact...
Our Answer: This blower is an electric accessory model that must be plugged into a 110 volt outlet to operate and works off of a thermostatic control. It is possible to use a product, such as an ecofan, to circulate heat. The particular model that is...
Our Answer: The particular stove has a depth of 12 7/8" from the lintel to the very back of the firebox. However, since it is a 45 degree venting stove, it will be necessary to allow for 14" of total space to properly install a flue collar. In Resp...
Our Answer: This particular stove is rated to heat a maximum of 2,000 square feet under high burn. Location of the stove within your home, insulation of the home, and height of your ceilings will all have effects on it's effectiveness. From Page: N...
Our Answer: This fireplace requires the FMI Air-Cooled chimney pipe, 8" inner diameter. We sell this pipe and all the appropriate components (firestops, flashing, storm collar, cap). Please see this link for the 48" length of the pipe: FMI Wood Firep...
Our Answer: The dimensions for this unit are located in the item features section and are as follows: 41" H x 39 1/2" W x 14 5/8" D These measurements are for the far most points on the cabinet itself. From Page: CUI-VFD26FM30NN [1] Manufacturer'...
Our Answer: Generally speaking, you need about 35,000 BTUs to heat 1,000 square feet. However, with your poor insulation, you may want to look in the 40,000 BTU range for adequate heating. From Page: CUI-3588NAT [1] Manufacturer's Product Number...
Our Answer: While this SPK-26 is an manual gas valve with standing pilot, it does not include an O.D.S. system and is intended primarily for use with vented gas logs. For your application, I highly recommend contracting a gas plumber to evaluate the ...
Our Answer: Unfortunately, there is not a way to do this currently. Bio Flame will most likely release a version of this unit with a fuel tray, rather than the cans. The company rarely releases both versions at once and this model is fairly new. Fr...
Our Answer: Unfortunately, Pearl Mantels, the manufacturer of this mantel shelf, does not offer legs to go with this style at this time. From Page: PRM-495 [1] Manufacturer's Product Number: 495-48 Our SKU: 495-48 Page ID: prm-495 Links: --...
Our Answer: In selling plenty of both of these inserts, we have not noticed any difference in the dependability or durability of these doors. Both are solid units and reliably manufactured. The choice you make should be based on how you want your ins...
Our Answer: These doors being designed specifically for FMI's Bungalow fireplace have approximate dimensions of 36" x 21.5". They attach via locating pins that mount into holes on the Bungalow's front. From Page: FSD-BDB36B [1] Manufacturer's Pro...
Our Answer: Per the manufacturer, this blower measures approximately 4" deep, 4" tall, and 11" long. Please keep in mind that this blower assembly is meant for installation in certain Empire fireplaces. While it may physically fit into other brands, ...
Our Answer: BTU output is subject to the type of wood that is burned and Napoleon rates this unit from an 11,500 BTU minimum, using softwoods with high moisture content, to a 70,000 BTU maximum using hardwoods with low moisture. From Page: NPL-NZ-2...
Our Answer: That is correct. Black iron pipe with a 1/2" diameter is the most commonly used material to make this connection. From Page: CPF-47120 [1] Manufacturer's Product Number: 47120 Our SKU: 47120 Page ID: cpf-47120 Links: ------ [1] h...
Our Answer: We do not have that information available. We would encourage you to contact FMI at 1-866-328-4537 and see if that is something with which they may assist you. From Page: FSD-BD36B [1] Manufacturer's Product Number: BD36B Our SKU: ...
Our Answer: Unfortunately, the manufacturer does not provide dimensions of the individual panels for this kit. Each kit is designed to be used with a certain model of fireplace, in order to ensure that there will not be any problems with the operatio...
Our Answer: To keep the unit from cracking, it is best to burn at least 2-3 small fires for 1 hour at a time. The fires should be kept to only kindling and 1-2 small logs that will burn down within the 1 hour time frame. This allows any remaining moi...
Our Answer: Absolutely. You would simply need a circular saw with a masonry blade to cut these panels to the appropriate size. From Page: CPF-42428 [1] Manufacturer's Product Number: 42428 Our SKU: 42428 Page ID: cpf-42428 Links: ------ [1]...
Our Answer: It sounds like you may have looked at the fan numerous times or evaluated other models and they were added to your shopping cart. You should be able to view all items in your cart and see all items added. To remove any unwanted fans, eras...
Our Answer: These embers are intended to be added to the ember bed of a vented gas log set. They glow when heated. So, for ultimate effect, place them evenly where they will be contacted by the flames of the burner. From Page: ACS-PBE [1] Manufa...
Our Answer: I am not familiar with this model of Desa fireplace. However, their V36 is a line vent-free units that, due to their vent-free nature, do not have available door kits. From Page: FSD-BD36 [1] Manufacturer's Product Number: BD36 Our...
Our Answer: Certainly. It is acceptable to have a short run of horizontal pipe before returning to a vertical run. Keep in mind however, that it is best to have at least 12" of vertical run before turning horizontal. This is necessary to establish a ...
Our Answer: The blower should indeed drop down beneath the floor of the fireplace, behind the control valve. Will the fan not fit into the floor of the fireplace or does it simply sit too tall to allow for the reinstallation of the burner assembly? ...
Our Answer: No, this price is for one 24" x 28" panel. We offer these panels in one 24" x 28" panel on this page and also in a set of two 24" x 40" panels, which you can find here: Hargrove Replacement Fireplace Refractory Panels - 24 inch X 40 inch ...
Our Answer: Neither the ash drawer nor blower are included with this stove. However, both can be added. The blower can be found on the Accessories page and the Ash Drawer is the last option to be added before adding this item to your cart. This unit ...
Our Answer: This stove must be at least 10" out from the back wall, as illustrated in the owner's manual on page 9. The product manual is available to be downloaded on this product page. Napoleon does not list a minimum requirement for the pipe, but ...
Our Answer: As long as the damper throats are in good condition, you should be able to replace just the plates without much difficulty. We also carry the replacement rotary controls for the damper assemblies. The rotary control can be seen here: Vest...
Our Answer: The logs that come with this unit cannot be substituted for any other log set. We apologize for this inconvenience. From Page: FSD-ALTC-C [1] Manufacturer's Product Number: ALTC-C Our SKU: ALTC-C Page ID: fsd-altc-c Links: -----...
Our Answer: I am not aware of the 1802 clayton ever being manufactured with a 6" flue collar. We have carried the US Stove line for some time now and the 1602 clayton has always been the version that came with a 6" collar. Early 1602's were painted g...
Our Answer: Per Empire, the correct part number for the thermocouple you need is R1195. This part is available to be ordered directly from Empire. We will be happy to place the order for you. From Page: CUI-RH25NAT [1] Manufacturer's Product Numb...
Our Answer: If your fireplace is listed to accept an insert, then you can use this unit. You would not be able to utilize your woodburner's blower or the glass doors, as any vent-free appliance has to operate while open. From Page: CUI-DIS33NVG [1...
Our Answer: Yes, this is an add-on, and you can find the Bay Door under the accessories tab on this page. From Page: NPL-GI3600 [1] Manufacturer's Product Number: GI3600-4N Our SKU: GI3600-4N Page ID: npl-gi3600 Links: ------ [1] http://www...
Our Answer: These doors are designed to be used specifically with FMI's Mission B-Vent Gas Fireplace. From Page: FSD-BD36B [1] Manufacturer's Product Number: BD36B Our SKU: BD36B Page ID: fsd-bd36b Links: ------ [1] http://www.efireplacesto...
Our Answer: While unvented heaters may produce some odor it is not normal for the odor to be over powering or overly noticeable. However, a "burn in" is necessary to burn off the oils and lubricants used during assembly. It is recommended to open a f...
Our Answer: Sliding mesh screens do not come standard with this door assembly, however they can be specified and added. Because this door assembly is made to order, it is not returnable unless damaged or defective. From Page: FSD-9100-3621-09 [1] ...
Our Answer: The "+6" indicates the additional amount in dollars for the additional length of pipe that you are selecting. From Page: CPF-69055 [1] Manufacturer's Product Number: 1812 Our SKU: 1812 Page ID: cpf-69055 Links: ------ [1] http://...
Our Answer: This unit is indeed shown with optional brass trimmed doors in place. The unit will come with an open face and a smooth black metal surround. Unfortunately, FMI does not currently have a photo of this unit available without the doors inst...
Our Answer: The entire assembly on this patio heater is indeed constructed of stainless steel, however many of these models can rust prematurely after 1-2 years. The manufacturer does warranty against rust in most circumstances, however the warranty ...
Our Answer: Unfortunately, the manufacturer does not have any chimney extensions available for this unit. From Page: MRS-BBQTAN [1] Manufacturer's Product Number: BBQTAN Our SKU: BBQTAN Page ID: oufiwibbqtan Links: ------ [1] http://www.efi...
Our Answer: Unfortunately, FMI currently only offers this unit in the herringbone style that is shown. From Page: FSD-F48HR [1] Manufacturer's Product Number: F48HRA Our SKU: F48HRA Page ID: fsd-f48hr Links: ------ [1] http://www.efireplace...
Our Answer: This mantel features hardwood construction and can indeed be trimmed down. From Page: CUI-MFL52PG [1] Manufacturer's Product Number: MFL-52-PG Our SKU: MFL-52-PG Page ID: cui-mfl52pg Links: ------ [1] http://www.efireplacestore....
Our Answer: This unit features a center height of 31". The center panel's lowest height and the side panels' tallest point are a common 28 3/4". The lowest point on the side panels is right at 28". From Page: CPF-61029 [1] Manufacturer's Product...
Our Answer: The opening dimensions for this surround are approximately 34" W x 24 3/4" H. The outer dimensions are 46" W x 30 5/8" H. Please note that this surround is meant for use only with the Empire Large Innsbrook Fireplace Insert. From Page:...
Our Answer: This item includes a 19 Inch gas coal basket with manual safety pilot, a decorative black cast iron gas basket featuring coal motifs, 9 ceramic coals and a 20,000 BTU burner. From Page: FSD-OBCO19N1B [1] Manufacturer's Product Number...
Our Answer: Unfortunately, this door assembly will not work in place of the DG36E doors, however I do believe these doors are still available from the manufacturer. However, please be aware that this part number denotes a brushed brass finish, not a ...
Our Answer: If your application will meet clearances stated in the manual, then yes, you may install this unit there. Please see the owner's manual for the stated minimum clearances for this unit. The owner's manual can be downloaded on this product'...
Our Answer: The assembled weight of this fireplace is 45 pounds. Gel fuel fireplaces are indeed a simple, effective solution for heating small areas and do not give off the byproducts of a gas fireplace. From Page: SEI-FA5847 [1] Manufacturer's P...
Our Answer: This fireback comes with legs with several slots, allowing you to adjust the angle of the fireback. The slotted support legs provide possible 65
Our Answer: The manufacturer of this paint specifically advises against using it on cooking surfaces. Unfortunately, none of the paint we offer is recommended for use on such surfaces. From Page: CPF-42100 [1] Manufacturer's Product Number: 4210...
Our Answer: While this unit does not come standard with glass doors, they are available in several different finishes, per your needs. The doors can be seen the accessory tab on the item page. Each side of the unit will require a separate set of door...
Our Answer: This piece has an oval end of 7" x 6". We recommend visiting a machine shop or a sheet metal fabricator to get a piece for your requirements. From Page: CPF-73675 [1] Manufacturer's Product Number: BM0039 Our SKU: BM0039 Page ID:...
Our Answer: Unfortunately, this is a bit of an odd sized adapter that we do not currently carry. On many older models of stoves, the manufacturer made individual adapters that had to be used with that particular stove. In most cases, it will be neces...
Our Answer: Unfortunately, we do not currently offer any woodburning peninsula fireplaces that have an option to add a blower. The only multi-sided units that can add a blower are gas fireplaces. From Page: CUI-VPN36-A [1] Manufacturer's Product...
Our Answer: Simpson Duravent has actually just released a direct vent chimney system for wood stoves, know as DuraPro. However, we do not carry any stoves that are compatible with the system, as it requires the stove to have a separate 3" intake air ...
Our Answer: The key to good operation with a see-thru wood burning unit, is the chimney installation. Because of the fact that the fireplace is open on both sides, there is more of an opportunity for the unit to backpuff if the chimney is too short o...
Our Answer: Each side, along with the top of this surround, measures 6 inches. The surround is made specifically for the DV25IN33LN or DV25IN33LP fireplace, which has a width of 27.5 inches and a height of 18 3/8". We cannot guarantee that this surro...
Our Answer: The approximate dimensions listed in the "Features" section are indeed for the unit itself. The framing dimensions for this unit, as specified in the manual, are 34 3/8" W, 35 3/4" H, and 16 3/8" D. Please see page 14 of the owner's manua...
Our Answer: The NPI 45 offers a bit more in terms of BTU capability and burn time. It also offers more options, like the Four-stage FAILSAFE system features an automatic blower override, a high temperature limit switch, a low air pressure switch, and...
Our Answer: The millivolt pilot system has a small flame that generates power for the unit's gas valve to operate, and yes, you will have a standing pilot. As a result, they do not require outside power to operate and can be used in the event of a po...
Our Answer: I believe you may be referring to the DVD36FP30N-2, rather than DBD. If so, the FBB4 is indeed the correct blower assembly. While it is easier to install the blower before the unit is fully plumbed, it is certainly possible to install the...
Our Answer: Of course, not knowing the details regarding your fireplace, we would be unable to provide a definite recommendation. However, this unit produces safe heat without any fumes or pollutants. It requires no vent and works off of a standard w...
Our Answer: This unit features a built-in safety screen curtain but no glass front. From Page: CUI-VFP28IN23L [1] Manufacturer's Product Number: VFP-28IN-23LN Our SKU: VFP-28IN-23LN Page ID: cui-vfp28in23l Links: ------ [1] http://www.efire...
Our Answer: To complete your installation, you will need enough single or double wall stovepipe to span the distance from the top of the stove to the roof decking, then a support box will install into the decking and act as the conversion point to a ...
Our Answer: This hood will install rather easily into an Empire Breckenridge fireplace. It simply attaches via screws into the fireplace opening. From Page: CUI-VB4H42BL [1] Manufacturer's Product Number: VB4H-42-BL Our SKU: VB4H-42-BL Page ...
Our Answer: I'm sorry, but none of the woodburning fireplaces we sell would be able to house your stove. You may want to look into Martin Industries, as they have manufactured units to house stoves such as yours. From Page: FSD-B42 [1] Manufactu...
Our Answer: This insert is meant for installation in existing masonry fireplaces or certain manufactured units listed to accept an insert. We encourage you to check with the manufacturer of your Heatilator unit to see if it is listed to accept an ins...
Our Answer: The two options you have for a blower for this fireplace (GZ550 or B440) can both be installed at a later date, if you so choose. Please see the owner's manual on this page for installation instructions. The letters "BGD" and "GD" stand f...
Our Answer: This ceramic liner kit has 3 pieces--1 for the back and 1 for each side. Please note that they are only intended for use with Empire's 36" Breckenridge Deluxe fireboxes. Here are the dimensions: Rear panel: 29" W x 19" H Side panels: 15.5...
Our Answer: This grate measures approximately 27" Wide x 6" High x 15 1/4" Deep. From Page: UF-C-1534 [1] Manufacturer's Product Number: C-1534 Our SKU: C-1534 Page ID: fsd-c-1534 Links: ------ [1] http://www.efireplacestore.com/fsd-c-1534.h...
Our Answer: All you need to do to have this fireplace as you describe is to select the L36K "Painted Black Louvres" from the drop-down menu after you select your fuel (Natural Gas or Propane). This fireplace, like any direct vent unit, comes with a g...
Our Answer: Yes, this unfinished hardwood is indeed stain grade. Empire also makes primed mantel shelves which are the paint grade, which we also have available. From Page: CUI-MS72UH [1] Manufacturer's Product Number: MS-72-UH Our SKU: MS-72-...
Our Answer: This shield can certainly be trimmed to fit your application. I would however, recommend the use of a stationary band saw over a jig saw, as this would give better results. You could then place the cut end against the mantel to make it le...
Our Answer: Are you using this product currently or a different version? Is your furnace constantly cycling on and off every few minutes? These units operate via a 3 degree swing. In Response to Question: My burners keep coming on for 1 to 2 mini...
Our Answer: This would indeed be an appropriate unit to be placed on an interior wall between rooms. The wall would of course need to be built out to accommodate the depth of the fireplace. However, there is a strict code that limits BTU output in a ...
Our Answer: No, any ventless gas log set needs to operate with doors open to allow for combustion air and proper exhausting. From Page: PTS-RD9G9-20-ManualN [1] Manufacturer's Product Number: RD9G9-20-ManualN Our SKU: RD9G9-20-ManualN Page I...
Our Answer: This blower does indeed work off of a 110V power outlet and comes with a standard electrical cord that would be plugged into the outlet. This blower is made for specific models of Napoleon fireplaces and can help to circulate heat on a lo...
Our Answer: This valve can be installed in your firebox and includes an adaptor and 90 degree pipe elbow to aid in installation. It will connect directly to a 1/2" standard gas line. The overall length of the handle is 7". From Page: PTS-AV-18 [1] ...
Our Answer: If the existing fireplace is manufactured by FMI or Vantage Hearth and the existing chimney pipe is the same diameter and in good condition, it may be reused. Each manufacturer typically utilizes a different diameter or style of vent pipe...
Our Answer: While we do not have a premade kit to vent through a wall, we do have all the necessary Class A chimney components to do so. If you would like to provide dimensions for your proposed chimney system, we will be happy to get a quote togethe...
Our Answer: Unfortunately, we do not have samples available for this item. We strive to maintain the lowest prices available at all times, but the sale price depends on availability from the manufacturer and demand from the customer. From Page: MRS...
Our Answer: This item is simply a firebox. It does not include a gas log set or burner assembly. You may view our gas log set options by following the below link. Ventless Gas Logs [1] From Page: CUI-VFD42FB0L [2] Manufacturer's Product Number: V...
Our Answer: We can usually special order individual parts for blower kits, but Monessen is the exception to this rule. They currently will not sell parts of the kits by themselves, due to the complexity of the items. From Page: CUI-BLOTSC [1] Man...
Our Answer: This component is actually meant to begin a stovepipe installation from the top of the stove itself and would not work for your needs. It will be necessary to reverse the direction of your venting system, crimp the end of one pipe to slid...
Our Answer: Yes, if the log set is not installed, the grill feature can readily be used. From Page: MRS-BBQTAN [1] Manufacturer's Product Number: BBQTAN Our SKU: BBQTAN Page ID: oufiwibbqtan Links: ------ [1] http://www.efireplacestore.com/...
Our Answer: This unit will indeed include all three glass panels to fully enclose the appliance. The burner assembly is also built-in. The log set and venting assembly will need to be added to complete installation. From Page: CUI-DVP36PP32EN [1] ...
Our Answer: This insert can indeed receive finishing material to compensate for a fireplace opening that is larger than its exterior dimensions. From Page: FSD-36EB110-GRT [1] Manufacturer's Product Number: 36EB110-GRT Our SKU: 36EB110-GRT P...
Our Answer: Unfortunately, this triple-wall pipe will not fit your pipe's dimensions. This pipe has an 8" inner diameter, with 11" and 13 1/8" outer diameters. In Response to Question: I have to extend two majestic triple wall chimney pipes for ...
Our Answer: Currently, Napoleon only offers a Convex Stainless Steel surround for this fireplace. This option can be found in the drop down menu on the item page. From Page: NPL-WHVF31N [1] Manufacturer's Product Number: WHVF31N + S31RK Our SK...
Our Answer: These universal door assemblies are indeed designed to be installed onto the front of your fireplace. In Response to Question: Does the outer frame fit in front of the fireplace, overlapping the sides, top and bottom? Or is it suppos...
Our Answer: While it is recommended that any flexible portion of Dura-liner be insulated, it is not always necessary. In your case, if the flexible section is located in an area below the flue tiles you have been removing, it would not be needed. How...
Our Answer: The angled lip on this shield is meant to protrude out and up along the front of the mantel. It would be difficult to shorten the lip, given the radius that has been applied to it. If the shield needs to be shortened, your only option wou...
Our Answer: Cast iron grates are generally not as durable as diamond or stainless steel grates. The metal is inherently more brittle and can crack after a short time of use under high temperatures. The grade of iron can also make a difference. Many c...
Our Answer: Unfortunately, replacement ceramic liners are sold by brand, rather than dimensions. We carry many ceramic liners, but do not stock an exact liner for Peerless fireplaces. It would be necessary to purchase a direct fit liner for that exac...
Our Answer: Clearances from the deck will depend solely on the type of fire pit or burner you are using. Please advise as to which product you currently have installed. I will be happy to check the clearances for you. From Page: FSD-12202 [1] Man...
Our Answer: Most universal keys are only 3" long and cannot be used in a recessed application. This version is 12" and may be suitable for your needs. You will need to use an object, such as a pen or pencil, to gauge the depth of the shutoff. You wil...
Our Answer: This light switch is specifically designed to control a gas log set that utilizes a millivolt pilot control. This pilot system has a small flame that generates power for the unit's gas valve to operate. As a result, they do not require ou...
Our Answer: 1. The width measurement of this door's glass panel is 15 1/2". The top is slightly arched with the highest point in the center. The center height measurement is 9 3/4". 2. No, liner is not included in this package deal. This is because, ...
Our Answer: It is manufactured out of 24 gauge steel and is a direct fit hood for the Breckenridge line of fireboxes that Empire manufactures. This is an extended model of hood that is designed to replace the standard model, should extra mantel prote...
Our Answer: As long as there is not a danger of the grate contacting an part of the heating element in the stove itself, there will be no reason that this paint could not be used for this type of application. From Page: RUT-81 [1] Manufacturer's ...
Our Answer: These panels are light gray in color. From Page: CPF-42428 [1] Manufacturer's Product Number: 42428 Our SKU: 42428 Page ID: cpf-42428 Links: ------ [1] http://www.efireplacestore.com/cpf-42428.html
Our Answer: Indeed, they cannot. It is recommended to use only the embers included with or made specifically for your vent free log set and nothing more. From Page: RUT-585 [1] Manufacturer's Product Number: 585 Our SKU: 585 Page ID: rut-585...
Our Answer: The NZ-62 is installed beneath the firebox of the NZ-26 or NZ-26WI and is used to direct the heat of the fireplace into the room in which it is located. The NZ62CH is a central heating system that allows the distribution of heated air int...
Our Answer: No, this kit will not work with your unit. Unfortunately, we are not a Heatilator dealer, so we are unable to provide the replacement panels you need. We recommend contacting a local Heatilator dealer or the manufacturer directly. Their w...
Our Answer: This hood will fit, as it is adjustable from 28" to 48". The hood is telescopic in the way it expands and contracts, so cutting the hood is not necessary, nor is it recommended. From Page: FSD-EUCH4L [1] Manufacturer's Product Number...
Our Answer: Actually, yes. Kerosene is a preferred fuel choice for this stone lighter. From Page: CPF-61098 [1] Manufacturer's Product Number: 61098 Our SKU: 61098 Page ID: cpf-61098 Links: ------ [1] http://www.efireplacestore.com/cpf-61098...
Our Answer: It is not uncommon for walls to be renovated to accept new appliances. However, before beginning any reframing project, you'll want to be sure that you are not cutting out any load bearing supports or removing any components that are vita...
Our Answer: This item is not designed for use with Dura Vent's double wall stovepipe. However, our 69183 should be what you are looking for. Please follow the below link to view this product. Dura-Vent 6 Inch Diameter to 8 Inch Diameter Increaser [1]...
Our Answer: Per your application, i would recommend one of our direct vent fireplaces. Vent-Free appliances are not to be installed in bedrooms - no matter their size. However, our direct vent appliances are very efficient and have no such limitation...
Our Answer: It is very possible that the damper plate may have become brittle and cracked. I cannot say that I have seen a plate that has any sort of cutout made into it, as this would allow air to leak into the fireplace. To be certain, please submi...
Our Answer: Yes, this fireplace may be installed into a wall. Please see the owner's manual for more information (you can download it on this product page). On page 11 of that manual, you will see the framing dimensions for this unit for installing i...
Our Answer: We do indeed have a few vent free inserts that would work for you. Please follow the below link to view these products. Please keep in mind that these items will require a surround kit to finish installation. These surround kits can be fo...
Our Answer: The easiest and best option would be to simply replace that control. Even if you were able to get the collar back onto the worm gear, it will likely pop back off, especially if the unit is bent. A set screw holds the shaft assembly to the...
Our Answer: The process for converting a fireplace from natural gas to LP will depend mostly on the brand, model, and type of fireplace. We will be happy to check into the availability of a conversion kit. Please provide the brand and model of the un...
Our Answer: An air mixer is indeed required, however Peterson does not offer a specific model for this item. It will be necessary to procure the air mixer from a plumbing supply store. From Page: PTS-LC-1 [1] Manufacturer's Product Number: LC-1 ...
Our Answer: Depending on application and ambient conditions, this RTV could take up to 7 days to fully cure. Once cured, it will accept high temp paint. From Page: FSD-71 [1] Manufacturer's Product Number: AWP-71 Our SKU: AWP-71 Page ID: fsd...
Our Answer: I think you're exactly correct. The heat of the stove is likely causing your elbow to rust out. We have the CPF-73835 elbows available as we do lengths of pipe. This Snap-Lock pipe is available in 12 and 24 inch lengths. You may view our ...
Our Answer: The outside dimensions of each leg measure 6" and the overall maximum width is 53.5". This can be adjusted to a narrower width, as each top piece can slide in and out to adjust. I cannot guarantee that the surround will work with any unit...
Our Answer: Our electric fireplaces simply plug into an electrical outlet for operation. There is no use of gas, only electricity. From Page: FSD-18DM1141EPOA-SO [1] Manufacturer's Product Number: 18DM1141EPOA/SO Our SKU: 18DM1141EPOA/SO Pag...
Our Answer: I highly recommend using a hood to deflect the heat from the fireplace around the t.v. An item such as this model would be ideal: Elite Adjustable 6 Inch Fireplace Hood with Surface Mount [1] This hood can be mounted directly to the face ...
Our Answer: As it turns out, yes. Per your stove's installation manual, this Majestic fan will indeed work with your Vermont Castings stove. From Page: MAJ-FK26 [1] Manufacturer's Product Number: FK26 Our SKU: FK26 Page ID: maj-fk26 Links: -...
Our Answer: Unfortunately, we do not offer the components necessary to accomplish a retrofit of this nature. In fact, many manufacturers recommend against such a renovation. From Page: CUI-VFD26FP30L10N [1] Manufacturer's Product Number: VFD-26-...
Our Answer: Upon checking further with the manufacturer, your fireplace does indeed have an integral receiver that is part of the unit's gas valve. This was a proprietary system that was developed by Vermont Castings and used by Majestic as well. Thi...
Our Answer: Unfortunately, we do not have any screens large enough for your opening. In Response to Question: We have an arched fireplace large enough to burn a forest in. It currently has a mesh 2 piece screen mounted internally that we are thi...
Our Answer: This door is designed to be used specifically with FMI's Mission fireplaces. It is strongly recommend that doors not be installed on fireplaces with ventless gas logs. A universal fit door would probably be the best option for you if you ...
Our Answer: The Colonial unit is simply a firebox and has no gas preference. It can be installed for use with natural gas or propane. The log set that you've installed in the Colonial will be the unit that you will need to address. Each manufacturer ...
Our Answer: Most commonly, a misadjusted thermopile is what causes the pilot to extinguish. As you mention, the voltage reading are within specification, so this would not be the issue. Improper venting can cause this issue, but it is usually not a r...
Our Answer: Napoleon's EFC32 surround features a painted black finish. From Page: NPL-EFC32 [1] Manufacturer's Product Number: EFC32H Our SKU: EFC32H Page ID: npl-efc32 Links: ------ [1] http://www.efireplacestore.com/npl-efc32.html
Our Answer: The manual for this unit does indeed seem to show wooden framing members, but this insert is only intended for use in a masonry fireplace. Some manufacturers use a universal diagram to display framing dimensions, only changing the numbers...
Our Answer: Unfortunately, we only offer two varieties of screen rod and as you found, they only adjust down to 32". We apologize for the inconvenience. From Page: FSD-RMP2426 [1] Manufacturer's Product Number: RMP2426 Our SKU: RMP2426 Page ...
Our Answer: After confirming with the manufacturer, your chimney height would allow the use of either 3" or 4" diameter venting, but 4" would yield better performance given your elevation. In Response to Question: I am planning to place an order ...
Our Answer: This insert uses a millivolt pilot system that does not require electricity for operation. However, the blower does require an outlet for its cord to be plugged in to work. You can add an optional remote control for this insert, but it is...
Our Answer: This unit is very straight forward to install and only requires that you locate a pair of wall studs to secure the supplied wall mounting bracket in position. You would then attach the bracket, using the supplied hardware, then hang the u...
Our Answer: Unfortunately, we do not offer a stainless steel door for this unit. Moreover, this unit is not truly designed to be installed outdoors - even halfway. The steel body of the fireplace is simply not made to withstand the corrosive nature o...
Our Answer: Indeed, gasket tape does require gasket cement. We have multiple sizes of cartridges available. Please view one of our options below. Rutland 10.3 oz. Cartridge of Black Stove Gasket Cement [1] From Page: FSD-120 [2] Manufacturer's Pr...
Our Answer: Please follow this link [1] to this model's installation guide. In Response to Question: Hello! I am unfamiliar with the Empire Tahoe brand of fireplace. Do you have any information on their products beyond the description on the web...
Our Answer: This unit is indeed a three-sided unit. Venting straight up is actually a requirement for these B-Vent appliances. Your application would pose no issues. Please follow the below link to view some of our venting components. B-Vent Chimney ...
Our Answer: Each brick on these panels measures 2" h x 6" w. It is strongly recommended to NOT use any sealant with these panels, as the heat will cause them to expand, and the use of any sealant is going to cause them to crack. There are no dedicate...
Our Answer: Unfortunately, you are not going to be able to put any different burner or logs in your fireplace. That is a direct vent fireplace, and it was engineered to work only with the burner and logs you received with it. The vented gas log sets ...
Our Answer: Per the manufacturer, the distance from the front of the pedestal to the center of the flue collar is 17" on both the 2000 and 2500 stoves. From Page: USS-2500 [1] Manufacturer's Product Number: 2500 Our SKU: 2500 Page ID: uss-250...
Our Answer: I am unfamiliar with Peterson's SV-12. From my research, it appears that it is simply an On/Off valve with no pilot assembly. The SPK-26 is more of a safety control valve that closes gas flow to the burner automatically if the pilot flame...
Our Answer: The item you have inquired about is a vented coal basket. Please see this vent-free coal basket for something you may like: Victorian Hearth Vent-Free Natural Gas Burner with Realistic Coals - 16.5 Inch [1] Please note that this basket is...
Our Answer: As you may have seen, the majority of our fireplaces require a 8" flue. However, our Monaco by Flame only requires a 6" chimney system. Please follow the below link to view this appliance. Flame Monaco XTD EPA Zero Clearance Fireplace [1]...
Our Answer: In order to make sure this adaptor would work for you, it will be necessary to measure the long and short sides of the oval. The long side needs to be 7" across and the short side 6" across for this adaptor to fit. On many older stoves, t...
Our Answer: This unit would be ideal for your application. It does not come with any brushes nor does it readily accept square brushes. However, there is an adaptor available that allows this unit to be compatible with them. We could special order it...
Our Answer: In order to repair the crack in your stove, I would recommend the following item: Rutland Pre-Mixed Black Furnace Cement - 10.3 Ounce Cartridge [1] This type of furnace cement is specifically made to bridge the size of gap you have and st...
Our Answer: All of our inserts include burners and log sets. We do not currently offer any that would allow the usage of your current set. Our VI33PBR, being a complete insert and burner assembly, would indeed be an efficient option. You would simply...
Our Answer: Yes, check the data plate on your heater and you should be able to identify a model number. With this information (and the manufacturer), we may be able to assist you in finding a blower for your heater. From Page: CUI-SC/CK18T [1] M...
Our Answer: This pipe will not work for you. Each brand of chimney pipe features brand specific locking tabs at their connection points. As such, if you have Security pipe, you must stick with it. Unfortunately, we do not currently carry 7" chimney p...
Our Answer: This door only requires a masonry opening of 4 5/8" x 8 5/8" - just a tad larger than a standard brick. Once installed, the outer trim will cover 5 1/2" x 9 1/2". In Response to Question: Hello, Was wondering if a door of some kind i...
Our Answer: Per the manufacturer, the approximate overall height of this unit is 14" at the center of the back arch. This unit can be used in any wood burning fireplace that has been approved for decorative gas hearth appliances. From Page: FSD-OBC...
Our Answer: This shelf uses a wall cleat for installation. The cleat will need to be anchored to the masonry or drywall above the fireplace opening and leveled. The shelf will then be pushed down on to the cleat until it snaps into position. The manu...
Our Answer: In a word, yes. This 61066 is indeed the clean-out door that goes into the floor of your fireplace for quick clean up. From Page: CPF-61066 [1] Manufacturer's Product Number: 61066 Our SKU: 61066 Page ID: cpf-61066 Links: ------...
Our Answer: Based on the detailed information that you have provided, this type of grate would be a good choice for your needs. Depth and width of the grate would make this a good match and the height of the grate falls within the recommended specifi...
Our Answer: Being submerged in water causes singular damage to gas appliances. Manufacturers, Napoleon included, recommend against ever using an appliance that has been under water. In Response to Question: I purchased the star fire fireplace 2 ...
Our Answer: You would be able to slightly recess the bend of the elbow into the fire stop, but only by a couple of inches. Any further and the elbow is likely to not have sufficient clearance from the top of the joist. If additional piping is needed,...
Our Answer: When installing a pellet insert into an existing masonry fireplace, it is necessary to line the chimney with a stainless steel liner. This insert can be utilized with a 3" flexible or rigid liner, although flexible is usually the better c...
Our Answer: Panels, such as the ones this question was placed under, are the only models that we have to fit a discontinued fireplace such as yours. These universal Hargrove panels can be cut to fit and serve as good replacements for most models of f...
Our Answer: Wind should not be an issue for this cap, and, if twist-locked correctly onto DuraTech 8" pipe, it should not come apart as you described. As a result, there is no additional item to help with this. I have found your order using your emai...
Our Answer: Unfortunately, there is no real way to convert a gas fireplace to a wood burning appliance. You would need to completely replace your existing unit with a wood burner. You would then need to build a chimney system for it. If you'd like to...
Our Answer: Technically, yes. You could use a log lighter for this conversion. However, one of our round firepit burner assemblies would be more ideal for such a renovation. Please follow the below link to view these products. Fire Pit Accessories [1...
Our Answer: The battery backup for the signature command system is actually designed to be mounted in the bottom of the unit, near the control board. It is wired to the gas valve to supply power for operation in the event of a power outage. The unit ...
Our Answer: If you are looking for a primary heat source for your cabin, it is better to go with direct vent over B-vent for efficiency. Some of our stoves can be B-vent or direct vent, but for performance we recommend going with the direct vent set-...
Our Answer: This unit is capable of heating up to 1600 square feet. You may be interested in any of Timberwolf stoves by Napoleon. Either the 2100, 2200, or 2300 by Napoleon feature an efficiency rating higher than 80%. Unfortunately, they are not qu...
Our Answer: As long as the inside diameter of your existing pipe is indeed 8", you should be able to drop your new direct vent pipe down through it. As such, your 8" pipe would simply be working as a chase for your direct vent pipe. In Response to...
Our Answer: Your CDV 36 would not accept this front. The VD32AFB would be correct, though. You may find this item by following the below link. Majestic VD32AFB Black Designer Arched Front with Lower Control Door [1] To complete this look, you would a...
Our Answer: Typically, the brackets are able to be seen and sit on the front side of the panels, retaining them again the fireplace on the upper side of the unit. There are usually no brackets on the bottom, as the panels sit into a groove on the bot...
Our Answer: Per our representative at FireSense, please give them a call directly at 800-766-9633 Ext. 230 to discuss the issue. We can usually send a remote out via your address information, but I was not able to find you in our system. The represen...
Our Answer: This item is the piece labeled "B" in the picture. Item #CPF-21375 is item "A" in the picture. The only other difference is that item #CPF-21375 ("A") has a slight offset, whereas this item ("B") is straight. From Page: CPF-21376 [1] ...
Our Answer: This termination should work for your application, based on the dimensions of your flue. The mounting collar is collapsible, down to 7 inches in diameter. It comes as a standard size of 11 inches and uses sizing rings to achieve fitment f...
Our Answer: Actually, no. You would want either the BLOTMC or the FK-180. Please follow the below links to view these products. BLOTMC [1] FK-180 [2] From Page: CUI-BK3 [3] Manufacturer's Product Number: BK3 Our SKU: BK3 Page ID: cui-bk3 Lin...
Our Answer: This mantel will work just fine for your application. However, it may be necessary to shim beneath the mantel in the areas that are not attached to the tile. This will prevent the appearance of any gaps behind the mantel. From Page: CU...
Our Answer: I was not successful with the manufacturer, however our distributor was kind enough to pull a liner from stock and measure the panels. Measurements are as follows: Rear panel - 26 inches tall by 28 5/16 inches wide Side panels - 26 1/2 in...
Our Answer: While your width measurement is adequate for either the 24" or the 18' version of this log set, your depth measurement is too narrow. Unfortunately, we do not currently offer a see-thru ventless log set that that matches your dimensions. ...
Our Answer: It seems that you need a natural gas starter pipe to install in your woodburning fireplace. Please see our options below: Copperfield T-Style Gas Starter Pipe with Mixing Chamber for Natural Gas [1] (This is item "A" in the picture.) Copp...
Our Answer: The fireplace does not include a surround, but one is not required. The fireplace can indeed be installed as received, and the surround options are not necessary, but only for aesthetic enhancement. Please see the optional surrounds for t...
Our Answer: Unfortunately, this item is not listed to Phase 11 requirements and does not carry a UL or Omni listing. This surround is manufactured by Victorian Hearth in England, and then imported. As a result, it does not come with listings that are...
Our Answer: Correct. The fan needs to be located in the back of the fireplace, in order for it to effectively circulate air up and out of the top louvers. Depending on how the fan was installed, you may need to remove the brick liner on the floor to ...
Our Answer: This Echelon is indeed among our largest see-thru units. However, our 48 Inch Marquis by Majestic is a bit larger. Please follow the below link to check it out. Majestic 48 Inch Marquis Clean Face See-Thru Direct Vent Gas Fireplace with S...
Our Answer: Yes, this liner can be used to vent select Napoleon direct vent gas fireplaces without the need to enclose it in a noncombustible chimney. From Page: NPL-GD430 [1] Manufacturer's Product Number: GD430 Our SKU: GD430 Page ID: npl-...
Our Answer: This item uses a receiver that must mount within the unit. As a result, you may use the switch or a remote, but not both devices. The switch is designed for appliances with millivolt or electronic valves, but cannot be utilized in a solen...
Our Answer: Our Glowing Embers and Rock Wool are similar products. Both are designed to replenish ember beds of vented gas appliances. The Glowing Embers are simply manufactured by R. H. Peterson for their line of product. In Response to Question:...
Our Answer: Yes, this thermostat will include both a receiver and the wall-mount control unit. The receiver can indeed be hidden behind the stove. In Response to Question: I have an Empire Mantis Stove. Due to wiring difficulties I need a remote...
Our Answer: Generally, it is best to use a fireplace hood to deflect the heat from the mantel and/or T.V. You may view an example here: Elite Adjustable 6 Inch Fireplace Hood with Surface Mount [1] This model is designed to mount to the facing, just ...
Our Answer: These remote controls are only available as complete kits with both the hand-held transmitter and the receiver. From Page: CUI-1001BE [1] Manufacturer's Product Number: SKY-1001BE Our SKU: SKY-1001BE Page ID: cui-1001be Links: --...
Our Answer: Indeed, it is. That installation would work well for Napoleon's GVF. Because this unit is ventless, the accessories you mentioned are really all that are needed. In Response to Question: I would like to frame in and use artificial st...
Our Answer: Safety pilot valves will stop the gas flow to the fire glass set, in the event that the flame should extinguish for any reason. Safety pilot valves also have an oxygen depletion sensor built into them, which will shut the unit down comple...
Our Answer: Unfortunately, we no longer offer the actual bio fuel for these units. Due to shipping restrictions imposed by the company, only authorized local dealers carry the fuel. It can often be purchased at hearth and home improvement stores and ...
Our Answer: A single 12 ounce can will cover approximately 4 to 10 square feet. However, this will depend on the color being painted over and the condition of the metal. Individual painting technique also plays a factor. From Page: FSD-92AW [1] M...
Our Answer: This unit is simply a firebox not a fireplace. So, technically it has no BTU rating. However, due to its size, it can accommodate either a 24" or 27" multi-sided vent free log set. These log sets are capable of up to 39,000 BTU. Please fo...
Our Answer: The Classic Flame insert model is the 28II200GRA. From Page: FSD-28WM1127ERCR-SO [1] Manufacturer's Product Number: 28WM1127ERCR/SO Our SKU: 28WM1127ERCR/SO Page ID: fsd-28wm1127ercr-so Links: ------ [1] http://www.efireplacesto...
Our Answer: Our platinum bright embers weigh 5 grams: Platinum Bright Embers [1] Please let us know if you have any additional questions. From Page: ACS-PBE [2] Manufacturer's Product Number: PBE Our SKU: PBE Page ID: acs-pbe Links: ------ [...
Our Answer: Unfortunately, no. The fireplace does not come with the mantel; rather, that is a custom mantel used for the stock photo. From Page: MAJ-MLDV500PSC [1] Manufacturer's Product Number: MLDV500PSC Our SKU: MLDV500PSC Page ID: maj-ml...
Our Answer: To start your venting run, you would need an appliance adapter. This will be the connecting device between the pipe and your flue outlet. Stovepipe Stove Adaptor [1] Double wall pipe would work just fine with your wood stove. Also, our Se...
Our Answer: Unfortunately, I am not certain if this gasket will be the proper size for your pellet insert. Because we are not a dealer of Quadra-Fire products, I do not have archived information for their products. My recommendation would be to consu...
Our Answer: Please find the specifications for this item below: LCUF Universal Low Rider Vent-Free Firebox with Firebrick Installed [1] Style: Single face fireplace Fuel Type: Natural Gas Width: 41" Height: 37.375" Depth: 20.5" Viewing Area: 33.875" ...
Our Answer: This item is a firebox only and does not include a log set, burner assembly, or blower. You may find a suitable log set for this box by checking out our See Through Vent Free log sets. Simply follow the below link. Vent Free Gas Logs [1] ...
Our Answer: Unfortunately, we do not currently have a picture of this particular mantel with a white finish. Please see this Empire corner mantel in white for the closest thing we have to what you need: Empire EMBC11S Corner Wooden Mantel Cabinet wit...
Our Answer: Unfortunately, no. This key fits only 1/4" and 5/16" gas valve stems. From Page: DNT-NKY-18-BR-B [1] Manufacturer's Product Number: NKY.18.BR.B Our SKU: NKY.18.BR.B Page ID: dnt-nky-18-br-b Links: ------ [1] http://www.efireplace...
Our Answer: Yes, this unit comes with the Napoleon Phazer glowing log set and charcoal embers. From Page: NPL-BGD42N-D [1] Manufacturer's Product Number: BGD42N-D Our SKU: BGD42N-D Page ID: npl-bgd42n-d Links: ------ [1] http://www.efirepla...
Our Answer: These trivets are only meant for use with Napoleon's GDS50, 1400, and 1900 stoves. We do offer this trivet: Copperfield Black Enamel Trivet [1] Unfortunately, this trivet is only recommended for use up to 300 degrees, not the 600 you need...
Our Answer: Unfortunately, this will not fit your stove. This door frame is only for use with Empire's 42" Breckenridge Deluxe fireboxes. We recommend that you contact the manufacturer to check availability of the screen for your unit. From Page: ...
Our Answer: This gasket does require the addition of adhesive. Please follow the below link to view one of our cement options. AW Perkins Black Stove and Gasket Cement [1] From Page: CPF-81275 [2] Manufacturer's Product Number: 1095 Our SKU: 10...
Our Answer: No, it will not work in a power outage as it requires a 110 volt plug-in (standard outlet) to operate. Please see this alternative, if you need a unit with a standing pilot: Empire DV55SPP Direct Vent Counterflow Wall Furnace with Standin...
Our Answer: If your receiver is failing to respond to your transmitter after new batteries have been installed in both, it is likely that one of those two components is indeed defective. It is recommended to replace them as a set. In fact, we do not ...
Our Answer: Unfortunately, I don't know of any local dealers of Victorian Hearth products, but below is a link to a dealer locater for Fireside Distributors: Fireside America Dealers [1] Fireside Distributors is the primary distributor for Victorian ...
Our Answer: The G46 is indeed a great burner assembly. It comes with the control valve of your choice pre-assembled to the burner pan. It also carries CSA/ANSI certification. Please follow the below link to view this log set with a G46 assembly. Real...
Our Answer: These units do not need to be recessed into a wall. The unit is only 14" deep but they can stand as proud of the wall as you'd prefer. You can custom build any mantel or surround around this unit per your application's criteria. We curren...
Our Answer: Yes, this unit telescopes from the fully extended height of 93" down to 73 1/4" for storage purposes. The manufacturer encourages consumers to operate it at the fully extended height, however, due to possibly of injury from contact with t...
Our Answer: This item carries a limited lifetime warranty. We'll be happy to resolve any issue that arises due to a manufacturing defect. From Page: FSD-18601 [1] Manufacturer's Product Number: 18601 Our SKU: 18601 Page ID: fsd-18601 Links:...
Our Answer: Unfortunately, the Chesapeake model is not available with electronic ignition at this time. From Page: MAJ-CFX24PVDW [1] Manufacturer's Product Number: CFX24PVDW Our SKU: CFX24PVDW Page ID: maj-cfx24pvdw Links: ------ [1] http:/...
Our Answer: The frame of the screen is constructed of mild steel. From Page: NPL-SC3 [1] Manufacturer's Product Number: SC3 Our SKU: SC3 Page ID: npl-sc3 Links: ------ [1] http://www.efireplacestore.com/npl-sc3.html
Our Answer: The outside diameter of this trim collar is 9.75". From Page: CPF-73665 [1] Manufacturer's Product Number: BM0094 Our SKU: BM0094 Page ID: cpf-73665 Links: ------ [1] http://www.efireplacestore.com/cpf-73665.html
Our Answer: I will most certainly be able to get a quote together for you. Vermont Castings products are able to utilize both Simpson Duravent and Monessen products, which we carry both of. What is the material on the outside wall this piping will be...
Our Answer: This is certainly a viable option, as long as proper clearance to the ceiling is maintained. The unit requires a minimum of 2 feet from the top of the standoffs to bottom of a combustible ceiling. Being that the unit has a height of 4 fee...
Our Answer: This item is a panel finishing kit for the old Hearth Sense RD-S wall mount fireplace, which was discontinued in 2010. From Page: FSD-R-SP-1 [1] Manufacturer's Product Number: R-SP-1 Our SKU: R-SP-1 Page ID: fsd-r-sp-1 Links: --...
Our Answer: It is never recommended to use a fireback with ventless gas logs, as the heat radiated back onto the pilot assembly will be too intense. From Page: CPF-70060 [1] Manufacturer's Product Number: 70060 Our SKU: 70060 Page ID: cpf-70...
Our Answer: The product is a low density variety of rope gasket. While we do have some gasket material that is slightly denser than this product, we currently only carry low density varieties. We are working with the manufacturer to pick up a high de...
Our Answer: While the unit does not come from the factory with a thermostat, you can certainly equip the fireplace with a remote or wall mounted thermostatic control. Both of these items can be seen at the links below. Please keep in mind that you ma...
Our Answer: For minimum mantel clearances, please refer to page 11 of the owner's manual (can be downloaded on this item page). Per this diagram, you will need about 20" from the top of your opening to the mantel. From Page: CUI-VFB42C1 [1] Manu...
Our Answer: Per the manufacturer, there is no difference between the two models. This manufacturer functions a lot like Monessen and Majestic. Both companies are manufactured in the same facility and are absolutely identical, but are sold under two b...
Our Answer: Assuming your Majestic unit is equipped with the Signature Command system, and you have the SCSACM module, then yes, this accent light kit will plug in to that module, which is the same for the blower. In Response to Question: I have...
Our Answer: This particular unit has an overall efficiency rating of 75.4%, per Napoleon. This is one of three pellet models that we currently carry and has the lowest overall efficiency rating of them. The following model is currently the most effic...
Our Answer: These gas logs are for use only in masonry fireplaces or manufactured woodburning fireplaces that are "gas log ready." Your gas unit, whether it is B-vent or direct vent, is only intended to use the logs that came with it. From Page: P...
Our Answer: It is recommended that any wood stove be placed on a non-combustible surface. Most of our appliances require that they be placed on a hearth pad that extends at least 18" in front of the stove and 8" from the other three sides. That being...
Our Answer: For your pizza oven, we recommend the Rutland Stovo Fireplace, Stove, and Furnace Mortar - 1 Quart Tub [1]. From Page: RUT-63 [2] Manufacturer's Product Number: 63 Our SKU: 63 Page ID: rut-63 Links: ------ [1] http://www.efirepl...
Our Answer: You would not. These remotes are based on the exact same platform and the Signature Command system can be utilized with either remote. From Page: CUI-TSTSC [1] Manufacturer's Product Number: TSTSC Our SKU: TSTSC Page ID: cui-tstsc...
Our Answer: Unfortunately, we do not carry any other wall mounted, vent free units at this time that are gas fueled. All other models require the use of gel fuel or electricity for operation. We do have another variant that can be mounted on a wall, ...
Our Answer: This kit includes 10 lbs of bronze glass. From Page: PTS-G45-GL18Z-APK-17N [1] Manufacturer's Product Number: G45-GL18Z-APK-17N Our SKU: G45-GL18Z-APK-17N Page ID: pts-g45-gl18z-apk-17n Links: ------ [1] http://www.efireplacesto...
Our Answer: Unfortunately, the manufacturer does not currently offer a kit that has all black components. The appliance adapter and intake air components must be painted, if desired. The part number for the other components are as follows: Selkirk Di...
Our Answer: Napoleon's gas fireplaces and venting products, such as this item, are independently tested by Intertek. This testing agency is an equivalent of UL and is more common in Canada. Additional criteria that is met is the ISO 9001-2008 quality...
Our Answer: These spacers should work just fine for that application. Each of these 30 screws are 2 1/2" long. The spacers included are 1" long. That leaves plenty of screw left over to pass through your cement board and sink positively into the wall...
Our Answer: According to the manufacturer, the current system can be replaced with either the RCK-I or RCK-B Acumen remote controls. The FDC-501 came in both AC and DC versions. If you have the DC version (operated by battery pack) the RCK-I is the r...
Our Answer: While this unit does indeed use an air cooled chimney, the air in the outer sleeve does not interact with the interior of the unit. The outer sleeve remains open and uses air inside the chase to cool the unit. More likely, the cold air yo...
Our Answer: Indeed, since this is a direct vent unit, you can surely use this in a bedroom. From Page: CUI-VCD36RP [1] Manufacturer's Product Number: VCD36RP Our SKU: VCD36RP Page ID: cui-vcd36rp Links: ------ [1] http://www.efireplacestore....
Our Answer: Indeed it is. According to the manufacturer, this is made of hand-forged wrought iron. From Page: ADC-304100 [1] Manufacturer's Product Number: X304100 Our SKU: X304100 Page ID: adc-304100 Links: ------ [1] http://www.efireplace...
Our Answer: This unit can indeed be installed into a corner. Due to its size, it would require walls that are at least 57 7/8" long. This would place the glass of the fireplace 41" directly in front of the corner in which it is located. Please view p...
Our Answer: In searching through our available stove options, I was only able to find two that had efficiency rating higher than 80%. Each of these can accept logs larger than 18" The first is this Timberwolf 2300 by Napoleon and the other is the 150...
Our Answer: Napoleon does not provide an efficiency rating for this appliance. However, EPA testing shows that it is capable of 11.800 to 34,000 BTU. This capability translates to a heated area of approximately 1,000 to 3,500 square feet. From Pag...
Our Answer: These panels are designed for use inside a manufactured fireplace, rather than a true masonry setup. It would be necessary to reline the existing box with a product such as this: AW Perkins Castable Refractory Cement - 50 lb. Tub [1] This...
Our Answer: This particular stove uses a blower access panel on the back of the stove, near the top of the unit. The panel must be removed and the blower can be installed in place of the panel. Attachment hardware is provided to secure the blower in ...
Our Answer: These doors are made specifically for a collection of fireplaces by vantage Hearth. They measure approximately 21" tall. In Response to Question: I was wondering if you could tell me the total frame height on these doors. I have a un...
Our Answer: This remote does not allow for thermostatic control. It simply provides a display of the room temperature. However, the RCK-K, which can be found by following the below link, does indeed offer thermostatic control. RCK-K 5-Button Programm...
Our Answer: Unfortunately, not. This front is designed to be used specifically with Napoleon's GI3600. It will not work for your Osburn Bay Vista. In Response to Question: I am looking at your Napoleon GI3600 Gas Fireplace Bay Window Door Assemb...
Our Answer: This cap can accommodate flue openings as wide as 16 1/2" by 17". Its set screws should grip block just fine. From Page: CPF-13112 [1] Manufacturer's Product Number: 13112 Our SKU: 13112 Page ID: cpf-13112 Links: ------ [1] http...
Our Answer: This item is made in China. From Page: UF-C-1242 [1] Manufacturer's Product Number: C-1242 Our SKU: C-1242 Page ID: uf-c-1242 Links: ------ [1] http://www.efireplacestore.com/uf-c-1242.html
Our Answer: Aside from the tacks and nozzle, this bellows is indeed pine and leather. From Page: CPF-68050 [1] Manufacturer's Product Number: 1040 Our SKU: 1040 Page ID: cpf-68050 Links: ------ [1] http://www.efireplacestore.com/cpf-68050.h...
Our Answer: This stove is capable of 4600 BTU. That equates to an approximate heated area of 130 square feet. From Page: FRS-60353 [1] Manufacturer's Product Number: 60353 Our SKU: 60353 Page ID: frs-60353 Links: ------ [1] http://www.efire...
Our Answer: We have products by Pilgrim that are made in both the US and abroad. Please allow me to contact our manufacturer for exact information on this particular product. From Page: FSD-18519 [1] Manufacturer's Product Number: 18519 Our SK...
Our Answer: Per Napoleon, the EP65 is the blower kit by itself. The EP63 is the blower kit and the rear heat shield that is needed to install the blower. If you already have the heat shield installed, you will only need the EP65 blower. If there is n...
Our Answer: It s not recommended to stack refractory panels. Per your application, the proper repair would be replacing the panel with a common sized unit. Our Hargrove panels could be used as your bottom panel, if they are the same as your original....